reset LEXUS ES300 2005 Owner's Manual

DIAGNOSTIC TESTER IMMOBILIZER FUNCTIONS ± SS005-01 Revised July 6, 2001
Page 13 of 14
D. Verify that keys are registered correctly by starting the engine with each newly
registered key.
NOTE:
If the vehicle starts, the new key code was registered correctly.
If the vehicle does not start with any key, perform the Immobilizer Reset function
again.
If only one of the registered keys will not start the vehicle, attempt to register the
key again following the Transponder Code Registration procedure (page 5 of
this bulletin).
5. Transponder ECU Replacement
When the Transponder ECU is replaced, the transponder keys must be registered,
auto registration closed, and ECU communication completed.
A. Replacement transponder ECUs are in auto registration mode. This allows
transponder keys to automatically register as they are inserted into the ignition
cylinder. It is possible to automatically register 3 Master Keys, and 1 Sub Key.
NOTE:
If 4 keys are registered at this time, auto registration mode is closed.
If less than 4 keys are registered at this time, auto registration mode must be closed
manually by cycling the ignition ON/OFF more than 5 times in 10 seconds.
If more than 4 keys need to be registered, use Transponder Code Registration
procedure (page 5 of this bulletin).
B. Once auto registration mode is closed, ECU Communication must be performed
between the transponder ECU and the Engine ECU. Complete ECU
communication using the following steps:
a. Insert registered Master Key into the ignition cylinder.
b. Turn ignition ON (engine OFF).
c. Short Tc and CG terminals of DLC3 using Diagnosis Check Wire
(SST 09843±18040 or equivalent) and leave for 30 minutes. (See Figure 10.)
16 15 14 13 12 11 10 9
87 654321
View of Connector Is From Passenger Compartment
FIGURE 10. DLC3
Tc = Pin 13
CG = Pin 4SST 09843±18040
d. After 30 minutes, turn ignition OFF and remove check wire from DLC3
e. Start the vehicle to confirm successful ECU communication.
NOTE:
If ECU communication is not completed correctly, the engine will not start and DTC
B2799 will be set. DTC B2799 will be cleared after engine starts correctly. Operation
Procedure
(Continued)
TRANSPONDER
ECU RESET
TRANSPONDER
ECU
REPLACEMENT

Lexus Supports ASE CertificationPage 1 of 3
Title:
ECM RESET MEMORY FUNCTION
Models:
'98 ± '05 Applicable Models
Technical Service
Information Bulletin
May 5, 2003
TC002-03
TSIB REVISION NOTICE:
December 20, 2004: Applicable Vehicles section has been updated and modified,
2004 and 2005 model years added; and Reset Procedure 2 has been revised.
Previous versions of this TSIB should be discarded.
Whenever an automatic transmission is replaced, overhauled or individual components
are replaced, use this procedure to erase Engine Control Module (ECM, SAE term:
Powertrain Control Module, PCM) ªLearned Valuesº and minimize subsequent
performance concerns.
CAUTION:
Failure to follow the following procedure may lengthen the time to readjust the
ªLearned Values,º potentially resulting in performance concerns.
Refer to Reset Procedure 1 for the following vehicles with Electronically Controlled
Automatic Transmissions:
1999 ± 2003 model year ES 300 and RX 300 vehicles.
2003 ± 2005 model year GX 470 vehicles.
2004 ± 2005 model year RX 330 vehicles.
Refer to Reset Procedure 2 for the following vehicles with Electronically Controlled
Automatic Transmissions:
1998 ± 2005 model year GS 430/400/300, LS 430/400, LX 470, and
SC 430/400/300 vehicles.
2001 ± 2005 model year IS 300 vehicles.
OP CODEDESCRIPTIONTIMEOFPT1T2
N/ANot Applicable to Warranty±±±±
TRANSMISSION & CLUTCH
Introduction
Applicable
Vehicles
Warranty
Information

RESET MEMORY FUNCTION ± TC002-03 Revised May 5, 2003
Page 2 of 3
SPECIAL SERVICE TOOLS (SSTs)PART NUMBERQUANTITY
Lexus Diagnostic Tester Kit*010012701
CAN Interface Module Kit*010027441
12 Megabyte Diagnostic Tester Program Card
with version 12.01a Software (or later)*01002593-0051
* Essential SSTs.
NOTE:
Additional Diagnostic Tester Kits, CAN Interface Modules, Program Cards or other
SSTs may be ordered by calling SPX/OTC at 1-800-933-8335.
1. Connect the Lexus Diagnostic Tester to the vehicle.
2. Reset the ECM (PCM). Refer to the procedures below.
DO YOU WISH TO
RESET THE ECM?
[YES] to CONTINUE
[NO] to EXIT
2: CUSTOMIZE
3: ECU REPROGRAMFUNCTION SELECT FOR
NORTH AMERICA
B
*APPLICATION SELECT*
A
1: DIAGNOSISDIAGNOSTIC MENU
ENGINE
C
DO NOT USE THIS
FUNCTION UNLESS
INSTRUCTED BY
REPAIR MANUAL.RESET MEMORY
E
RESET MEMORY
NOTICE
D
[YES]
F
1: OBD/MOBD
3: CARB OBD II
4: BREAK±OUT BOX
5: NVH
6: AUTOPROBE
7: 02 RPM CHECK
8: SNAPSHOT REVIEW
9: SETUP
0: GAS ANALYSIS2: ENHANCED OBD II1: DATA LIST
2: DTC INFO
3: ACTIVE TEST
4: SNAPSHOT
5: SYSTEM CHECK
6: RESET MEMORY
7: MONITOR STATUS
8: CHECK MODE
6: RESET MEMORY
ONLY USE AFTER
REPLACING THE ENGINE,
AUTO TRANS, OR ECM
ON CERTAIN VEHICLES.EXECUTING THIS
FUNCTION WILL RESET
THE LEARNED VALUES
IN THE ECM.RESET MEMORY
RESETTING COMPLETE
PRESS
[ENTER]
3. Start the engine and warm it up to normal operating temperatures before test±driving.
4. Perform a thorough test drive with several accelerations from a stop with ªlight
throttleº application until proper transmission shifting is verified.
Required
SSTs
Reset
Procedure 1

RESET MEMORY FUNCTION ± TC002-03 Revised May 5, 2003
Page 3 of 3
1. Disconnect the negative battery cable for 5 minutes.
2. Reconnect battery cable.
3. Start the engine and warm it up to normal operating temperatures before test±driving.
4. Perform a thorough test drive with several accelerations from a stop with ªlight
throttleº application until proper transmission shifting is verified.Reset
Procedure 2

ECM CALIBRATION: SHIFTING ENHANCEMENT ± TC004-03 Revised August 4, 2003
Page 6 of 6
5.Reset the ECM (PCM) learned values using the diagnostic tester. Refer to the
procedures below.
± The sample screen prints seen below are the 12.01a software version and may
differ from subsequent software versions.
NOTE:
Failure to reset the ECM (PCM) memory will result in continued ATM shifting complaints.
DO YOU WISH TO
RESET THE ECM?
[YES] to CONTINUE
[NO] to EXIT
2: CUSTOMIZE
3: ECU REPROGRAMFUNCTION SELECT FOR
NORTH AMERICA
B
*APPLICATION SELECT*
A
1: DIAGNOSISDIAGNOSTIC MENU
ENGINE
C
DO NOT USE THIS
FUNCTION UNLESS
INSTRUCTED BY
REPAIR MANUAL.RESET MEMORY
E
RESET MEMORY
NOTICE
D
[YES]
F
1: OBD/MOBD
3: CARB OBD II
4: BREAK±OUT BOX
5: NVH
6: AUTOPROBE
7: 02 RPM CHECK
8: SNAPSHOT REVIEW
9: SETUP
0: GAS ANALYSIS2: ENHANCED OBD II1: DATA LIST
2: DTC INFO
3: ACTIVE TEST
4: SNAPSHOT
5: SYSTEM CHECK
6: RESET MEMORY
7: MONITOR STATUS
8: CHECK MODE
6: RESET MEMORY
ONLY USE AFTER
REPLACING THE ENGINE,
AUTO TRANS, OR ECM
ON CERTAIN VEHICLES.EXECUTING THIS
FUNCTION WILL RESET
THE LEARNED VALUES
IN THE ECM.RESET MEMORY
RESETTING COMPLETE
PRESS
[ENTER]
Figure 3. ECM (PCM) Learned Values Reset
6. Follow the procedures outlined in TSIB No. EG012±04, ªEntering VIN During ECM
(PCM) Replacement and/or DTC P0630,º
and write the VIN to the ECM (PCM).
7. Start the engine and warm it up to normal operating temperature before test±driving.
8. Test drive vehicle to confirm proper vehicle operation.
9. Enter the required information on the Authorized Modifications Label and affix it to the
vehicle at the location shown in Figure 1 (page 4). The Authorized Modifications
Label is available through the MDC, P/N 00451±00001±LBL.
10. Calibration update is complete.
NOTE:
Select premium unleaded gasoline with an Octane Rating of 91 (Research Octane
Number 96) or higher for optimum engine performance.
The effect of the new calibration may become more apparent after several days
of driving as the ECM (PCM) ºlearned valuesº are re±established from the
customer 's driving. Repair
Procedure
(Continued)