charging LAND ROVER FREELANDER 2001 Repair Manual

AIR CONDITIONING
82-16REPAIRS
Evaporator
$% 82.25.20
Remove
1.Depressurise A/C system.

+ AIR CONDITIONING, REFRIGERANT
RECOVERY, RECYCLING AND
RECHARGING, Refrigerant recovery -
recycling and recharge.
2.Remove bolt securing pipes to TXV valve.
3.Release both pipes from TXV valve.
4.Remove and discard 2 'O' rings from pipes.
CAUTION: Immediately cap all A/C pipes to
prevent ingress of dirt and moisture into the
system.
5.Remove fascia.

+ INTERIOR TRIM COMPONENTS,
REPAIRS, Fascia - up to 04MY.
6.Remove bolt from face level ducting and
remove ducting.7.Disconnect 3 multiplugs from A/C switches and
heater harness.
8.Remove 2 nuts securing evaporator to body.
9.Release evaporator from drain hose and air
intake, remove evaporator assembly.
10.Release harness from evaporator securing
clips.
11.Remove 7 screws from evaporator casing and
remove top half of casing.
M820798
M820824

AIR CONDITIONING
REPAIRS 82-17
12.Remove evaporator from casing.
13.Remove 2 Allen key bolts securing TXV valve,
remove valve and discard 2 'O' rings.
Refit
1.Lubricate new 'O' rings with clean refrigerant oil
and fit to evaporator pipes
2.Fit evaporator pipes to TXV valve and fit
bracket, fit and tighten bolt to 10 Nm (7 lbf.ft).
3.Carefully fit evaporator to casing.
4.Fit top half of evaporator casing.
5.Fit 7 screws to casing.
6.Fit harness in securing clips.
7.Locate evaporator assembly to drain hose and
air intake, position evaporator to body.
8.Fit and tighten nuts securing evaporator to
body.
9.Connect multiplugs to heater harness and A/C
switches.
10.Position face level vent ducting, fit and tighten
bolt.
11.Fit fascia.

+ INTERIOR TRIM COMPONENTS,
REPAIRS, Fascia - up to 04MY.
12.Clean evaporator pipes.
13.Lubricate new 'O' rings with refrigerant oil.
14.Fit 'O' rings to evaporator pipes.
15.Clean evaporator pipes.
16.Fit pipes to TXV valve and fit bracket, tighten
bolt to 10 Nm (7 lbf.ft).
17.Charge A/C system.

+ AIR CONDITIONING, REFRIGERANT
RECOVERY, RECYCLING AND
RECHARGING, Refrigerant recovery -
recycling and recharge.
M820825

CHARGING AND STARTING
ADJUSTMENTS 86-1-1
CHARGING AND STARTING ADJUST ME NTS
Ancillary drive belt - K1.8
$% 86.10.05
Check
1.Disconnect battery earth lead.
2.Turn steering on RH lock.
3.Remove 3 bolts and remove splash shield.
4.Rotate crankshaft a sufficient number of turns
to check condition of drive belt. Renew a drive
belt that shows signs of wear, splitting or oil
contamination.
5.Apply a force of 10 kg to drive belt at position 'X'
and measure deflection between crankshaft
pulley and alternator pulley. Deflection must be
6 - 8 mm.Adjust
1.Loosen alternator pivot nut and bolt.
2.Loosen bolt securing alternator adjustment
bracket to engine.
3.Loosen bolt securing alternator to adjustment
bracket.
4.Increase drive belt tension by rotating
alternator adjustment bolt clockwise.
5.Tighten alternator pivot and adjustment bracket
bolts to 25 Nm (18 lbf.ft).
6.Recheck drive belt tension.
7.Fit splash shield and secure with bolts.
8.Straighten steering.
9.Connect battery earth lead.

CHARGING AND STARTING
86-1-2 ADJUSTMENTS
Ancillary drive belt - K1.8 with A/C
$% 86.10.05
Check
1.Disconnect battery earth lead.
2.Turn steering on RH lock.
3.Remove 3 bolts and remove splash shield.
4.Rotate crankshaft a sufficient number of turns
to check condition of drive belt. Renew a drive
belt that shows signs of wear, splitting or oil
contamination.
5.Check belt length, belt must be renewed before
indicator reaches RH end of slot.
6.Fit splash shield and secure with bolts.
7.Straighten steering.
8.Connect battery earth lead.

CHARGING AND STARTING
REPAIRS 86-1-3
REPAIRS
Alternator - Td4
$% 86.10.02
Remove
1.Disconnect battery earth lead.
2.Drain cooling system.

+ COOLING SYSTEM - Td4,
ADJUSTMENTS, Coolant - drain and refill.
3. Models with A/C: Remove compressor drive
belt.

+ AIR CONDITIONING, REPAIRS,
Drive belt - compressor - Td4.
4.Remove 3 bolts securing coolant rail to sump
and cylinder block.
CAUTION: Care must be taken to ensure
that oil or fluid does not enter or
contaminate the alternator.
5. Models with A/C: Loosen bolt securing
compressor support bracket to sump, do not
remove.
6. Models with A/C: Remove 3 bolts securing
compressor to mounting bracket, release
support bracket and tie compressor aside.7. Models with A/C: Remove 3 bolts and bracket,
securing compressor mounting to casting on
cylinder block.
8.Disconnect alternator multiplug.
9.Remove nut securing battery cable to alternator
and remove cable.
10.Remove 3 bolts and remove alternator.
M86 5309
M86 5311

CHARGING AND STARTING
86-1-4 REPAIRS
Refit
1.Clean alternator mounting points.
2.Fit alternator to mounting bracket.Tighten M10
bolt to 45 Nm (33 lbf.ft) and M8 bolts to 25 Nm
(18 lbf.ft).
CAUTION: Ensure upper bolt is fitted prior
to assembly.
3.Connect alternator multiplug.
4.Fit battery cable to alternator terminal and
tighten to 10 Nm (7.5 lbf.ft).
5. Models with A/C: Clean A/C compressor and
housing mating faces, dowels and dowel holes.
6. Models with A/C: Fit bolts and compressor
mounting to casting, tighten to 25 Nm (18 lbf.ft).
7. Models with A/C: Position A/C compressor, fit
bolts and tighten to 25 Nm (18 lbf.ft).
8. Models with A/C: Align compressor support
bracket to sump and tighten bolt to 10 Nm (7.5
lbf.ft).
9.Fit lower coolant rail to sump and tighten bolts
to 10 Nm (7.5 lbf.ft).
10.Fit compressor drive belt.

+ AIR CONDITIONING, REPAIRS,
Drive belt - compressor - Td4.
11.Refill cooling system.

+ COOLING SYSTEM - Td4,
ADJUSTMENTS, Coolant - drain and refill.
12.Connect battery earth lead.

CHARGING AND STARTING
REPAIRS 86-1-5
Alternator - KV6
$% 86.10.02
Remove
1.Disconnect battery earth lead.
2.Remove top arm.

+ ENGINE - K SERIES KV6, REPAIRS,
Arm assembly - engine mounting RH.
3.Using a 3/8” square drive socket bar, raise
ancillary drive belt tensioner and release drive
belt from alternator pulley.
4.Release alternator battery lead terminal cover,
loosen terminal nut and disconnect lead from
terminal
5.Disconnect alternator multiplug.
6.Remove lower bolt and upper nut and bolt
securing alternator to front mounting plate.
7.Remove alternator.Refit
1.Position alternator to front mounting plate.
2.Fit bolt and nut and bolt securing alternator to
front mounting plate and tighten to 45 Nm (33
lbf.ft).
3.Using a 3/8” square drive socket bar, raise
ancillary drive belt tensioner and fit drive belt to
pulleys.
4.Connect alternator multiplug.
5.Position battery cable to alternator, tighten nut
to 10 Nm (7.5 lbf.ft) and position terminal
cover.
6.Fit top arm.

+ ENGINE - K SERIES KV6, REPAIRS,
Arm assembly - engine mounting RH.
7.Connect battery earth lead.

CHARGING AND STARTING
86-1-6 REPAIRS
Alternator - K1.8
$% 86.10.02
Remove
1.Disconnect battery earth lead.
2.Remove exhaust manifold heat shield.

+ MANIFOLDS & EXHAUST SYSTEMS
- K SERIES 1.8, REPAIRS, Heat shield -
exhaust manifold - with A/C.
3.Remove bolt securing alternator mounting
bracket. Rotate bracket clear of alternator and
remove bracket.
4.Release cover from battery lead on alternator.
5.Loosen nut securing battery lead to alternator
and release lead.
6.Disconnect multiplug from alternator.
7.Remove nut and bolt from alternator lower
mounting bracket.
8.Remove alternator from mounting bracket.Refit
1.Position alternator to mounting bracket.
2.Fit lower nut and bolt securing alternator but do
not tighten at this stage.
3.Connect multiplug and position battery cable to
alternator and tighten nut.
4.Position battery lead cover.
5.Fit alternator mounting bracket, tighten bolts to
25 Nm (18 lbf.ft).
6.Fit exhaust manifold heat shield.

+ MANIFOLDS & EXHAUST SYSTEMS
- K SERIES 1.8, REPAIRS, Heat shield -
exhaust manifold - with A/C.
7.Connect battery earth lead.
M86 5388

CHARGING AND STARTING
REPAIRS 86-1-7
Ancillary drive belt - Td4
$% 86.10.03
Remove
1.Disconnect battery earth lead.
2.Remove engine acoustic cover if fitted.

+ ENGINE - Td4, REPAIRS, Cover -
engine acoustic - Up to 02.5 Model Year.
3.Remove underbelly panel.

+ EXTERIOR FITTINGS, REPAIRS,
Panel - underbelly.
4.Turn steering on RH lock.
5.Remove 3 bolts and RH splash shield.
6.Position LRT-12-163 to ancillary drive belt
tensioner, turn tensioner anti-clockwise and
release ancillary drive belt from pulleys.
7.Remove ancillary drive belt.Refit
1.Ensure pulleys are clean and damage free.
CAUTION: Examine drive belt for signs of
wear. A drive belt with cracked ribs is
acceptable. A drive belt that has loose or
missing parts of ribs must be changed.
2.Use LRT-12-163 to hold belt tensioner off and
with assistance, fit ancillary belt. Ensure belt is
correctly located in pulley grooves.
3.Fit splash shield and tighten bolts to 10 Nm (7
lbf.ft).
4.Fit underbelly panel.

+ EXTERIOR FITTINGS, REPAIRS,
Panel - underbelly.
5.Fit engine acoustic cover if fitted.

+ ENGINE - Td4, REPAIRS, Cover -
engine acoustic - Up to 02.5 Model Year.
6.Connect battery earth lead.
M86 5290A
LRT-12-163

CHARGING AND STARTING
86-1-8 REPAIRS
Ancillary drive belt - K1.8 without A/C
$% 86.10.03
Remove
1.Disconnect battery earth lead.
2.Remove PAS pump drive belt.

+ STEERING, REPAIRS, Drive belt -
K1.8.
3.Loosen alternator pivot nut and bolt.
4.Loosen bolt securing alternator adjustment
bracket to engine.
5.Loosen bolt securing alternator to adjustment
bracket.
6.Rotate alternator drive belt adjustment bolt anti-
clockwise to release tension from belt and
remove belt.Refit
1.Ensure pulleys are clean and damage free.
CAUTION: Examine drive belt for signs of
wear. A drive belt with cracked ribs is
acceptable. A drive belt that has loose or
missing parts of ribs must be changed.
2.Fit drive belt. Ensure belt is located correctly in
pulley grooves.
3.Adjust belt tension.

+ CHARGING AND STARTING,
ADJUSTMENTS, Ancillary drive belt - K1.8.
4.Fit PAS pump drive belt.

+ STEERING, REPAIRS, Drive belt -
K1.8.
5.Connect battery earth lead.