check engine LEXUS ES300 2005 Service Manual

A86260
Non-reusable part
: Specified torque VSV Connector
8.0 (82, 71 in.Vlbf)x2
Emission
Control Valve Set
Emission Control Valve Bracket
Intake Air Surge Tank

Air Surge Tank
to Intake Manifold
Gasket
Throttle Motor Connector
Water By-pass Hose No. 3
Water By-pass Hose No. 2
N´m (kgf´cm, ft´lbf)
Union to Check Valve Hose
Fuel Vapor Feed Hose
x2 x3
Engine Hunger No. 1Surge Tank Stay
No. 1
Surge Tank Stay
No. 2
20 (199, 14)
20 (199, 14)
20 (199, 14)
7.8 (80, 69 in.Vlbf)
x2
x2 Pressure Feed
Tube Assy
28 (286, 21)
x2
x2
Bond Cable No. 1
Connector
28 (286, 21)
14-88
- ENGINE MECHANICALCAMSHAFT (RH BANK) (3MZ-FE)
2180 Author
: Date
:
2005 LEXUS ES330 REPAIR MANUAL (RM1124U)

A78739
Align
A05204
A78740
101
23
4
5
6
7
8
9
- ENGINE MECHANICALCAMSHAFT (RH BANK) (3MZ-FE)
14-99
2191 Author
: Date
:
2005 LEXUS ES330 REPAIR MANUAL (RM1124U)
33. INSTALL CAMSHAFT
NOTICE:
Since the thrust clearance of the camshaft is small, the
camshaft must be kept level while being installed. If the
camshaft is not kept level, the cylinder head or camshaft
may be damaged. To avoid this, the following steps must
be carried out.
(a) Apply new engine oil to the thrust portion and journal of
the camshaft.
(b) Align the timing marks (2 dot marks) of the camshaft drive
and driven gears.
(c) Place the camshaft on the cylinder head.
(d) Install the 5 bearing caps in their proper locations.
(e) Apply a light coat of engine oil to the threads of the bear-
ing cap bolts.
(f) Using several steps, tighten the 10 bearing cap bolts uni-
formly in the sequence shown in the illustration.
Torque: 16 NVm (163 kgfVcm, 12 ftVlbf)
(g) Remove the service bolt.
34. INSTALL TIMING BELT NO.3 COVER
(a) Visually check for cracks and breaks on the gasket of the
timing belt cover.
HINT:
If there is a trace of water intrusion when checking visually, re-
pair the gasket with seal packing when the crack length is within
2 to 3 cm (0.79 to 1.18 in.). Replace the gasket when the crack
length is 3 to 4 cm (1.18 to 1.57 in.) or longer.

14-102
- ENGINE MECHANICALCAMSHAFT (RH BANK) (3MZ-FE)
2194 Author
: Date
:
2005 LEXUS ES330 REPAIR MANUAL (RM1124U)
55. INSTALL INTAKE AIR SURGE TANK (See page 11-13)
56. INSTALL EMISSION CONTROL VALVE SET (See page 11-13)
57. INSTALL AIR CLEANER CAP SUB-ASSY (See page 10-1 1)
58. CHECK CONNECTION OF VACUUM HOSE (See page 14-29)
59. INSTALL V-BANK COVER SUB-ASSY (See page 10-1 1)
60. INSTALL FRONT SUSPENSION UPPER BRACE CENTER (W/O TEMS) (See page 10-1 1)
61. INSTALL FRONT WHEEL RH (See page 14-5)
62. ADD ENGINE COOLANT (See page 16-9)
63. CHECK FOR ENGINE COOLANT LEAKS (See page 16-1)
64. SYSTEM INITIALIZATION (See page 19-15)

- ENGINE MECHANICALCAMSHAFT (LH BANK) (3MZ-FE)
14-1 11
2203 Author
: Date
:
2005 LEXUS ES330 REPAIR MANUAL (RM1124U)
34. INSPECT TIMING BELT (See page 14-79)
35. INSTALL TIMING BELT (See page 14-79)
SST 09960-10010 (09962-01000, 09963-01000)
36. INSTALL TIMING BELT TENSIONER ASSY (See page 14-79)
37. INSTALL TIMING BELT GUIDE NO.2 (See page 14-79)
38. INSTALL ENGINE MOUNTING BRACKET RH (See page 14-79)
39. INSTALL TIMING BELT NO.2 COVER (See page 14-79)
40. INSTALL TIMING BELT NO.1 COVER (See page 14-79)
41. INSTALL CRANKSHAFT PULLEY (See page 14-79)
SST 09213-54015 (91651-60855), 09330-00021
42. INSTALL GENERATOR BRACKET NO.2 (See page 14-79)
43. INSTALL ENGINE MOUNTING STAY NO.2 RH (See page 14-79)
44. INSTALL ENGINE MOVING CONTROL ROD (See page 14-79)
45. INSPECT VALVE CLEARANCE (See page 14-7)
46. ADJUST VALVE CLEARANCE (See page 14-7)
SST 09248-55040 (09248-05410, 09248-05420)
47. INSTALL VANE PUMP V BELT (See page 14-5)
48. INSTALL V (COOLER COMPRESSOR TO CRANKSHAFT PULLEY) BELT NO.1
(See page 14-5)
49. INSPECT DRIVE BELT DEFLECTION AND TENSION (See page 14-1)
50. INSTALL CYLINDER HEAD COVER SUB-ASSY LH (See page 14-7)
51. INSTALL IGNITION COIL ASSY (See page 14-7)
52. INSTALL V-BANK COVER SUB-ASSY (See page 10-1 1)
53. INSTALL FRONT WHEEL RH (See page 14-5)
54. ADD ENGINE COOLANT (See page 16-9)
55. CHECK FOR ENGINE COOLANT LEAKS (See page 16-1)
56. SYSTEM INITIALIZATION (See page 19-15)

A86260 Non-reusable part
: Specified torque VSV Connector
8.0 (82, 71 in.Vlbf)x2
Emission
Control Valve Set
Emission Control Valve Bracket
Intake Air Surge Tank
 Air Surge Tank
to Intake Manifold
Gasket
Throttle Motor Connector
Water By-pass Hose No. 3
Water By-pass Hose No. 2
N´m (kgf´cm, ft´lbf)
Union to Check Valve Hose
Fuel Vapor Feed Hose
x2 x3
Engine Hunger No. 1Surge Tank Stay
No. 1
Surge Tank Stay
No. 2
20 (199, 14)
20 (199, 14)
20 (199, 14)
7.8 (80, 69 in.Vlbf)
x2
x2 Pressure Feed
Tube Assy
28 (286, 21)
x2
x2
Bond Cable No. 1
Connector
28 (286, 21)
- ENGINE MECHANICALCYLINDER HEAD GASKET (3MZ-FE)
14-1 13
2205 Author
: Date
:
2005 LEXUS ES330 REPAIR MANUAL (RM1124U)

A78721
Tension Portion
A78324
Front
A78717
1
2
3
4
5
67
8
Front
A78730
90
Front
Painted Mark 14-122
- ENGINE MECHANICALCYLINDER HEAD GASKET (3MZ-FE)
2214 Author
: Date
:
2005 LEXUS ES330 REPAIR MANUAL (RM1124U)
40. INSPECT CYLINDER HEAD SET BOLT
(a) Using vernier calipers, measure the tension portion diam-
eter of the bolt.
Standard outside diameter:
8.95 to 9.05 mm (0.3524 to 0.3563 in.)
Minimum outside diameter: 8.75 mm (0.3445 in.)
If the diameter is less than minimum, replace the bolt.
41. INSTALL CYLINDER HEAD GASKET
(a) Place a new cylinder head gasket on the cylinder block
with the R mark upward.
NOTICE:

Remove any oil from the contact surface.

Be careful of the installing orientation.

Place the cylinder head on the gasket carefully in or-
der not to damage the gasket at the bottom part of the
head.
42. INSTALL CYLINDER HEAD SUB-ASSY
NOTICE:
The cylinder head bolts are tightened in 2 successive
steps.
(a) Apply a light coat of engine oil to the threads of the cylin-
der head bolts.
(b) Install the plate washers to the cylinder head bolts.
(c) Using several steps, install and tighten the 8 cylinder
head bolts uniformly in the sequence shown in the illustra-
tion.
Torque: 54 NVm (550 kgfVcm, 40 ftVlbf)
(d) Mark the front side of each cylinder head bolt head with
paint as shown in the illustration.
(e) Retighten the cylinder head bolts by 90in the same se-
quence as step (c).
(f) Check that each painted mark is now at a 90 angle to the
front.

14-124
- ENGINE MECHANICALCYLINDER HEAD GASKET (3MZ-FE)
2216 Author
: Date
:
2005 LEXUS ES330 REPAIR MANUAL (RM1124U)
68. INSTALL V (COOLER COMPRESSOR TO CRANKSHAFT PULLEY) BELT NO.1
(See page 14-5)
69. INSPECT DRIVE BELT DEFLECTION AND TENSION (See page 14-1)
70. INSTALL WATER OUTLET (See page 10-16)
71. INSTALL INTAKE MANIFOLD (See page 10-16)
72. INSTALL INTAKE AIR SURGE TANK (See page 11-13)
73. INSTALL EMISSION CONTROL VALVE SET (See page 11-13)
74. INSTALL AIR CLEANER CAP SUB-ASSY (See page 10-1 1)
75. CHECK CONNECTION OF VACUUM HOSE (See page 14-29)
76. INSTALL V-BANK COVER SUB-ASSY (See page 10-1 1)
77. INSTALL FRONT SUSPENSION UPPER BRACE CENTER (W/O TEMS) (See page 10-1 1)
78. INSTALL FRONT WHEEL RH (See page 14-5)
79. ADD ENGINE OIL (See page 17-20)
80. ADD ENGINE COOLANT (See page 16-9)
81. CHECK FOR ENGINE OIL LEAKS
82. CHECK FOR ENGINE COOLANT LEAKS (See page 16-1)
83. INSPECT FOR FUEL LEAKS
84. CHECK FOR EXHAUST GAS LEAKS
85. INSPECT IGNITION TIMING (See page 14-1)
SST 09843-18040
86. INSPECT ENGINE IDLE SPEED (See page 14-1)
87. INSPECT COMPRESSION (See page 14-1)
SST 09992-00500
88. INSPECT CO/HC (See page 14-1)
89. SYSTEM INITIALIZATION (See page 19-15)

A86260 Non-reusable part
: Specified torque VSV Connector
8.0 (82, 71 in.Vlbf)x2
Emission
Control Valve Set
Emission Control Valve Bracket
Intake Air Surge Tank
 Air Surge Tank
to Intake Manifold
Gasket
Throttle Motor Connector
Water By-pass Hose No. 3
Water By-pass Hose No. 2
N´m (kgf´cm, ft´lbf)
Union to Check Valve Hose
Fuel Vapor Feed Hose
x2 x3
Engine Hunger No. 1Surge Tank Stay
No. 1
Surge Tank Stay
No. 2
20 (199, 14)
20 (199, 14)
20 (199, 14)
7.8 (80, 69 in.Vlbf)
x2
x2 Pressure Feed
Tube Assy
28 (286, 21)
x2
x2
Bond Cable No. 1
Connector
28 (286, 21)
14-126
- ENGINE MECHANICALCYLINDER HEAD GASKET NO.2 (3MZ-FE)
2218 Author
: Date
:
2005 LEXUS ES330 REPAIR MANUAL (RM1124U)

A78719
1
2
3
4
5
67
8
Front
A78730
90
Front
Painted Mark
A78718
Front
- ENGINE MECHANICALCYLINDER HEAD GASKET NO.2 (3MZ-FE)
14-135
2227 Author
: Date
:
2005 LEXUS ES330 REPAIR MANUAL (RM1124U)
43. INSTALL CYLINDER HEAD LH
NOTICE:
The cylinder head bolts are tightened in 2 successive
steps.
(a) Apply a light coat of engine oil to the threads of the cylin-
der head bolts.
(b) Install the plate washer to the cylinder head bolt.
(c) Using several steps, install and tighten the 8 cylinder
head bolts uniformly in the sequence shown in the illustra-
tion.
Torque: 54 NVm (550 kgfVcm, 40 ftVlbf)
(d) Mark the front side of each cylinder head bolt head with
paint as shown in the illustration.
(e) Retighten the cylinder head bolts by 90in the same se-
quence as step (c).
(f) Check that each painted mark is now at a 90 angle to the
front.
(g) Using a socket hexagon wrench 8, install the hexagon
bolt.
Torque: 19 NVm (189 kgfVcm, 14 ftVlbf)
(h) Install the wire harness clamp bracket with the bolt.
Torque: 5.4 NVm (55 kgfVcm, 48 in.Vlbf)
(i) Connect the ground cable with the bolt.
Torque: 5.4 NVm (55 kgfVcm, 48 in.Vlbf)
44. INSTALL NO.4 CAMSHAFT SUB-ASSY (See page 14-107)
45. INSTALL NO.3 CAMSHAFT SUB-ASSY (See page 14-107)
46. INSTALL CYLINDER HEAD COVER SUB-ASSY LH (See page 14-7)
47. INSTALL IGNITION COIL ASSY (See page 14-7)
48. INSTALL WATER INLET PIPE (See page 16-16)

A86573
O-ring
14-136
- ENGINE MECHANICALCYLINDER HEAD GASKET NO.2 (3MZ-FE)
2228 Author
: Date
:
2005 LEXUS ES330 REPAIR MANUAL (RM1124U)
49. INSTALL OIL LEVEL GAGE GUIDE
(a) Install a new O-ring to the oil level gage guide.
(b) Apply soapy water to the O-ring.
(c) Push in the oil level gage guide end into the guide hole of
the cylinder block.
(d) Install the oil level gage guide with the bolt.
Torque: 8.0 NVm (82 kgfVcm, 71 in.Vlbf)
(e) Install the oil level gage.
50. INSTALL EXHAUST PIPE ASSY FRONT (See page 15-2)
51. INSTALL MANIFOLD STAY NO.2 (See page 14-29)
52. INSTALL TIMING BELT NO.3 COVER (See page 14-93)
53. INSTALL CAMSHAFT TIMING PULLEY (See page 14-93)
SST 09960-10010 (09962-01000, 09963-01000), 09249-63010
54. INSTALL TIMING BELT IDLER SUB-ASSY NO.2 (See page 14-93)
55. INSPECT TIMING BELT (See page 14-79)
56. INSTALL TIMING BELT (See page 14-79)
SST 09960-10010 (09962-01000, 09963-01000)
57. INSTALL TIMING BELT TENSIONER ASSY (See page 14-79)
58. INSTALL TIMING BELT GUIDE NO.2 (See page 14-79)
59. INSTALL ENGINE MOUNTING BRACKET RH (See page 14-79)
60. INSTALL TIMING BELT NO.2 COVER (See page 14-79)
61. INSTALL TIMING BELT NO.1 COVER (See page 14-79)
62. INSTALL CRANKSHAFT PULLEY (See page 14-79)
SST 09213-54015 (91651-60855), 09330-00021
63. INSTALL GENERATOR BRACKET NO.2 (See page 14-79)
64. INSTALL ENGINE MOUNTING STAY NO.2 RH (See page 14-79)
65. INSTALL ENGINE MOVING CONTROL ROD (See page 14-79)
66. INSTALL VANE PUMP V BELT (See page 14-5)
67. INSTALL V (COOLER COMPRESSOR TO CRANKSHAFT PULLEY) BELT NO.1
(See page 14-5)
68. INSPECT DRIVE BELT DEFLECTION AND TENSION (See page 14-1)
69. INSTALL WATER OUTLET (See page 10-16)
70. INSTALL INTAKE MANIFOLD (See page 10-16)
71. INSTALL INTAKE AIR SURGE TANK (See page 11-13)
72. INSTALL EMISSION CONTROL VALVE SET (See page 11-13)
73. INSTALL AIR CLEANER CASE (See page 19-5)
74. INSTALL AIR CLEANER CAP SUB-ASSY (See page 10-1 1)
75. INSTALL AIR CLEANER INLET ASSY (See page 19-5)
76. CHECK CONNECTION OF VACUUM HOSE (See page 14-29)
77. INSTALL V-BANK COVER SUB-ASSY (See page 10-1 1)
78. INSTALL FRONT SUSPENSION UPPER BRACE CENTER (W/O TEMS) (See page 10-1 1)
79. INSTALL FRONT WHEEL RH (See page 14-5)
80. ADD ENGINE OIL (See page 17-20)
81. ADD ENGINE COOLANT (See page 16-9)
82. CHECK FOR ENGINE OIL LEAKS
83. CHECK FOR ENGINE COOLANT LEAKS (See page 16-1)
84. INSPECT FOR FUEL LEAKS