power steering LAND ROVER FREELANDER 2001 Owner's Manual

STEERING
57-14 REPAIRS
Pump - steering - K1.8
$% 57.20.14
Remove
1.Disconnect battery earth lead.
2.Raise front of vehicle.
WARNING: Do not work on or under a
vehicle supported only by a jack. Always
support the vehicle on safety stands.
3.Loosen PAS pump pulley bolts.
4.Remove PAS pump drive belt.

+ STEERING, REPAIRS, Drive belt -
K1.8.
5.Position container to collect PAS fluid spillage.
6.Release clip and disconnect fluid inlet hose
from PAS pump.
CAUTION: Always fit plugs to open
connections to prevent contamination.
7.Loosen union securing fluid outlet pipe, release
outlet pipe remove and discard 'O' ring.
8.Remove 3 bolts securing PAS pump pulley to
PAS pump and remove pulley.9.Remove 5 bolts securing PAS pump to
mounting bracket.
10.Remove PAS pump.
Refit
1.Position PAS pump and align to mounting
bracket.
2.Fit bolts securing PAS pump to mounting
bracket and tighten to 25 Nm (18 lbf.ft).
3.Fit PAS pump pulley and align bolts holes.
Ensure FRONT mark is facing outwards. Fit
bolts finger tight.
4.Remove plug from fluid outlet hose.
5.Clean PAS pump and pipe union.
6.Using a new 'O' ring, align outlet pipe and
tighten union to 20 Nm (15 lbf.ft).
7.Clean elbow on PAS pump.
8.Remove plug from fluid inlet hose, fit new clip
and connect hose to PAS pump.
9.Remove container.
10.Clean pulley 'V's and tensioner pulley running
surface.
11.Fit PAS pump drive belt.

+ STEERING, REPAIRS, Drive belt -
K1.8.
12.Tighten PAS pump pulley bolts to 10 Nm (7.5
lbf.ft).
13.Connect battery earth lead.
14.Bleed PAS system.

+ STEERING, ADJUSTMENTS, Power
assisted steering (PAS) system - bleed.
M57 1069
M57 1070

STEERING
57-24 REPAIRS
Track rod
$% 57.55.09
Remove
1. Td4 & KV6 models: Remove steering rack.

+ STEERING, REPAIRS, Power
steering rack.
2.Remove Torx bolt securing track rod to PAS
rack. Discard Torx bolt.
3.Remove track rod and spacer.
CAUTION: Note orientation of spacers
before dismantling.
4.Hold track rod securely and loosen pinch bolt in
track rod end.
NOTE: Do not carry out further dismantling if
component is removed for access only.
5.Remove ball joint, note the number of turns for
refit.
6. Remove pinch bolt from track rod.
7.Remove turnbuckle and note the number of
turns for refit.
NOTE: Thread is left handed.Refit
1.Fit turnbuckle to track rod to number of turns on
remove.
2.Fit pinch bolt but do not tighten at this stage.
3.Fit ball joint to turnbuckle to number of turns
noted in remove.
4.Fit pinch bolt but do not tighten at this stage.
CAUTION: Ensure slots in turn buckle
clamps are aligned.
5.Clean spacer, support plate and track rod ball
joint.
6.Fit spacer to rack.
CAUTION: Ensure spacers are aligned and
fitted correctly.
7.Fit track rod to PAS rack.
8.Hold track rod parallel to PAS rack, fit new Torx
bolt and tighten to 100 Nm (74 lbf.ft).
9. Td4 & KV6 models: Fit steering rack.

+ STEERING, REPAIRS, Power
steering rack.
10.Check and adjust front wheel alignment.

+ STEERING, ADJUSTMENTS, Front
wheel alignment - check & adjust.
WARNING: Ensure all track rod pinch bolts
are tightened to the correct torque on
completion of the front wheel alignment
check.

PANEL REPAIRS
77-2-30 REPAIRS
Front sidemember (complete)
In this procedure, the front sidemember closing
panel and the related crossmember to sidemember
gusset plate are replaced in conjunction with the front
sidemember.
Remove
1.Disconnect battery earth lead.
2.Disconnect alternator.
3.Disconnect all ECUs.
4.Remove road wheel(s).
5.Remove underbelly panel.

+ EXTERIOR FITTINGS, REPAIRS,
Panel - underbelly.
6.Remove front bumper valance.

+ EXTERIOR FITTINGS, REPAIRS,
Bumper - assembly - front - up to 04MY.
7.Remove front bumper armature.
8.Remove radiator.

+ COOLING SYSTEM - K SERIES KV6,
REPAIRS, Radiator assembly.
9.Remove PAS fluid cooler.

+ STEERING, REPAIRS, Oil cooler -
Td4 & K1.8 models.
10.Remove headlamp.

+ LIGHTING, REPAIRS, Headlamp
assembly - up to 04MY.
11.Release wiring to headlamp and position aside.
12.Remove engine bay shield.
13.Remove front wheel arch liner.

+ EXTERIOR FITTINGS, REPAIRS,
Liner - front wheel arch.
14.Remove front suspension rear beam.
15.Remove engine and gearbox.

+ ENGINE - K SERIES KV6, REPAIRS,
Engine and automatic gearbox - up to 03MY.
16.Remove PAS rack.

+ STEERING, REPAIRS, Power
steering rack.
17.Remove fascia.

+ INTERIOR TRIM COMPONENTS,
REPAIRS, Fascia - up to 04MY.
18. LH side: Remove front bumper LH support
bracket.
19. LH side: Remove LH engine mounting from
body.
20. LH side: Remove battery.

+ CHARGING AND STARTING,
REPAIRS, Battery.
21. LH side: Remove air intake hose.
22. LH side: Remove horn.

+ SECURITY, REPAIRS, Horn.
23. RH side: Remove front bumper RH support
bracket.24. RH side: Remove RH engine mounting from
body.
25. RH side: Remove windscreen washer
reservoir.

+ WIPERS AND WASHERS, REPAIRS,
Reservoir - washer.
26. Driver's side: Remove passenger
compartment fuse box.
27. Driver's side: Remove brake pedal box and
brake servo.
28. Driver's side: Remove clutch pedal box.
29.Remove treadplate from front door aperture.
Release front carpet and position aside.
30.Remove insulation pads from engine bulkhead.

PANEL REPAIRS
REPAIRS 77-2-31
Repair
1.Remove existing panel(s), prepare panel joint
faces and install new panel(s) in accordance
with Panel Replacement Procedure. Punch or
drill holes in new panel for plug welding as
shown.
Refit
1.Fit insulation pads to engine bulkhead.
2.Position front carpet and fit treadplate to front
door aperture. 3. Driver's side: Fit clutch pedal box.
4. Driver's side: Fit brake pedal box and brake
servo.
5. Driver's side: Fit passenger compartment fuse
box.
6. LH side: Fit horn.

+ SECURITY, REPAIRS, Horn.
7. LH side: Fit air intake hose.
8. LH side: Fit battery. Do not connect battery
earth lead.

+ CHARGING AND STARTING,
REPAIRS, Battery.
9. LH side: Fit LH engine mounting to body.
10. LH side: Fit front bumper LH support bracket.
11. RH side: Fit windscreen washer reservoir.

+ WIPERS AND WASHERS, REPAIRS,
Reservoir - washer.
12. RH side: Fit RH engine mounting to body.
13. RH side: Fit front bumper RH support bracket.
14.Fit fascia.

+ INTERIOR TRIM COMPONENTS,
REPAIRS, Fascia - up to 04MY.
15.Fit PAS rack.

+ STEERING, REPAIRS, Power
steering rack.
16.Fit engine and gearbox.

+ ENGINE - K SERIES KV6, REPAIRS,
Engine and automatic gearbox - up to 03MY.
17.Fit front suspension rear beam.
18.Fit front wheel arch liner.

+ EXTERIOR FITTINGS, REPAIRS,
Liner - front wheel arch.
19.Fit engine bay shield.
20.Fit headlamp.

+ LIGHTING, REPAIRS, Headlamp
assembly - up to 04MY.
21.Secure headlamp wiring.
22.Fit PAS fluid cooler.

+ STEERING, REPAIRS, Oil cooler -
Td4 & K1.8 models.
23.Fit radiator.

+ COOLING SYSTEM - K SERIES KV6,
REPAIRS, Radiator assembly.
24.Fit front bumper armature.
25.Fit front bumper valance.

+ EXTERIOR FITTINGS, REPAIRS,
Bumper - assembly - front - up to 04MY.
26.Fit underbelly panel.

+ EXTERIOR FITTINGS, REPAIRS,
Panel - underbelly.
27.Fit road wheel(s) and tighten nuts to 115 Nm
(85 lbf.ft).
28.Connect all ECUs.
29.Connect alternator.
30.Connect battery earth lead.

PANEL REPAIRS
REPAIRS 77-2-33
Refit
1. LH side: Fit horn.

+ SECURITY, REPAIRS, Horn.
2. LH side: Fit air intake hose.
3. LH side: Fit air cleaner.
4. LH side: Fit battery carrier. Do not connect
battery earth lead.

+ CHARGING AND STARTING,
REPAIRS, Carrier - battery.
5. LH side: Fit ECM.
6. LH side: Fit front bumper LH support bracket.
7. RH side: Fit PAS pump.

+ STEERING, REPAIRS, Pump -
steering - KV6.
8. RH side: Fit alternator.

+ CHARGING AND STARTING,
REPAIRS, Alternator - KV6.
9. RH side: Fit windscreen washer reservoir.

+ WIPERS AND WASHERS, REPAIRS,
Reservoir - washer.
10. RH side: Fit front bumper RH support bracket.
11.Fit front wheel arch liner.

+ EXTERIOR FITTINGS, REPAIRS,
Liner - front wheel arch.
12.Fit engine bay shield.
13.Fit headlamp.

+ LIGHTING, REPAIRS, Headlamp
assembly - up to 04MY.
14. Secure headlamp wiring.
15.Fit PAS fluid cooler.

+ STEERING, REPAIRS, Oil cooler -
Td4 & K1.8 models.
16.Fit radiator.

+ COOLING SYSTEM - K SERIES KV6,
REPAIRS, Radiator assembly.
17.Fit front bumper valance.

+ EXTERIOR FITTINGS, REPAIRS,
Bumper - assembly - front - up to 04MY.
18.Fit underbelly panel.

+ EXTERIOR FITTINGS, REPAIRS,
Panel - underbelly.
19.Connect all ECUs.
20.Connect battery earth lead.
Front valance assembly
Remove
1.Disconnect battery earth lead.
2.Disconnect all ECUs.
3.Remove road wheel(s).
4.Remove underbelly panel.

+ EXTERIOR FITTINGS, REPAIRS,
Panel - underbelly.
5.Remove front bumper valance.

+ EXTERIOR FITTINGS, REPAIRS,
Bumper - assembly - front - up to 04MY.
6.Remove front bumper armature.
7.Remove radiator.

+ COOLING SYSTEM - K SERIES KV6,
REPAIRS, Radiator assembly.
8.Remove PAS fluid cooler.

+ STEERING, REPAIRS, Oil cooler -
Td4 & K1.8 models.
9.Remove headlamp.

+ LIGHTING, REPAIRS, Headlamp
assembly - up to 04MY.
10.Release wiring to headlamp and position aside.
11.Remove engine bay shield.
12.Remove front wheel arch liner.

+ EXTERIOR FITTINGS, REPAIRS,
Liner - front wheel arch.
13.Remove front wing.

+ EXTERIOR FITTINGS, REPAIRS,
Wing - front.
14.Remove front suspension rear beam.
15.Remove engine and gearbox.

+ ENGINE - K SERIES KV6, REPAIRS,
Engine and automatic gearbox - up to 03MY.
16.Remove front damper.

+ FRONT SUSPENSION, REPAIRS,
Damper.
17.Remove PAS rack.

+ STEERING, REPAIRS, Power
steering rack.
18.Remove fascia.

+ INTERIOR TRIM COMPONENTS,
REPAIRS, Fascia - up to 04MY.
19. LH side: Remove front bumper LH support
bracket.
20. LH side: Remove air cleaner.
21. LH side: Remove air intake hose.
22. LH side: Remove ECM.
23. LH side: Remove engine compartment
fusebox.
24. LH side: Remove battery carrier.

+ CHARGING AND STARTING,
REPAIRS, Carrier - battery.
25. LH side: Remove engine compartment fuse
box and related wiring.

PANEL REPAIRS
77-2-34 REPAIRS
26. LH side: Remove LH engine mounting from
body.
27. LH side: On models with Diesel engines,
remove fuel filter.

+ FUEL DELIVERY SYSTEM - DIESEL,
REPAIRS, Filter - main - up to 03MY.
28. LH side: Remove LH front brake pipe.
29. RH side: Remove front bumper RH support
bracket.
30. RH side: Remove windscreen washer
reservoir.

+ WIPERS AND WASHERS, REPAIRS,
Reservoir - washer.
31. RH side: Remove coolant expansion tank.
32. RH side: Remove RH engine mounting from
body.
33. RH side: Remove PAS fluid reservoir.
34. RH side: Remove RH front brake pipe.
35. Driver's side: Remove passenger
compartment fuse box.
36.Remove brake pedal box and brake servo.
37.Remove clutch pedal box.
38.Release vehicle harness from valance and
position aside.
39.Remove treadplate from front door aperture.
Release front carpet and position aside.
40.Remove insulation pads from engine bulkhead.
Repair
1.Remove existing panel(s), prepare panel joint
faces and install new panel(s) in accordance
with Panel Replacement Procedure. Punch or
drill holes in new panel for plug welding as
shown. Refit
1.Fit insulation pads to front and rear sides of
engine bulkhead.
2.Position front carpet and fit treadplate to front
door aperture.
3.Secure vehicle harness to valance.
4. Driver's side: Fit clutch pedal box.
5.Fit brake pedal box and brake servo.
6.Fit passenger compartment fuse box.
7. LH side: Fit LH front brake pipe. Bleed brake
system.
+ BRAKES, ADJUSTMENTS, Brake
bleed.
8. LH side: On models with Diesel engines, fit fuel
filter.

+ FUEL DELIVERY SYSTEM - DIESEL,
REPAIRS, Filter - main - up to 03MY.
9. LH side: Fit LH engine mounting to body.
10. LH side: Fit engine compartment fuse box and
related wiring.
11. LH side: Fit battery carrier. Do not connect
battery earth lead.

+ CHARGING AND STARTING,
REPAIRS, Carrier - battery.
12. LH side: Fit engine compartment fusebox.
13. LH side: Fit ECM.
14. LH side: Fit air intake hose.
15. LH side: Fit air cleaner.
16. LH side: Fit front bumper LH support bracket.
17. RH side: Fit RH front brake pipe. Bleed brake
system.

+ BRAKES, ADJUSTMENTS, Brake
bleed.
18. RH side: Fit PAS fluid reservoir.
19. RH side: Fit RH engine mounting to body.
20. RH side: Fit coolant expansion tank.
21. RH side: Fit windscreen washer reservoir.

+ WIPERS AND WASHERS, REPAIRS,
Reservoir - washer.
22. RH side: Fit front bumper RH support bracket.
23.Fit fascia.

+ INTERIOR TRIM COMPONENTS,
REPAIRS, Fascia - up to 04MY.
24.Fit PAS rack.

+ STEERING, REPAIRS, Power
steering rack.
25.Fit front damper.

+ FRONT SUSPENSION, REPAIRS,
Damper.
26.Fit engine and gearbox.

+ ENGINE - K SERIES KV6, REPAIRS,
Engine and automatic gearbox - up to 03MY.
27.Fit front suspension rear beam.
28.Fit front wing.

+ EXTERIOR FITTINGS, REPAIRS,
Wing - front.