charging LAND ROVER FREELANDER 2001 Owner's Manual

AUTOMATIC GEARBOX - JATCO
REPAIRS 44-23
23.Fit CKP sensor, fit bolt and tighten to 9 Nm (7
lbf.ft).
24.Position fluid cooler, tighten M12 bolts to 85 Nm
(63 lbf.ft) and M8 bolt to 25 Nm (18 lbf.ft).
25.Clean fluid cooler unions.
26.Lubricate new 'O' rings with clean transmission
fluid and fit 'O' rings to fluid cooler hoses.

+ CAPACITIES, FLUIDS,
LUBRICANTS AND SEALANTS,
Lubrication.
27.Connect fluid cooler hoses to gearbox and
tighten unions to 18 Nm (13 lbf.ft).
28.Clean exhaust manifold and mating face on
cylinder head.
29.Fit exhaust manifold gasket.
30.Position exhaust manifold, fit nuts and
progressively tighten, from centre outwards to
45 Nm (33 lbf.ft).
31.Connect HO2S multiplug and secure to support
bracket.
32.Position IRD cooling hose retainer, fit bolt and
tighten to 25 Nm (18 lbf.ft).
33.Align marks on drive plate to torque converter.
34.Fit bolts securing drive plate to torque converter
and tighten bolts to 45 Nm (33 lbf.ft).
35.Clean torque converter access plate.
36.Position access plate, fit bolts and tighten to 9
Nm (7 lbf.ft).
37.Clean end of drive shaft and mating splines in
gearbox.
38.Fit new circlip to LH drive shaft.
39.With assistance pull hub outwards, align drive
shaft and fit to gearbox, taking care not to
damage drive shaft oil seal.
CAUTION: Pull the drive shaft to ensure the
circlip is fully engaged and retains the shaft.
40.Fit splash shield and secure with bolts.
41.Position trunnion to selector lever, locate inner
cable through trunnion, do not tighten nut at this
stage.
42.Position selector cable to gearbox bracket and
secure with clip.
43.Adjust selector cable.

+ AUTOMATIC GEARBOX - JATCO,
ADJUSTMENTS, Selector cable - adjust.
44.Fit IRD.

+ INTERMEDIATE REDUCTION
DRIVE, REPAIRS, Intermediate reduction
drive (IRD) unit - KV6.
45.Connect battery earth lead.
46.Fit engine acoustic cover.

+ ENGINE - K SERIES KV6, REPAIRS,
Cover - engine acoustic.
47.Untie and close bonnet.
Gearbox - Td4
$% 44.20.02.99
Remove
1.Disconnect battery earth lead.
2.Tie bonnet back in upright position.
3.Remove intake ducting assembly.

+ FUEL DELIVERY SYSTEM - DIESEL,
REPAIRS, Ducting - intake assembly.
4.Remove fluid cooler.

+ AUTOMATIC GEARBOX - JATCO,
REPAIRS, Fluid cooler - Td4.
5.Remove starter motor.

+ CHARGING AND STARTING,
REPAIRS, Starter motor - Td4.
6.Remove IRD.

+ INTERMEDIATE REDUCTION
DRIVE, REPAIRS, Intermediate reduction
drive (IRD) unit - Td4.
7.Secure LRT-54-026 to drive shaft inboard joint.
Using a suitable lever, release inboard joint
from gearbox.
8.With assistance, pull hub outwards and remove
LH drive shaft from gearbox.
CAUTION: Pull the drive shaft horizontally
to avoid damaging the differential oil seal.

AUTOMATIC GEARBOX - JATCO
REPAIRS 44-27
21.Fit new circlip to LH drive shaft.
22.With assistance, fit LH drive shaft to gearbox,
keep shaft square to prevent damage to oil seal
in gearbox.
23.Fit IRD.

+ INTERMEDIATE REDUCTION
DRIVE, REPAIRS, Intermediate reduction
drive (IRD) unit - Td4.
24.Fit starter motor.

+ CHARGING AND STARTING,
REPAIRS, Starter motor - Td4.
25.Fit fluid cooler.

+ AUTOMATIC GEARBOX - JATCO,
REPAIRS, Fluid cooler - Td4.
26.Fit intake ducting assembly.

+ FUEL DELIVERY SYSTEM - DIESEL,
REPAIRS, Ducting - intake assembly.
27.Connect battery earth lead.
28.Untie and close bonnet.
Fluid pan - reseal
$% 44.24.05
Remove
1.Drain gearbox fluid.

+ AUTOMATIC GEARBOX - JATCO,
ADJUSTMENTS, Gearbox fluid - drain &
refill.
2.Remove fluid cooler.

+ AUTOMATIC GEARBOX - JATCO,
REPAIRS, Fluid cooler - KV6.
3.Release multiplugs from clips attached to fluid
pan.
4.Remove 21 bolts securing fluid pan to gearbox.
5.Remove fluid pan.
Refit
1.Clean fluid pan and mating face on gearbox.
2.Apply sealant, Part No. STC 4600to contact
faces of fluid pan and gearbox.
3.Position fluid pan, fit bolts and tighten
progressively to 7 Nm (5 lbf.ft).
4.Secure multiplugs to clips.
5.Fit fluid cooler.

+ AUTOMATIC GEARBOX - JATCO,
REPAIRS, Fluid cooler - KV6.
6.Fill gearbox with fluid.

+ AUTOMATIC GEARBOX - JATCO,
ADJUSTMENTS, Gearbox fluid - drain &
refill.

STEERING
REPAIRS 57-15
Pump - steering - Td4
$% 57.20.14
Remove
1.Disconnect battery earth lead.
2.Remove hydramount.

+ ENGINE - Td4, REPAIRS,
Hydramount - engine - RH.
3.Loosen 3 PAS pump pulley bolts.
4.Remove ancillary drive belt.

+ CHARGING AND STARTING,
REPAIRS, Ancillary drive belt - Td4.
5.Raise engine on hoist.
6.Remove bolts and remove PAS pump pulley.
7.Cover alternator to prevent PAS oil
contamination.
8.Place container beneath PAS pump, release
clip and remove feed hose to pump. Allow fluid
to drain.
CAUTION: Care must be taken to ensure
that oil or fluid does not enter or
contaminate the alternator.9.Remove banjo bolt securing fluid outlet hose to
PAS pump, release hose, remove and discard
sealing washers.
CAUTION: Before disconnecting or
removing components, ensure the
immediate area around joint faces and
connections are clean. Plug open
connections to prevent contamination.
10.Remove 4 bolts and remove PAS pump.
11.Remove 5 Torx bolts securing PAS pump to
mounting brackets. Collect mounting brackets.
Refit
1.Position PAS pump to mounting brackets, fit
and tighten Torx bolts to 25 Nm (18 lbf.ft).
2.Position pump to mounting, fit bolts and tighten
M8 bolts to 25 Nm (18 lbf.ft) and M6 bolts to 10
Nm (7.5 lbf.ft).
3.Using new sealing washers, fit PAS outlet hose
to pump and tighten banjo bolt to 25 Nm (18
lbf.ft).
4.Clean PAS pump and mating faces.
5.Fit inlet hose to PAS pump and secure with new
clip.
6.Fit PAS pump pulley to PAS pump and tighten
bolts to finger tight.
7.Fit ancillary drive belt.

+ CHARGING AND STARTING,
REPAIRS, Ancillary drive belt - Td4.
8.Tighten PAS pump pulley bolts to 10 Nm (7.5
lbf.ft).
9.Fit hydramount.

+ ENGINE - Td4, REPAIRS,
Hydramount - engine - RH.
10.Connect battery earth lead.

BRAKES
REPAIRS 70-27
Sensor & harness - front wheel - LH
$% 70.65.30
Remove
1.Remove battery carrier.

+ CHARGING AND STARTING,
REPAIRS, Carrier - battery.
2.Raise front of vehicle.
WARNING: Do not work on or under a
vehicle supported only by a jack. Always
support the vehicle on safety stands.
3.Remove road wheel.
4.Remove front wheel arch liner.

+ EXTERIOR FITTINGS, REPAIRS,
Liner - front wheel arch.
5.Locate ABS sensor harness on inner wing.
6.Release ABS sensor multiplug from body clip
and disconnect multiplug.
7.Release grommet from wing valance and pull
harness through.8.Release 2 grommets from wing valance and
damper brackets
9.Release harness from brake hose clips.
10.Remove bolt securing ABS sensor to hub, if
fitted.
11.Release ABS sensor from hub.
12.Remove ABS sensor and harness.
13.Remove bush from front hub.

BRAKES
70-28 REPAIRS
Refit
1.Clean ABS sensors and mating faces.
2.Fit new bush to front hub.
3.Apply anti-seize grease to sensor.
4.Fit sensor to hub, ensure sensor is fully seated
in hub.
CAUTION: Ensure ABS sensor is fully
located into hub, so that sensor touches
pole wheel teeth.
5.Fit bolt securing ABS sensor to hub, if fitted.
6.Secure harness grommets to brackets.
7.Pass sensor harness through wing valance and
secure grommet.
8.Ensure 'O' ring is in place and connect sensor
multiplug to body harness.
9.Secure multiplug in body clip.
10.Secure harness to brake hose clip.
11.Fit front wheel arch liner.

+ EXTERIOR FITTINGS, REPAIRS,
Liner - front wheel arch.
12.Fit battery carrier.

+ CHARGING AND STARTING,
REPAIRS, Carrier - battery.
13.Fit road wheel(s) and tighten nuts to 115 Nm
(85 lbf.ft).
14.Remove stand and lower vehicle.
15.To ensure correct operation, the ABS system
MUST be tested using TestBook/T4.

PANEL REPAIRS
REPAIRS 77-2-25
REPAIRS
Front bulkhead assembly
In this procedure, the crossmember gusset plates
are replaced in conjunction with the front bulkhead
assembly.
Remove
1.Disconnect battery earth lead.
2.Disconnect alternator.
3.Disconnect all ECUs.
4.Remove front bumper valance.

+ EXTERIOR FITTINGS, REPAIRS,
Bumper - assembly - front - up to 04MY.
5.Remove front bumper armature.
6.Remove radiator.

+ COOLING SYSTEM - K SERIES KV6,
REPAIRS, Radiator assembly.
7.Remove PAS fluid cooler.

+ STEERING, REPAIRS, Oil cooler -
Td4 & K1.8 models.
8.Remove LH and RH headlamps.

+ LIGHTING, REPAIRS, Headlamp
assembly - up to 04MY.
9.Release wiring to headlamps and position
aside.
10.Remove LH and RH engine bay shields.
11.Remove bumper valance LH and RH
attachment brackets.
12.Remove battery.

+ CHARGING AND STARTING,
REPAIRS, Battery.
13.Remove air intake hose.
14.Remove horn.

+ SECURITY, REPAIRS, Horn.
15.Remove windscreen washer reservoir.

+ WIPERS AND WASHERS, REPAIRS,
Reservoir - washer.
16.Remove bonnet lock.
17.Support bonnet in open position.
18.Remove bonnet stay. Repair
1.Remove existing panel(s), prepare panel joint
faces and install new panel(s) in accordance
with Panel Replacement Procedure. Punch or
drill holes in new panel for plug welding as
shown.

PANEL REPAIRS
77-2-26 REPAIRS
Refit
1.Fit bonnet stay.
2.Fit bonnet lock.
3.Fit windscreen washer reservoir.

+ WIPERS AND WASHERS, REPAIRS,
Reservoir - washer.
4.Fit horn.

+ SECURITY, REPAIRS, Horn.
5.Fit air intake hose.
6.Fit battery. Do not connect earth lead.

+ CHARGING AND STARTING,
REPAIRS, Battery.
7.Fit bumper valance LH and RH attachment
brackets.
8.Fit LH and RH engine bay shields.
9.Fit LH and RH headlamps.

+ LIGHTING, REPAIRS, Headlamp
assembly - up to 04MY. Secure headlamps
wiring.
10.Fit PAS fluid cooler.

+ STEERING, REPAIRS, Oil cooler -
Td4 & K1.8 models.
11.Fit radiator.

+ COOLING SYSTEM - K SERIES KV6,
REPAIRS, Radiator assembly.
12.Fit front bumper armature.
13.Fit front bumper valance.

+ EXTERIOR FITTINGS, REPAIRS,
Bumper - assembly - front - up to 04MY.
14.Connect all ECUs.
15.Connect alternator.
16.Connect battery earth lead.

PANEL REPAIRS
REPAIRS 77-2-27
Bonnet locking platform
In this procedure the bonnet locking platform
reinforcement is also replaced in conjunction with the
bonnet locking platform.
Remove
1.Disconnect battery earth lead.
2.Disconnect alternator.
3.Disconnect all ECUs.
4.Remove front bumper valance.

+ EXTERIOR FITTINGS, REPAIRS,
Bumper - assembly - front - up to 04MY.
5.Remove radiator.

+ COOLING SYSTEM - K SERIES KV6,
REPAIRS, Radiator assembly.
6.Remove both headlamp assemblies.

+ LIGHTING, REPAIRS, Headlamp
assembly - up to 04MY.
7.Remove horn.

+ SECURITY, REPAIRS, Horn.
8.Remove battery.

+ CHARGING AND STARTING,
REPAIRS, Battery.
9.Remove air intake hose.
10.Remove bonnet lock.
11.Support bonnet in open position.
12.Remove bonnet stay.
Repair
1.Remove existing panel(s), prepare panel joint
faces and install new panel(s) in accordance
with Panel Replacement Procedure. Refit
1.Fit bonnet stay.
2.Fit bonnet lock.
3.Fit air intake hose.
4.Fit battery. Do not connect earth lead.

+ CHARGING AND STARTING,
REPAIRS, Battery.
5.Fit horn.

+ SECURITY, REPAIRS, Horn.
6.Fit both headlamp assemblies.

+ LIGHTING, REPAIRS, Headlamp
assembly - up to 04MY.
7.Fit radiator.

+ COOLING SYSTEM - K SERIES KV6,
REPAIRS, Radiator assembly.
8.Fit front bumper valance.

+ EXTERIOR FITTINGS, REPAIRS,
Bumper - assembly - front - up to 04MY.
9.Connect all ECUs.
10.Connect alternator.
11.Connect battery earth lead.

PANEL REPAIRS
77-2-28 REPAIRS
Headlamp mounting panel
Remove
1.Disconnect battery earth lead.
2.Disconnect alternator.
3.Disconnect all ECUs.
4.Remove front bumper valance.

+ EXTERIOR FITTINGS, REPAIRS,
Bumper - assembly - front - up to 04MY.
5.Remove front bumper armature.
6.Remove radiator.

+ COOLING SYSTEM - K SERIES KV6,
REPAIRS, Radiator assembly.
7.Remove headlamp assembly.

+ LIGHTING, REPAIRS, Headlamp
assembly - up to 04MY.
8.Release wiring to headlamp and position aside.
9. LH side: Remove front bumper LH support
bracket.
10. LH side: Remove battery.

+ CHARGING AND STARTING,
REPAIRS, Battery.
11. LH side: Remove horn.

+ SECURITY, REPAIRS, Horn.
12. LH side: Remove air intake hose.
13. RH side: Remove front bumper RH support
bracket.
14. RH side: Remove windscreen washer
reservoir.

+ WIPERS AND WASHERS, REPAIRS,
Reservoir - washer.
15. RH side: Remove PAS fluid cooler.

+ STEERING, REPAIRS, Oil cooler -
Td4 & K1.8 models.Repair
1.Remove existing panel(s), prepare panel joint
faces and install new panel(s) in accordance
with Panel Replacement Procedure. Punch or
drill holes in new panel for plug welding as
shown.
Refit
1. LH side: Fit air intake hose.
2. LH side: Fit horn.
3. LH side: Fit battery. Do not connect earth lead.

+ CHARGING AND STARTING,
REPAIRS, Battery.
4. LH side: Fit front bumper LH support bracket.
5. RH side: Fit PAS fluid cooler.

+ STEERING, REPAIRS, Oil cooler -
Td4 & K1.8 models.
6. RH side: Fit windscreen washer reservoir.

+ WIPERS AND WASHERS, REPAIRS,
Reservoir - washer.
7. RH side: Fit front bumper LH support bracket.
8.Fit headlamp assembly.

+ LIGHTING, REPAIRS, Headlamp
assembly - up to 04MY.Secure headlamp
wiring.
9.Fit radiator.

+ COOLING SYSTEM - K SERIES KV6,
REPAIRS, Radiator assembly.
10.Fit front bumper armature.
11.Fit front bumper valance.

+ EXTERIOR FITTINGS, REPAIRS,
Bumper - assembly - front - up to 04MY.
12.Connect all ECUs.
13.Connect alternator.
14.Connect battery earth lead.

PANEL REPAIRS
77-2-30 REPAIRS
Front sidemember (complete)
In this procedure, the front sidemember closing
panel and the related crossmember to sidemember
gusset plate are replaced in conjunction with the front
sidemember.
Remove
1.Disconnect battery earth lead.
2.Disconnect alternator.
3.Disconnect all ECUs.
4.Remove road wheel(s).
5.Remove underbelly panel.

+ EXTERIOR FITTINGS, REPAIRS,
Panel - underbelly.
6.Remove front bumper valance.

+ EXTERIOR FITTINGS, REPAIRS,
Bumper - assembly - front - up to 04MY.
7.Remove front bumper armature.
8.Remove radiator.

+ COOLING SYSTEM - K SERIES KV6,
REPAIRS, Radiator assembly.
9.Remove PAS fluid cooler.

+ STEERING, REPAIRS, Oil cooler -
Td4 & K1.8 models.
10.Remove headlamp.

+ LIGHTING, REPAIRS, Headlamp
assembly - up to 04MY.
11.Release wiring to headlamp and position aside.
12.Remove engine bay shield.
13.Remove front wheel arch liner.

+ EXTERIOR FITTINGS, REPAIRS,
Liner - front wheel arch.
14.Remove front suspension rear beam.
15.Remove engine and gearbox.

+ ENGINE - K SERIES KV6, REPAIRS,
Engine and automatic gearbox - up to 03MY.
16.Remove PAS rack.

+ STEERING, REPAIRS, Power
steering rack.
17.Remove fascia.

+ INTERIOR TRIM COMPONENTS,
REPAIRS, Fascia - up to 04MY.
18. LH side: Remove front bumper LH support
bracket.
19. LH side: Remove LH engine mounting from
body.
20. LH side: Remove battery.

+ CHARGING AND STARTING,
REPAIRS, Battery.
21. LH side: Remove air intake hose.
22. LH side: Remove horn.

+ SECURITY, REPAIRS, Horn.
23. RH side: Remove front bumper RH support
bracket.24. RH side: Remove RH engine mounting from
body.
25. RH side: Remove windscreen washer
reservoir.

+ WIPERS AND WASHERS, REPAIRS,
Reservoir - washer.
26. Driver's side: Remove passenger
compartment fuse box.
27. Driver's side: Remove brake pedal box and
brake servo.
28. Driver's side: Remove clutch pedal box.
29.Remove treadplate from front door aperture.
Release front carpet and position aside.
30.Remove insulation pads from engine bulkhead.