ECU LAND ROVER FREELANDER 2001 Workshop Manual

DOORS
REPAIRS 76-1-21
8.Remove locking ring securing tweeter to trim
casing and remove tweeter.
9.Remove foam pad from sill button guide.
10.Release retainer and remove sill button guide.
11.Note the fitted position of the 2 long trim studs
and remove 9 trim studs from trim casing.
12.Release and remove locking ring securing door
pull to trim casing.
13.Remove 2 plastic rivets securing door pull to
trim casing and remove door pull.
NOTE: Plastic rivets are used for production
purposes only. Screws should be used to retain
all parts previously held in place with plastic
rivets.Refit
1.Fit door pull to trim casing and secure with
screws and locking ring.
2.Fit trim studs to casing.
3.Fit sill button guide to trim casing and secure
with retainer.
4.Fit foam pad to sill button guide.
5.Fit tweeter to trim casing and secure with
locking ring.
6.Fit and secure window lift switch and finisher to
trim casing.
7.Connect multiplugs to window lift switch and
door tweeter.
8.Position trim casing, align fasteners with holes
in door and press firmly into position.
9.Fit and tighten screws securing door pull to
door assembly.
10.Fit and secure door pull finisher to door pull.
11.Fit door release escutcheon to trim casing and
secure with screw.

DOORS
76-1-22 REPAIRS
Trim casing - tail door
$% 76.34.10
Remove
1.Remove 4 screws securing bottom of trim
casing to door.
2.Release 8 clips securing sides and bottom of
casing.
3.Release 5 clips securing top of casing and
remove casing.
4.Remove 8 trim studs from casing.Refit
1.Fit trim studs to casing.
2.Position casing and secure top clips.
3.Secure clips on sides and bottom of casing.
4.Fit screws to bottom of casing.

DOORS
REPAIRS 76-1-23
Plastic sheet - front door - lower - 3 door
$% 76.34.18
Remove
1.Remove front door pocket.

+ DOORS, REPAIRS, Pocket - front
door - 3 door.
2.Release and discard plastic sheet.
Refit
1.Clean door contact area with white spirit.
2.Position NEW plastic sheet to door and seal in
position, by applying hand pressure to centre
bottom of sheet first then move out from this
point in both directions applying an even
pressure to the seal, smooth out any creases.
3.Fit front door pocket.

+ DOORS, REPAIRS, Pocket - front
door - 3 door.
Pocket - front door - 3 door
$% 76.34.19
Remove
1.Remove 8 Torx screws securing pocket to door
and remove pocket.
Refit
1.Fit pocket and secure with Torx screws.
M76 4026

DOORS
REPAIRS 76-1-25
Plastic sheet - front door - 5 door
$% 76.34.26
Remove
1.Remove front door speaker.

+ IN CAR ENTERTAINMENT,
REPAIRS, Speaker - front.
2.Remove 5 door pocket screw fixings.
3.Remove 2 door handle screw fixings. 04MY:
Remove 1 additional screw.
4.Release and discard plastic sheet.
Refit
1.Clean door contact area with white spirit.
2.Position NEW plastic sheet to door and seal in
position, by applying hand pressure to centre
bottom of sheet first then move out from this
point in both directions applying an even
pressure to the seal, smooth out any creases.
CAUTION: It is crucial that no creases are
present along the base of the plastic sheet.
3.Fit and secure door handle and pocket fixings.
4.Fit front door speaker.

+ IN CAR ENTERTAINMENT,
REPAIRS, Speaker - front.
Plastic sheet - rear door
$% 76.34.28
Remove
1.Remove rear door speaker.

+ IN CAR ENTERTAINMENT,
REPAIRS, Speaker - rear - 5 door.
2.Noting their fitted position, remove 7 trim stud
retainers, 2 door pull screw retainers and 4
speaker screw retainers.
3.Release and discard plastic sheet.
Refit
1.Clean door contact area with white spirit.
2.Position NEW plastic sheet to door and seal in
position, by applying hand pressure to centre
bottom of sheet first then move out from this
point in both directions applying an even
pressure to the seal, smooth out any creases.
CAUTION: It is crucial that no creases are
present along the base of the plastic sheet.
3.Fit trim stud retainers and screw retainers to
door.
4.Fit rear door speaker.

+ IN CAR ENTERTAINMENT,
REPAIRS, Speaker - rear - 5 door.

DOORS
76-1-26 REPAIRS
Latch - front door - 3 door
$% 76.37.12
Remove
1.Remove upper plastic sheet.

+ DOORS, REPAIRS, Plastic sheet -
front door - upper - 3 door.
2.Release sill button lock rod from door latch.
3.Remove control rod from exterior handle.
4.Disconnect multiplug from latch.
5.Remove 3 Torx screws securing latch to door.
6.On drivers door, release door lock barrel
paddle from latch.
7.Remove latch from aperture.8.Open security flap on latch.
9.Release interior release cable clamp from
latch.
10.Disengage interior release cable from latch.
Refit
1.Secure interior release cable to latch and close
latch security flap.
2.Fit interior release cable clamp to latch.
3.Position latch to door. On drivers door, align
lock barrel paddle to latch.
4.Fit and tighten Torx screws securing latch to
door.
5.Connect multiplug to latch.
6.Connect exterior handle control rod to latch.
7.Fit sill button lock rod to latch.
8.Check operation of latch.
9.Fit plastic sheet to door.

+ DOORS, REPAIRS, Plastic sheet -
front door - upper - 3 door.

DOORS
REPAIRS 76-1-27
Latch - front door - 5 door
$% 76.37.12
Remove
1.Remove front door plastic sheet.

+ DOORS, REPAIRS, Plastic sheet -
front door - 5 door.
2.Release sill button lock rod from door latch.
3.Release control rod from exterior handle.
4.Disconnect multiplug from latch.
5.Remove 2 screws securing RH glass cable
guide and position guide aside.
6.Remove 3 Torx screws securing latch to door.
7.On drivers door, release door lock barrel
paddle from latch.8.Remove latch from aperture.
9.Open security flap on latch.
10.Release interior release cable clamp from
latch.
11.Disengage interior release cable from latch.
Refit
1.Secure interior release cable to latch and close
latch security flap.
2.Fit interior release cable clamp to latch.
3.Position latch to door. On drivers door, align
lock barrel paddle to latch.
4.Fit and tighten Torx screws securing latch to
door.
5.Position RH glass cable guide and tighten
screws.
6.Connect multiplug to door latch.
7.Connect exterior handle control rod to latch.
8.Fit sill button lock rod to latch.
9.Check operation of door latch.
10.Fit front door plastic sheet.

+ DOORS, REPAIRS, Plastic sheet -
front door - 5 door.

DOORS
76-1-28 REPAIRS
Latch - rear door
$% 76.37.13
Remove
1.Remove rear door plastic sheet.

+ DOORS, REPAIRS, Plastic sheet -
rear door.
2.Release exterior handle control rod from latch.
3.Release sill button lock rod from door latch.
4.Disconnect multiplug from latch.
5.Remove 3 Torx screws securing latch to door.
6.Remove latch from aperture.7.Open security flap on latch.
8.Release interior release cable clamp from
latch.
9.Disengage interior release cable from latch.
Refit
1.Secure interior release cable to latch and close
latch security flap.
2.Position latch to door, fit and tighten Torx
screws.
3.Connect multiplug to latch.
4.Connect exterior handle control rod to latch.
5.Fit sill button lock rod to latch.
6.Check operation of latch.
7.Fit rear door plastic sheet.

+ DOORS, REPAIRS, Plastic sheet -
rear door.

DOORS
REPAIRS 76-1-29
Latch - tail door
$% 76.37.16
Remove
1.Remove tail door plastic sheet.

+ DOORS, REPAIRS, Plastic sheet -
tail door.
2.Remove 4 screws securing door latch.
3.Release door latch to access harness clips and
multiplugs.
4.Disconnect 2 multiplugs from door latch.5.Release 2 door harness clips from latch.
6.Remove door latch.
7.Remove screw from solenoid motor and
remove motor from latch.
Refit
1.Position solenoid motor to latch, fit and tighten
screw.
2.Position door latch, connect multiplugs and
harness clips.
3.Locate door latch in position, fit and tighten
screws.
4.Fit tail door plastic sheet.

+ DOORS, REPAIRS, Plastic sheet -
tail door.

DOORS
76-1-30 REPAIRS
Remote control - front door
$% 76.37.31
Remove
1.Remove front door plastic sheet.

+ DOORS, REPAIRS, Plastic sheet -
front door - 5 door.
2.Drill out 2 rivets from door release.
3.Remove door release.
4.Release cable from door release.
Refit
1.Connect cable to door release.
2.Position door release and secure with rivets.
3.Fit front door plastic sheet.

+ DOORS, REPAIRS, Plastic sheet -
front door - 5 door.
Remote control - rear door
$% 76.37.32
Remove
1.Remove rear door plastic sheet.

+ DOORS, REPAIRS, Plastic sheet -
rear door.
2.Release cable from door release.
3.Drill out 2 rivets from door release.
4.Remove door release.
Refit
1.Connect cable to door release.
2.Position door release and secure with rivets.
3.Fit rear door plastic sheet.

+ DOORS, REPAIRS, Plastic sheet -
rear door.

DOORS
REPAIRS 76-1-31
Operating cable - lock remote control - 5
door
$% 76.37.60
Remove
1.Remove door latch.

+ DOORS, REPAIRS, Latch - front
door - 5 door.

+ DOORS, REPAIRS, Latch - rear door.
2.Release cable from interior door release and
remove cable.
Refit
1.Connect cable to interior door release.
2.Fit door latch.

+ DOORS, REPAIRS, Latch - front
door - 5 door.

+ DOORS, REPAIRS, Latch - rear door.
Finisher - rear screen - side - 5 door
$% 76.43.81
Remove
1.Open tail door.
2.Release tail door glass seal from aperture for
access to side finisher fixings.
3.Using a suitable trim stud removal tool, release
3 side finisher fixings from studs on body.
4.Remove side finisher from upper fixing.
5.Remove and discard fixings from finisher.
Refit
1.Fit NEW fixings to finisher.
2.Fit door glass seal to flange.
3.Fit finisher and secure fixings.