drain LEXUS ES300 2005 Workshop Manual

1809E-02
A86234
(a)(b)
(b)
(b)(a)
(a)
RH Bank:
A86235
(a)
(b)(b)
(b)
(a)
(a)LH Bank:
- IGNITIONIGNITION COIL ASSY (3MZ-FE)
18-7
2332 Author
: Date
:
2005 LEXUS ES330 REPAIR MANUAL (RM1124U)
IGNITION COIL ASSY (3MZ-FE)
REPLACEMENT
1. DISCONNECT ENGINE WIRE NO. 3 (BATTERY NEGATIVE TERMINAL)
2. DRAIN ENGINE COOLANT (RH BANK) (See page 10-1 1)
3. REMOVE FRONT SUSPENSION UPPER BRACE CENTER (W/O TEMS, RH BANK)
(See page 16-9)
4. REMOVE V-BANK COVER SUB-ASSY (See page 16-9)
5. REMOVE AIR CLEANER CAP SUB-ASSY (RH BANK) (See page 16-9)
6. REMOVE EMISSION CONTROL VALVE SET (RH BANK) (See page 11-13)
7. REMOVE INTAKE AIR SURGE TANK (RH BANK) (See page 11-13)
8. REMOVE IGNITION COIL ASSY
(a) Disconnect the 6 connectors.
(b) Remove the 6 bolts, then remove the 6 ignition coils.
HINT:
The ignition coil is installed with the bolt.
9. INSTALL IGNITION COIL ASSY
Torque: 8.0 NVm (80 kgfVcm, 71 in.Vlbf)
10. INSTALL INTAKE AIR SURGE TANK (RH BANK) (See page 11-13)
11. INSTALL EMISSION CONTROL VALVE SET (RH BANK) (See page 11-13)
12. INSTALL AIR CLEANER CAP SUB-ASSY (RH BANK) (See page 16-9)
13. CHECK CONNECTION OF VACUUM HOSE (RH BANK) (See page 14-29)
14. CONNECT ENGINE WIRE NO. 3 (BATTERY NEGATIVE TERMINAL)
Torque: 5.4 NVm (55 kgfVcm, 48 in.Vlbf)
15. ADD ENGINE COOLANT (RH BANK) (See page 10-1 1)
16. CHECK FOR ENGINE COOLANT LEAKS (RH BANK) (See page 16-1)
17. INSTALL V-BANK COVER SUB-ASSY (See page 16-9)
18. INSTALL FRONT SUSPENSION UPPER BRACE CENTER (W/O TEMS, RH BANK)
(See page 16-9)
19. SYSTEM INITIALIZATION (See page 19-15)

51069-02
F41598
F41599
- POWER STEERINGVANE PUMP ASSY
51-9
2584 Author
: Date
:
2005 LEXUS ES330 REPAIR MANUAL (RM1124U)
OVERHAUL
NOTICE:

When using a vise, do not over tighten.

When installing, coat the parts indicated by the arrows with power steering fluid
(See page 51-7).
1. REMOVE FRONT WHEEL RH
2. DRAIN POWER STEERING FLUID
3. REMOVE FRONT FENDER LINER RH
4. REMOVE FRONT FENDER APRON SEAL RH
5. DISCONNECT OIL RESERVOIR TO PUMP HOSE NO.1
(a) Remove the clip and disconnect the oil reservoir to pump hose No.1.
NOTICE:
Take care not to spill fluid on the V belt.
6. REMOVE POWER STEERING OIL PRESSURE SWITCH
(a) Disconnect the connector.
(b) Remove the oil power steering pressure switch from the union bolt.
NOTICE:
Be careful not to drop the oil power steering pressure switch.
If the oil power steering pressure switch is dropped or strongly damaged, replace it with a new one.
7. DISCONNECT PRESSURE FEED HOSE
(a) Using a spanner (22 mm) to hold the pressure port union,
remove the union bolt and gasket.
8. REMOVE VANE PUMP V BELT
(a) Loosen the 2 bolts and remove the vane pump V belt.
9. REMOVE VANE PUMP ASSY
(a) Remove the 2 bolts and vane pump assy.

Lexus Supports ASE CertificationPage 1 of 4
Title:
BATTERY MAINTENANCE FOR
IN-STOCK VEHICLES & PRE-DELIVERY
Models:
All Models & Model Years Through Current
Technical Service
Information Bulletin
September 12, 2002
PG009-02
A battery in a stored vehicle is subject to conditions that can reduce its performance and
life. These conditions include storage period, temperature, parasitic drain, and battery
load. Because of these factors, battery inspection and maintenance are required in
order to ensure proper operation and optimal battery life.
As a matter of policy, Lexus does not provide battery warranty coverage for discharged
and/or failed batteries due to lack of maintenance; it is the dealer's responsibility to
maintain the specified state of charge of the vehicle's battery while in stock and assure
proper state of charge at delivery.
To eliminate customer service concerns due to an undercharged battery during the first
few weeks of ownership, all dealers should check battery state of charge and
recharge, if necessary, just prior to delivery (i.e., within 48 hours of delivery).
This new procedure will improve the new vehicle ownership experience by greatly
reducing the risk of having a low performance battery concern due to extended storage
periods and/or short engine run times prior to the vehicle sale.
All models and model years through current.
SPECIAL SERVICE TOOLS (SSTs)MANUFACTURERPART NUMBER
MICROPRO 815 Digital
Battery Analyzer
(Essential SST)*Midtronics00002±MP815±T
* This SST can be ordered through SPX/OTC by calling 1±800±933±8335.
NOTE:
MICROPRO 815 Digital Battery Analyzer should be periodically updated through the
Technical Information System (TIS) for new vehicle models. For detailed information,
please see TSIB SS002±02, ªMidtronics Battery Tester Software Update.º
OP CODEDESCRIPTIONTIMEOFPT1T2
N/ANot Applicable to Warranty±±±±
PRODUCT GENERAL INFORMATION
Introduction
Applicable
Vehicles
Required
Tools &
Material
Warranty
Information

BATTERY MAINTENANCE FOR IN±STOCK VEHICLES & PRE±DELIVERY ± PG009-02 September 12, 2002
Page 4 of 4
In addition to this new pre±delivery battery test, a monthly battery inspection is still
required for stored vehicles. If your dealership is located in an area subject to extreme
temperatures (hot or cold), periodic maintenance may need to be performed more
frequently.
To reduce parasitic battery drain for vehicles in storage for one week or more, the
negative battery cable should always be disconnected to reduce battery discharge.
When the negative battery cable is reconnected, please check and reset electrical
components such as the clock, radio, etc.
NOTE:
For your reference, the electrical system is made inoperative by removing the
appropriate fuse indicated in the Electrical Wiring Diagram. Recom-
mended
Battery
Maintenance