drain LEXUS ES300 2005 User Guide
[x] Cancel search | Manufacturer: LEXUS, Model Year: 2005, Model line: ES300, Model: LEXUS ES300 2005Pages: 969, PDF Size: 24.08 MB
Page 273 of 969
3211X-04
F40995
F40996
BR3753
32-28
- BRAKEBRAKE BOOSTER ASSY
2462 Author: Date:
2005 LEXUS ES330 REPAIR MANUAL (RM1124U)
REPLACEMENT
1. REMOVE AIR CLEANER ASSY
2. DRAIN BRAKE FLUID
NOTICE:
Wash off the brake fluid immediately if it comes into contact with a painted surface.
3. REMOVE BRAKE MASTER CYLINDER SUB-ASSY (SEE PAGE 32-21)
SST 09023-00101
4. REMOVE VACUUM HOSE ASSY
(a) Remove the bolt and separate the vacuum hose from the
vacuum hose bracket.
(b) Slide the clip and disconnect the vacuum hose from the
brake booster.
5. REMOVE FRONT DOOR SCUFF PLATE LH (SEE PAGE 71-1 1)
6. REMOVE INSTRUMENT PANEL SUB-ASSY UPPER (SEE PAGE 71-1 1)
7. REMOVE INSTRUMENT PANEL INSERT SUB-ASSY LOWER LH (SEE PAGE 71-1 1)
8. REMOVE BRAKE PEDAL RETURN SPRING
9. REMOVE PUSH ROD PIN
(a) Remove the clip and push rod pin.
10. REMOVE BRAKE MASTER CYLINDER PUSH ROD CLEVIS
(a) Loosen the lock nut and remove the push rod clevis.
11. REMOVE FRONT BRAKE TUBE NO.5
(a) Using SST and remove the front brake tube No.5.
SST 09023-00101
12. REMOVE BRAKE BOOSTER ASSY
(a) Remove the 4 nuts.
(b) Pull out the brake booster assy.
Page 278 of 969
320E6-04
F41534
F41535
F41536
- BRAKEFRONT BRAKE
32-33
2467 Author: Date:
2005 LEXUS ES330 REPAIR MANUAL (RM1124U)
OVERHAUL
HINT:
Overhaul the RH side by the same procedures with LH side.
1. REMOVE FRONT WHEEL
2. DRAIN BRAKE FLUID
NOTICE:
Wash the brake fluid off immediately if it comes into contact with any painted surfaces.
3. DISCONNECT FRONT FLEXIBLE HOSE
(a) Remove the union bolt and a gasket from the disc brake cylinder, then disconnect the flexible hose
from the disc brake cylinder.
4. REMOVE DISC BRAKE CYLINDER ASSY LH
(a) Remove the 2 bolts and disc brake cylinder.
5. REMOVE DISC BRAKE PAD KIT FRONT (PAD ONLY)
(a) Remove the 2 brake pads with anti
squeal shims.
6. REMOVE ANTI SQUEAL SHIM KIT FRONT
(a) Remove the 2 anti squeal shims from 2 brake pads.
(b) Using a screwdriver, remove the wear indicator from 2
brake pads.
7. REMOVE FRONT DISC BRAKE PAD SUPPORT PLATE
(a) Remove the upper side front disc brake pad support plate.
8. REMOVE FRONT DISC BRAKE PAD SUPPORT PLATE
(a) Remove the bottom side front disc brake pad support plate.
9. REMOVE FRONT DISC BRAKE CYLINDER SLIDE PIN
(a) Remove the 2 cylinder slide pins from the disc brake cylin-
der mounting.
Page 286 of 969
320E8-04
F41547
F41548
F41550
- BRAKEREAR BRAKE
32-41
2475 Author: Date:
2005 LEXUS ES330 REPAIR MANUAL (RM1124U)
OVERHAUL
HINT:
Overhaul the RH side by the same procedures with LH side.
Two types of brake pad exist; one is with slit and the other without slit.
1. REMOVE REAR WHEEL
2. DRAIN BRAKE FLUID
NOTICE:
Wash the brake fluid off immediately if it comes into contact with any painted surfaces.
3. DISCONNECT REAR LH FLEXIBLE HOSE
(a) Remove the union bolt and a gasket from the disc brake cylinder, then disconnect the flexible hose
from the disc brake cylinder.
4. REMOVE REAR DISC BRAKE CYLINDER SLIDE PIN
(a) Remove the rear disc brake cylinder slide pin.
5. REMOVE DISC BRAKE CYLINDER ASSY REAR LH
(a) Lift up the disc brake cylinder and remove the disc brake
cylinder.
6. REMOVE REAR DISC BRAKE CYLINDER SLIDE
BUSH
(a) Remove the cylinder slide bush from the disc brake cylin-
der.
Page 293 of 969
320E2-04
F40998
C84798
To RL W/C
To FR W/C
To FL W/C
To RR W/C From M/C 2nd
From M/C 1st
F40998
32-48
- BRAKEBRAKE ACTUATOR ASSY (W/O VSC)
2482 Author: Date:
2005 LEXUS ES330 REPAIR MANUAL (RM1124U)
REPLACEMENT
1. DRAIN BRAKE FLUID
NOTICE:
Wash off the brake fluid immediately if it comes into contact with a painted surface.
2. REMOVE BRAKE ACTUATOR WITH BRACKET
(a) Using SST, disconnect the 6 brake lines from the actuator.
SST 09023-00101
(b) Use tags or make a memo to identify the place to recon-
nect.
(c) Disconnect the brake actuator connector.
(d) Remove the 3 nuts and brake actuator with bracket.
3. REMOVE BRAKE ACTUATOR ASSY
(a) Remove the 2 nuts and brake actuator from the bracket.
(b) Remove the 2 holders and 3 cushions from the brake actuator.
4. INSTALL BRAKE ACTUATOR ASSY
(a) Install the 3 cushions and 2 holders to the brake actuator.
(b) Install the brake actuator to the bracket with the 2 nuts.
Torque: 5.4 NVm (55 kgfVcm, 48 in.Vlbf)
5. INSTALL BRAKE ACTUATOR WITH BRACKET
(a) Install the brake actuator with the 3 nuts.
Torque: 19 NVm (194 kgfVcm, 14 ftVlbf)
(b) Connect the brake actuator connector.
Page 296 of 969
3211Y-04
F45680
F45681
From M/C 1st
To FL W/CFrom M/C 2nd
To RR W/C
To RL W/CTo FR W/C
F45682
- BRAKEBRAKE ACTUATOR ASSY (W/VSC)(From July, 2003)
32-51
2485 Author: Date:
2005 LEXUS ES330 REPAIR MANUAL (RM1124U)
REPLACEMENT
1. DRAIN BRAKE FLUID
NOTICE:
Wash off the brake fluid immediately if it comes into contact with a painted surface.
2. REMOVE BRAKE ACTUATOR WITH BRACKET
(a) Using SST, disconnect the 6 brake lines from the actuator.
SST 09023-00101
(b) Use tags or make a memo to identify the place to recon-
nect.
(c) Disconnect the actuator connector.
Page 353 of 969
300M5-01
C91611
SST
F40136
C83022
F40147
30-8
- DRIVE SHAFT / PROPELLER SHAFTFRONT DRIVE SHAFT (From July, 2003)
2411 Author: Date:
2005 LEXUS ES330 REPAIR MANUAL (RM1124U)
FRONT DRIVE SHAFT (From July, 2003)
OVERHAUL
HINT:
COMPONENTS: See page 30-4
Overhaul the RH side following the same procedures as for the LH side.
1. DRAIN AUTOMATIC TRANSAXLE FLUID
2. REMOVE FRONT WHEEL
3. REMOVE FRONT AXLE HUB LH NUT
(a) Using SST and a hammer, unstake the staked part of the
front axle hub LH nut.
SST 09930-00010
NOTICE:
Loosen the staked part of the lock nut completely, other-
wise the screw of the drive shaft may be damaged.
(b) While applying the brake, remove the front axle hub LH
nut.
4. DISCONNECT FRONT STABILIZER LINK ASSY LH
(a) Remove the nut, and separate the stabilizer link assy LH.
HINT:
If the ball joint turns together with the nut, use a hexagon
wrench (6 mm) to hold the stud.
5. DISCONNECT SPEED SENSOR FRONT LH
(a) Remove the bolt and clip, and separate the sensor wire
and hose from the shock absorber.
NOTICE:
Be careful not to damage the speed sensor.
(b) Remove the bolt, and separate the speed sensor front LH
from the steering knuckle.
NOTICE:
Prevent foreign matter from adhering to the speed sensor.
Page 383 of 969
141J7-02
A78541
(b)
(b)
(b)(a)
(a)
A36719
P18805
- ENGINE MECHANICALVALVE CLEARANCE (3MZ-FE)
14-7
2099 Author: Date:
2005 LEXUS ES330 REPAIR MANUAL (RM1124U)
VALVE CLEARANCE (3MZ-FE)
ADJUSTMENT
1. DISCONNECT BATTERY NEGATIVE TERMINAL
2. DRAIN ENGINE COOLANT (See page 16-9)
3. REMOVE FRONT FENDER APRON SEAL RH
4. REMOVE FRONT SUSPENSION UPPER BRACE CENTER (W/O TEMS) (See page 10-1 1)
5. REMOVE V-BANK COVER SUB-ASSY (See page 10-1 1)
6. REMOVE AIR CLEANER CAP SUB-ASSY (See page 10-1 1)
7. REMOVE EMISSION CONTROL VALVE SET (See page 11-13)
8. REMOVE INTAKE AIR SURGE TANK (See page 11-13)
9. REMOVE RADIATOR HOSE INLET
10. REMOVE IGNITION COIL ASSY
11. REMOVE CYLINDER HEAD COVER SUB-ASSY
(a) Remove the 2 engine wire harness clamps.
(b) Remove the 3 nuts, then disconnect the engine wire har-
ness.
(c) Remove the 9 bolts and cylinder head cover.
12. REMOVE CYLINDER HEAD COVER SUB-ASSY LH
(a) Using an E6 Torx) socket wrench, remove the 2 bolts and
disconnect the engine wire harness protector.
(b) Remove the 9 bolts and cylinder head cover.
13. INSPECT VALVE CLEARANCE
(a) Turn the crankshaft pulley, then align the timing notch with
the timing mark º0º of the timing belt No. 1 cover.
(b) Check that the valve lifters on the intake side of the No.
1 cylinder are not pushed by the cam.
If the valve lifters are pushed, turn the crankshaft by 1 revolution
(360) and align the marks as above.
Page 404 of 969
A78309
N´m (kgf´cm, ft´lbf)
: Specified torque
Non-reusable part O-ring
Gasket
8.0 (82, 71 in.Vlbf)
8.0 (82, 71 in.Vlbf)
45 (459, 33)
8.0 (82, 71 in.Vlbf)
8.0 (82, 71 in.Vlbf)
8.0 (82, 71 in.Vlbf)
8.0 (82, 71 in.Vlbf)
30 (306, 22)
43 (439, 32)
20 (199, 14)
8.0 (82, 71 in.Vlbf)
20 (199, 14)
8.0 (82, 71 in.Vlbf)
8.0 (82, 71 in.Vlbf)
20 (199, 14)
Oil Pan Sub-assy No. 2 Gasket Oil Strainer Sub-assy
Oil Pan Drain PlugOil Pan Sub-assy Oil Pump SealOil Pan Baffle Plate Oil Filter
Sub-assyx6 Water Inlet Housing
Engine Rear Oil Seal Retainer
Engine Rear
Oil Seal Cylinder Block Sub-assy
20 (199, 14)
Oil Pump Assy
14-28
- ENGINE MECHANICALPARTIAL ENGINE ASSY (3MZ-FE)
2120 Author: Date:
2005 LEXUS ES330 REPAIR MANUAL (RM1124U)
Page 405 of 969
141J9-02
A60072
- ENGINE MECHANICALPARTIAL ENGINE ASSY (3MZ-FE)
14-29
2121 Author: Date:
2005 LEXUS ES330 REPAIR MANUAL (RM1124U)
REPLACEMENT
1. DISCHARGE FUEL SYSTEM PRESSURE (See page 11-1)
2. DISCONNECT BATTERY NEGATIVE TERMINAL
3. REMOVE FRONT WHEELS
4. REMOVE ENGINE UNDER COVER NO.1
5. REMOVE ENGINE UNDER COVER NO.2
6. REMOVE FRONT FENDER APRON SEAL RH
7. DRAIN ENGINE COOLANT (See page 16-9)
8. DRAIN ENGINE OIL (See page 17-20)
9. DRAIN AUTOMATIC TRANSAXLE FLUID (See page 30-8)
10. REMOVE V-BANK COVER SUB-ASSY (See page 10-1 1)
11. REMOVE RADIATOR LOWER AIR DEFLECTOR (See page 19-5)
12. REMOVE BATTERY
13. REMOVE BATTERY TRAY
14. REMOVE AIR CLEANER INLET ASSY (See page 19-5)
15. REMOVE AIR CLEANER ASSY (See page 19-5)
16. REMOVE AIR CLEANER BRACKET (See page 19-5)
17. REMOVE AIR CLEANER INLET NO.1 (See page 19-5)
18. REMOVE INTAKE AIR RESONATOR SUB-ASSY
(a) Remove the clip and bolt, then remove the intake air resonator.
19. REMOVE V (COOLER COMPRESSOR TO CRANKSHAFT PULLEY) BELT NO.1
(See page 14-5)
20. REMOVE GENERATOR ASSY (See page 19-21)
21. REMOVE ENGINE MOVING CONTROL ROD (See page 14-79)
22. REMOVE ENGINE MOUNTING STAY NO.2 RH (See page 14-79)
23. REMOVE GENERATOR BRACKET NO.2 (See page 14-79)
24. REMOVE GENERATOR BELT ADJUSTING BAR (See page 17-9)
25. SEPARATE COMPRESSOR AND MAGNETIC CLUTCH (See page 17-9)
26. SEPARATE TRANSMISSION CONTROL CABLE ASSY (See page 40-44)
27. DISCONNECT UNION TO CHECK VALVE HOSE
28. DISCONNECT FUEL VAPOR FEED HOSE NO.1
29. DISCONNECT FUEL PIPE SUB-ASSY NO.1 (See page 11-1)
30. DISCONNECT HEATER INLET WATER HOSE
31. DISCONNECT HEATER OUTLET WATER HOSE
32. DISCONNECT RADIATOR HOSE INLET
33. DISCONNECT RADIATOR HOSE OUTLET
34. DISCONNECT OIL COOLER INLET HOSE
35. DISCONNECT OIL COOLER OUTLET HOSE
36. DISCONNECT OIL RESERVOIR TO PUMP HOSE NO.1
Page 425 of 969
A78720
SST
A36750
A00019
SST
SST
B04136
- ENGINE MECHANICALPARTIAL ENGINE ASSY (3MZ-FE)
14-49
2141 Author: Date:
2005 LEXUS ES330 REPAIR MANUAL (RM1124U)
42. REMOVE OIL FILTER SUB-ASSY
(a) Using SST, remove the oil filter.
SST 09228-07501
(b) Using a socket hexagon wrench 12, remove the oil filter
union.
43. REMOVE OIL PAN DRAIN PLUG
44. REMOVE OIL PAN SUB-ASSY NO.2
(a) Remove the 10 bolts and 2 nuts.
(b) Insert the blade of SST between the oil pan No. 1 and oil
pan No. 2, then cut off the sealer and remove the oil pan
No. 2.
SST 09032-00100
NOTICE:
Be careful not to damage the contact surface of the oil
pan No. 1 where the oil pan No. 2 is mounted.
Do not damage the flange portion of the oil pan No. 2
when removing.
45. REMOVE OIL STRAINER SUB-ASSY
(a) Remove the bolt and 2 nuts, then remove the oil strainer and gasket.
46. REMOVE OIL PAN SUB-ASSY
(a) Loosen and remove the 15 bolts and 2 nuts uniformly.