lock Lexus ES300 1994 In Case Of An Emergency

SECTION 4
131
IN CASE OF AN EMERGENCY
If your engine stalls while driving132 . . . . . . . . . . . . . . . . . . . . . . . . . . .
If your vehicle will not start132 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
If your vehicle overheats134 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
If you have a flat tire135 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
If your vehicle needs to be towed140 . . . . . . . . . . . . . . . . . . . . . . . . . .
If you cannot shift the automatic transmission selector lever143 . . .
If you lose your keys or lock yourself out144 . . . . . . . . . . . . . . . . . . . .

IN CASE OF AN EMERGENCY
137
Flat tire
Wheel block
3. Block the wheel diagonally opposite the flat tire to keep
the vehicle from rolling when it is jacked up.
When blocking the wheel, place a wheel block in front of the
front wheels or behind the rear wheels.
4. Loosen all the wheel nuts.Always loosen the wheel nuts before raising the vehicle.
Turn the nuts counterclockwise to loosen. To get maximum
leverage, fit the wrench to the nut so that the handle is on the
right side, as shown above. Grab the wrench near the end of
the handle and pull up on the handle. Be careful that the
wrench does not slip off the nut.
Do not remove the nuts yet-just unscrew them about one-half
turn.
5. Position the jack at the jack points shown.
Make sure the jack is positioned on a level and solid surface.

IN CASE OF AN EMERGENCY
138
6. After making sure no one is in the vehicle, raise it high
enough so that the spare tire can be installed.
Allow for the fact that you need more ground clearance when
putting on the spare tire than when removing the flat tire.
To raise the vehicle, insert the jack handle into the jack (it is a
loose fit) and turn it clockwise. As the jack touches the vehicle
and begins to lift, double-check that it is properly positioned.
CAUTION:
Never get under the vehicle when it is supported by the
jack alone.7. Remove the wheel nuts and remove the flat tire.
Lift the flat tire straight off and nut it aside.
Before putting on the spare wheel, remove any corrosion on
the mounting surfaces with a wire brush or such. Installation of
wheels without good metal-to-metal contact at the mounting
surface can cause wheel nuts to loosen and eventually cause
a wheel to come off while driving.

IN CASE OF AN EMERGENCY
139
8. Reinstall all the wheel nuts finger tight.
Align the holes in the wheel with the bolts. Then lift up the wheel
and get at least the top bolt started through its hole. Wiggle the
tire and press it back over the other bolts.
Reinstall the wheel nuts and tighten them as much as you can
by hand. Press the tire back and see if you can tighten them
more.
Tighten
Tightening torque:
103 N.m
(10.5 kgf-m,76 ft-lb.)
9. Lower the vehicle completely and tighten the wheel
nuts.
Turn the jack handle counterclockwise to lower the vehicle.
Use only the wheel nut wrench to tighten the nuts. Do not use
other tools or any additional leverage other than your hands,
such as a hammer, pipe or your foot. Make sure the wrench is
securely engaged over the nut.
Tighten each nut a little at a time in the order shown. Repeat
the process until all the nuts are tight.
CAUTION:
As soon as possible after changing wheels, have the
wheel nuts tightened by torque wrench at 103 N
.m (10.5
kgf.m, 76 ft.lb.).

IN CASE OF AN EMERGENCY
143
Emergency towing
Emergency towing eyeletsEmergency towing eyelets
If towing service is not available in an emergency, your
vehicle may be temporarily towed by a cable secured to
one of the eyelets under the front or rear of the vehicle.
A driver must be in the vehicle to steer it and operate the
brakes. Towing in this manner may be done only on
hard-surfaced roads for a short distance and at low speeds.
Also, the wheels, axles, drive train, steering and brakes must
all be in good condition.
Before towing, release the parking brake and put the
transmission in “N”. The ignition key must he in “ACC” (engine
off) or “ON” (engine running).CAUTION:
If the engine is not running, the power assist for the brakes
and steering will not work so steering and braking will be
much harder than usual.
IF YOU CANNOT SHIFT THE
AUTOMATIC TRANSMISSION
SELECTOR LEVER
Lock
Cover of shift lock
override button
If you cannot shift the selector lever out of “P” position to
other positions even though the brake pedal is depressed,
use the shift lock override button as follows:
1. Turn the ignition key to “LOCK”. Make sure the parking
brake is applied.
2. Pry up the cover with a flat-bladed screwdriver or
equivalent.

IN CASE OF AN EMERGENCY
144
3. Insert the screwdriver or equivalent into the hole to push
down the shift lock override button. You can shift out of “P”
position only while pushing the button.
4. Shift into “N” position.
5. Insert the cover.
6. Start the engine. For your safety, keep the brake pedal
depressed.
Be sure to have the system checked by your Lexus dealer as
soon as possible.
IF YOU LOSE YOUR KEYS OR
LOCK YOURSELF OUT
If you need replacement of an ignition key, contact your
Lexus dealer.
See the suggestion given in “Keys” on page 8.
If your keys are locked in the vehicle and you cannot get a
duplicate, many Lexus dealers can assist you. If you must
break a window to get in, we suggest breaking the smallest
side window because it is the least expensive to replace. Be
extremely cautious to avoid cuts from the glass.