sensor Lexus CT200h 2013 (in English) User Guide

981-3. Theft deterrent system
CT200h_OM_OM76102E_(EE)
NOTICE
To ensure the intrusion sensor functions correctly
Installing accessories other than genuine Lexus parts or leaving objects
between the driver’s seat and front passenger’s seat may reduce the detection
performance.
To ensure that the sensors operate prop-
erly, do not touch or cover them.
Do not spray air fresheners or other prod-
ucts directly into the sensor holes.

1022. Instrument cluster
CT200h_OM_OM76102E_(EE)
*1: These lights turn on when the power switch is turned to ON mode to indicate
that a system check is being performed. They will turn off after the hybrid sys-
tem is on, or after a few seconds. There may be a malfunction in a system if
the lights do not turn on, or turn off. Have the vehicle inspected by any autho-
rized Lexus dealer or repairer, or another duly qualified and equipped profes-
sional.
*2: The light flashes to indicate a malfunction.
*3: This light illuminates on the center panel.
The indicators inform the driver of the operating state of the vehicle’s
various systems.
Indicators
Turn signal indicator
(P. 209)“ECO MODE” indica-
tor
(P. 265)
Tail light indicator
(P. 211)“SPORT MODE”
indicator (P. 265)
Headlight high beam
indicator (P. 212)
(if
equipped)
Cruise control indicator
(P. 228, 231)
(if
equipped)
Front fog light indicator
(P. 216)
(if
equipped)
Radar cruise control
indicator (P. 231)
Rear fog light indicator
(P. 216)
(if
equipped)
Lexus parking
assist-sensor indicator
(P. 245)
“READY” indicator
(P. 196)
*1, 2Slip indicator light
(P. 268, 271)
EV indicator (P. 79)
*1“TRC OFF” indicator
(P. 268)

109
2 2. Instrument cluster
Instrument cluster
CT200h_OM_OM76102E_(EE)
Multi-information display (with monochrome
display)

The multi-information display presents the driver with a variety of vehi-
cle data.
Energy monitor
Displays the status of the hybrid sys-
tem. (P. 117)
Drive information
Displays driving range, fuel con-
sumption and other cruising related
information. (P. 1 1 0 )
Setting
Changes instrument cluster display
settings (P. 650)
Lexus parking assist-sensor (if equipped)
Automatically displayed when the system is used (P. 245)
Dynamic radar cruise control display (if equipped)
Automatically displayed when the system is used (P. 231)
Warning messages
Automatically displayed when a malfunction occurs in one of the vehicle’s
systems (P. 575)
: If equipped
Display contents

1142. Instrument cluster
CT200h_OM_OM76102E_(EE)
Energy monitor
Displays the status of the hybrid system.(P. 1 1 7 )
Lexus parking assist-sensor (if equipped)
Automatically displayed when the system is used (P. 245)
The multi-information display is
operated using the meter control
switches.
Select an item/change pages
Enter/Set
Return to the previous screen
Press:
Displays the screen registered to
When no screen has been registered, the drive information screen will be dis-
played.
Press and hold:
Registers the currently displayed screen to (P. 650)
The registration confirmation screen is displayed. If the selected screen cannot
be registered, a registration failure message will be shown.
Operating the meter control switches
1
2
3
4

1323-2. Opening, closing and locking the doors
CT200h_OM_OM76102E_(EE)
Side doors
Smart entry & start system (vehicles with entry function)
Carry the electronic key to enable this function.
Grip the front door handle to
unlock the doors.
Make sure to touch the sensor on
the back of the handle.
The doors cannot be unlocked for
3 seconds after the doors are
locked.
Touch the lock sensor (inden-
tation on the upper part of the
front door handle) to lock the
doors.
Wireless remote control
Locks all the doors
Press and hold to close the win-
dows.*
Unlocks all the doors
Press and hold to open the win-
dows.
*
*
: These settings must be custom-
ized at any authorized Lexus
dealer or repairer, or another duly
qualified and equipped profes-
sional.
The vehicle can be locked and unlocked using the entry function, wire-
less remote control or door lock switch.
Locking and unlocking the doors from the outside
1
2
1
2

1333-2. Opening, closing and locking the doors
3
Operation of each component
CT200h_OM_OM76102E_(EE)
Operation signals
Doors:
The emergency flashers flash to indicate that the doors have been locked/
unlocked. (Locked: Once; Unlocked: Twice)
Windows:
A buzzer sounds to indicate that the windows are opening.
Security feature
If a door is not opened within approximately 30 seconds after the vehicle is
unlocked, the security feature automatically locks the vehicle again.
Welcome light illumination control
The front position, tail and license plate lights automatically turn on at night
when the doors are unlocked using the entry function or wireless remote control
if the light switch is in the “AUTO” position.
When the door cannot be locked by the lock sensor on the upper part of the door
handle (vehicles with entry function)
Door lock buzzer
If an attempt to lock the doors is made when a door is not fully closed, a buzzer
sounds continuously for 5 seconds. Fully close the door to stop the buzzer, and
lock the vehicle once more.
Setting the alarm (if equipped)
Locking the doors will set the alarm system. (P. 93)
If the smart entry & start system or the wireless remote control does not operate
properly
Use the mechanical key to lock and unlock the doors. (P. 621)
Replace the key battery with a new one if it is depleted. (P. 530) If the door will not lock even when the top-
side sensor area is touched, try touching
both the topside and underside sensor areas
at the same time.

1463-2. Opening, closing and locking the doors
CT200h_OM_OM76102E_(EE)
Note for the entry function
Even when the electronic key is within the effective range (detection areas), the
system may not operate properly in the following cases:
• The electronic key is too close to the window or outside door handle, near
the ground, or in a high place when the doors are locked or unlocked.
• The electronic key is near the ground or in a high place, or too close to the
rear bumper center when the back door is opened.
• The electronic key is on the instrument panel, luggage room, floor, or in the
door pockets or glove box when the hybrid system is started or power switch
modes are changed.
Do not leave the electronic key on top of the instrument panel or near the door
pockets when exiting the vehicle. Depending on the radio wave reception con-
ditions, it may be detected by the antenna outside the cabin and the door will
become lockable from the outside, possibly trapping the electronic key inside
the vehicle.
As long as the electronic key is within the effective range, the doors may be
locked or unlocked by anyone.
Even if the electronic key is not inside the vehicle, it may be possible to start
the hybrid system if the electronic key is near the window.
The doors may unlock if a large amount of water splashes on the door handle,
such as in the rain or in a car wash when the electronic key is within the effec-
tive range. (The door will automatically be locked after approximately 30 sec-
onds if the doors are not opened and closed.)
If the wireless remote control is used to lock the doors when the electronic key
is near the vehicle, there is a possibility that the door may not be unlocked by
the entry function. (Use the wireless remote control to unlock the doors.)
Touching the door lock sensor while wearing gloves may delay or prevent lock
operation. Remove the gloves and touch the lock sensor again.
If the door handle becomes wet while the electronic key is within the effective
range, the door may lock and unlock repeatedly. Place the key in a position 2 m
(6 ft.) or more separate from the vehicle while the vehicle is being washed.
(Take care to ensure that the key is not stolen.)
If the electronic key is inside the vehicle and a door handle becomes wet during
a car wash, a message may be shown on the multi-information display and a
buzzer will sound outside the vehicle. To turn off the alarm, lock all the doors.
The lock sensor may not work properly if it comes into contact with ice, snow,
mud, etc. Clean the lock sensor and attempt to operate it again, or use the lock
sensor on the lower part of the door handle.

1733-4. Adjusting the steering wheels and mirrors
3
Operation of each component
CT200h_OM_OM76102E_(EE)
Auto anti-glare inside rear view mirror
Responding to the level of brightness of the headlights of vehicles behind,
the reflected light is automatically reduced.
Changing automatic anti-glare
function mode
On/off
When the automatic anti-glare func-
tion is in ON mode, the indicator
illuminates.
The function will set to ON mode
each time the power switch is turned
to ON mode.
Pressing the button turns the func-
tion to OFF mode. (The indicator
also turns off.)
To prevent sensor error (vehicles with auto anti-glare inside rear view mirror)
Indicator
To ensure that the sensors operate properly,
do not touch or cover them.
WA R N I N G
Do not adjust the position of the mirror while driving.
Doing so may lead to mishandling of the vehicle and cause an accident, result-
ing in death or serious injury.

185
4Driving
CT200h_OM_OM76102E_(EE)
4-1. Before driving
Driving the vehicle............ 186
Cargo and luggage ............ 194
Trailer towing.................... 195
4-2. Driving procedures
Power (ignition) switch ..... 196
EV drive mode .................. 201
Hybrid transmission .......... 203
Turn signal lever ............... 209
Parking brake .................... 2104-3. Operating the lights
and wipers
Headlight switch ................211
Fog light switch ................ 216
Windshield wipers and
washer ............................. 218
Rear window wiper and
washer ............................. 222
Headlight cleaner switch .. 223
4-4. Refueling
Opening the fuel tank cap . 224
4-5. Using the driving support
systems
Cruise control ................... 228
Dynamic radar cruise
control ............................. 231
Lexus parking
assist-sensor .................... 245
Rear view monitor system 253
Driving mode select
switch.............................. 265
Driving assist systems ...... 266
Hill-start assist control ...... 271
PCS (Pre-Crash Safety
system)............................ 273
4-6. Driving tips
Hybrid vehicle driving tips 281
Winter driving tips ............ 284

2144-3. Operating the lights and wipers
CT200h_OM_OM76102E_(EE)
Daytime running light system
To make your vehicle more visible to other drivers, the front position lights turn
on automatically (at an increased intensity) whenever the hybrid system is started
and the parking brake is released. Daytime running lights are not designed for
use at night.
Headlight control sensor
Automatic light off system
When the light switch is in the or position: The headlights turn off
automatically if the power switch is turned to ACCESSORY mode or OFF.
When the light switch is in the position: The headlights and all lights turn
off automatically if the power switch is turned to ACCESSORY mode or OFF.
To turn the lights on again, turn the power switch to ON mode, or turn the light
switch off once and then back to the
or position.
Automatic headlight leveling system (if equipped)
The level of the headlights is automatically adjusted according to the number of
passengers and the loading condition of the vehicle to ensure that the headlights
do not interfere with other road users.
Light reminder buzzer (if equipped)
A buzzer sounds when the power switch is turned off or turned to ACCESSORY
mode and the driver’s door is opened while the lights are turned on. The sensor may not function properly if an
object is placed on the sensor, or anything
that blocks the sensor is affixed to the wind-
shield.
Doing so interferes with the sensor detect-
ing the level of ambient light and may cause
the automatic headlight system to malfunc-
tion.