check engine LEXUS ES300 2005 Manual PDF
[x] Cancel search | Manufacturer: LEXUS, Model Year: 2005, Model line: ES300, Model: LEXUS ES300 2005Pages: 969, PDF Size: 24.08 MB
Page 543 of 969
P12406
A37157
ZF6928
A78806
No. 1 and No. 4:
Upper
Lower
22.4 mm (0.882 in.)No. 2 and No. 3:
19.0 mm (0.748 in.)
- ENGINE MECHANICALCYLINDER BLOCK ASSY (3MZ-FE)
14-167
2259 Author: Date:
2005 LEXUS ES330 REPAIR MANUAL (RM1124U)
29. INSPECT CRANKSHAFT
(a) Using a dial indicator and V-blocks, measure the circle
runout as shown in the illustration.
Maximum circle runout: 0.06 mm (0.0024 in.)
If the circle runout is greater than maximum, replace the crank-
shaft.
(b) Using a micrometer, measure the diameter of each main
journal.
Diameter: 60.988 to 61.000 mm (2.4011 to 2.4016 in.)
If the diameter is not as specified, check the crankshaft oil clear-
ance
(c) Check each main journal for taper and out-of-round as
shown.
Maximum taper and out-of-round:
0.02 mm (0.0008 in.)
If the taper and out-of-round is greater than maximum, replace
the crankshaft.
(d) Using a micrometer, measure the diameter of each crank
pin.
Diameter: 52.992 to 53.000 mm (2.0863 to 2.0866 in.)
If the diameter is not as specified, check the connecting rod oil
clearance.
(e) Check each crank pin for taper and out-of-round as
shown.
Maximum taper and out-of-round:
0.02 mm (0.0008 in.)
If the taper and out-of-round is greater than maximum, replace
the crankshaft.
30. INSPECT CRANKSHAFT OIL CLEARANCE
HINT:
Crankshaft bearings come in widths of 22.4 mm (0.882 in.) and
19.0 mm (0.748 in.). Install the 22.4 mm (0.882 in.) bearings in
the No. 1 and No. 4 cylinder block journal positions with the
bearing caps. Install the 19.0 mm (0.748 in.) bearings in the No.
2 and No. 3 positions.
(a) Clean each main journal and bearing.
Page 545 of 969
A10529
A78810
1
3
4
5
6
7
8
2
10
11
13
12
14
15
16
9
A78811
Painted Mark
90
Front90
A78812
1
2
3
4
5
6
7
8
- ENGINE MECHANICALCYLINDER BLOCK ASSY (3MZ-FE)
14-169
2261 Author: Date:
2005 LEXUS ES330 REPAIR MANUAL (RM1124U)
(j) Using a plastic-faced hammer, lightly tap the bearing cap
to ensure proper fit.
(k) Apply a light coat of engine oil to the threads of the bear-
ing cap bolts.
(l) Using several steps, install and tighten the 16 bearing cap
bolts uniformly in the sequence shown in the illustration.
Torque: 22 NVm (224 kgfVcm, 16 ftVlbf)
(m) Mark the front side of the bearing cap bolts with paint.
(n) Retighten the bearing cap bolts by 90 in the same se-
quence as step (l).
(o) Check that each painted mark is now at a 90 angle to the
front.
NOTICE:
Do not turn the crankshaft.
(p) Using several steps, install and tighten the 8 bearing cap
bolts uniformly in the sequence shown in the illustration.
Torque: 27 NVm (275 kgfVcm, 20 ftVlbf)
HINT:
Use the short bolt for the position marked with the arrow.
(q) Remove the bearing caps.
Page 554 of 969
A78809Less than 6 mm (0.23 in.)
A10529
A78810
1
3
4
5
6
7
8
2
10
11
13
12
14
15
16
9
A78811
Painted Mark
90
Front90
A78812
1
2
3
4
5
6
7
8 14-178
- ENGINE MECHANICALCYLINDER BLOCK ASSY (3MZ-FE)
2270 Author: Date:
2005 LEXUS ES330 REPAIR MANUAL (RM1124U)
(d) Temporarily install the 8 bearing cap bolts to the inside
positions.
(e) Install the bearing cap by hand using the inner bolt as a
guide. Stop when the bearing cap is about 6 mm (0.23 in.)
away from contact with the cylinder block.
(f) Using a plastic-faced hammer, lightly tap the bearing cap
to ensure proper fit.
(g) Apply a light coat of engine oil to the threads of the bear-
ing cap bolts.
(h) Using several steps, install and tighten the 16 bearing cap
bolts uniformly in the sequence shown in the illustration.
Torque: 22 NVm (224 kgfVcm, 16 ftVlbf)
(i) Mark the front side of the bearing cap bolts with paint.
(j) Retighten the bearing cap bolts by 90 in the same se-
quence as step (h).
(k) Check that each painted mark is now at a 90 angle to the
front.
(l) Check that the crankshaft turns smoothly.
(m) Using several steps, install and tighten the 8 bearing cap
bolts uniformly in the sequence shown in the illustration.
Torque: 27 NVm (275 kgfVcm, 20 ftVlbf)
HINT:
Use the short bolt for the position marked with the arrow.
Page 555 of 969
A78322
Front Mark (Cavity)
Front
A78794
Protrusion Front
P12697
A78795
90
Front90Painted Mark
A78822
Front Side:
- ENGINE MECHANICALCYLINDER BLOCK ASSY (3MZ-FE)
14-179
2271 Author: Date:
2005 LEXUS ES330 REPAIR MANUAL (RM1124U)
42. INSTALL PISTON SUB-ASSY W/CONNECTING ROD
(a) Apply engine oil to the cylinder walls, pistons, and sur-
faces of the connecting rod bearings.
(b) Check the position of the piston ring ends.
(c) Using a piston ring compressor, push the numbered pis-
ton and connecting rod assemblies correctly into each
cylinder with the front mark of the piston facing forward.
NOTICE:
Match the numbered connecting rod cap with the connect-
ing rod.
(d) Check that the protrusion of the cap is facing the correct
direction.
(e) Apply a light coat of engine oil to the threads of the cap
bolts.
(f) Tighten the cap bolts in several steps by the specified
torque.
Torque: 25 NVm (250 kgfVcm, 18 ftVlbf)
(g) Mark the front side of each cap bolt with paint.
(h) Retighten the cap bolts by 90 as shown in the illustration.
(i) Check that the crankshaft turns smoothly.
43. INSTALL CYLINDER BLOCK W/HEAD STRAIGHT
SCREW NO.1 PLUG
(a) Using a socket hexagon wrench 10, install a new gasket
and the screw plug.
Torque: 30 NVm (306 kgfVcm, 22 ftVlbf)
Page 558 of 969
100IZ-01
A86347DLC3
Hand-held Tester
A86347DLC3
Hand-held Tester
- ENGINE CONTROL SYSTEMSFI SYSTEM (3MZ-FE)
10-1
2006 Author: Date:
2005 LEXUS ES330 REPAIR MANUAL (RM1124U)
SFI SYSTEM (3MZ-FE)
ON-VEHICLE INSPECTION
1. INSPECT CAMSHAFT TIMING OIL CONTROL VALVE
ASSY
(a) Check the operation.
(1) Connect the hand-held tester to the DLC3.
(2) Turn the ignition switch ON.
(3) Start the engine and allow it to warm up.
(4) Connect the hand-held tester, then select VVT from
the ACTIVE TEST menu.
(5) Check the engine speed when the OCV is operated
with the hand-held tester.
Standard:
Tester OperationSpecified Condition
OCV is OFFNormal engine speed
OCV is ONRough idle or engine stall
If the operation is not as specified, inspect the camshaft timing
oil control valve (see page 10-2).
2. INSPECT THROTTLE BODY ASSY
(a) Check the operation (throttle control motor).
(1) Turn the ignition switch ON.
(2) When turning the accelerator pedal position sensor
lever, check the running sound of the motor. Also,
check that there is no friction sound.
If the operation is not as specified, inspect the throttle body (see
page 10-2).
(b) Check the operation (throttle position sensor).
(1) Connect the hand-held tester to the DLC3.
(2) Turn the ignition switch ON.
(3) Check that the check engine warning light does not
light up.
(4) Check that the throttle valve opening percentage
(THROTTLE POS) of CURRENT DATA showns the
standard value.
Standard throttle valve opening percentage:
60 % or more
NOTICE:
When checking the standard throttle valve opening per-
centage, the transmission is in the neutral position.
3. INSPECT ACCELERATOR PEDAL POSITION SENSOR
(a) Inspect the voltage.
(1) After turning the ignition switch ON, check CURRENT DATA, then verify that the throttle position
sensor voltage is within the standard value.
Standard voltage: 0.6 to 1.0 V
If the voltage is not as specified, inspect the accelerator pedal (see page 10-2).
Page 559 of 969
100J0-01
A86282
Ohmmeter
A86283Battery Spool Valve
A84676Battery Voltmeter
Air 10-2
- ENGINE CONTROL SYSTEMSFI SYSTEM (3MZ-FE)
2007 Author: Date:
2005 LEXUS ES330 REPAIR MANUAL (RM1124U)
INSPECTION
1. INSPECT CAMSHAFT TIMING OIL CONTROL VALVE
ASSY
(a) Inspect the resistance.
(1) Using an ohmmeter, measure the resistance be-
tween the terminals.
Standard:
Tester ConnectionSpecified Condition
1 (-) - 2 (+)6.9 to 7.9 W at 20C (68F)
If the resistance is not as specified, replace the camshaft timing
oil control valve.
(b) Check the operation.
(1) Connect the positive (+) lead from the battery to ter-
minal 2 (+) and negative (-) lead to terminal 1 (-),
then check the movement of the spool valve.
NOTICE:
Confirm that the spool valve moves freely and does not get
stuck in any position.
HINT:
Bad returning of the spool valve resulted from catching foreign
objects causes subtle pressure leak to the advanced direction.
In that case, DTC can be detected.
2. INSPECT MASS AIR FLOW METER
(a) Check the operation.
(1) Apply battery voltage across terminals 1 (+B) and 2
(E2G).
(2) Using voltmeter, connect the positive (+) tester
probe to terminal 3 (VC), and negative (-) tester
probe to terminal 2 (E2G).
(3) Blow air into the mass air flow sensor, then check
that the voltage fluctuates.
If the operation is not as specified, replace the mass air flow
sensor.
Page 560 of 969
A84677
Ohmmeter
-20 0 20406080
(-4) (32) (68)(104)(140)(176)
Temperature C (F) 30
0.2 0.515 10 20
Resistance kW
A84678
Ohmmeter
-20 0 20406080
(-4) (32) (68)(104)(140)(176)
Temperature C (F) 30
0.2 0.515 10 20
Resistance kW
- ENGINE CONTROL SYSTEMSFI SYSTEM (3MZ-FE)
10-3
2008 Author: Date:
2005 LEXUS ES330 REPAIR MANUAL (RM1124U)
(b) Inspect the resistance.
(1) Using an ohmmeter, measure the resistance be-
tween the terminals.
Standard:
Tester ConnectionSpecified Condition
4 (THA) - 5 (E2)13.6 to 18.4 kW at -20C (-4F)
4 (THA) - 5 (E2)2.21 to 2.69 kW at 20C (68F)
4 (THA) - 5 (E2)0.493 to 0.667 kW at 60C (140F)
If the resistance is not as specified, replace the mass air flow
sensor.
3. INSPECT ENGINE COOLANT TEMPERATURE
SENSOR
(a) Inspect the resistance.
(1) Using an ohmmeter, measure the resistance be-
tween the terminals.
Standard:
Tester ConnectionSpecified Condition
1 (E2) - 2 (THW)2.32 to 2.59 kW at 20C (68F)
1 (E2) - 2 (THW)0.310 to 0.326 kW at 80C (176F)
NOTICE:
When checking the engine coolant temperature sensor in
water, be careful not to allow water to intrude into the termi-
nals. Then dry the engine coolant temperature sensor after
checking.
If the resistance is not as specified, replace the engine coolant
temperature sensor.
Page 563 of 969
100J1-01
A86244
(a)
(b)
RH Bank:
A86306
(a)
(b)
LH Bank: 10-6
- ENGINE CONTROL SYSTEMCAMSHAFT TIMING OIL CONTROL VALVE
ASSY (3MZ-FE)
2011 Author: Date:
2005 LEXUS ES330 REPAIR MANUAL (RM1124U)
CAMSHAFT TIMING OIL CONTROL VALVE ASSY (3MZ-FE)
REPLACEMENT
1. DISCONNECT ENGINE WIRE NO. 3 (BATTERY NEGATIVE TERMINAL)
2. REMOVE V-BANK COVER SUB-ASSY (See page 10-1 1)
3. REMOVE CAMSHAFT TIMING OIL CONTROL VALVE
ASSY
(a) Disconnect the 2 camshaft timing oil control valve con-
nectors.
(b) Remove the 2 bolts, then remove the 2 camshaft timing
oil control valves.
HINT:
The camshaft timing oil control valve is installed with the bolt.
4. INSTALL CAMSHAFT TIMING OIL CONTROL VALVE ASSY
(a) Apply a light coat of engine oil to the O-ring on each camshaft timing oil control valve.
(b) Install the 2 camshaft timing oil control valves with the 2 bolts.
Torque: 8.0 NVm (80 kgfVcm, 71 in.Vlbf)
NOTICE:
Be careful not to twist the O-ring.
(c) Connect the 2 camshaft timing oil control valve connectors.
5. INSTALL V-BANK COVER SUB-ASSY (See page 10-1 1)
6. CONNECT ENGINE WIRE NO. 3 (BATTERY NEGATIVE TERMINAL)
Torque: 5.4 NVm (55 kgfVcm, 48 in.Vlbf)
7. CHECK FOR ENGINE OIL LEAKS
8. SYSTEM INITIALIZATION (See page 19-15)
Page 565 of 969
100J3-02
A86247
(a)
(b)
Deep Socket
Wrench 19
10-8- ENGINE CONTROL SYSTEMENGINE COOLANT TEMPERATURE
SENSOR (3MZ-FE)
2013 Author: Date:
2005 LEXUS ES330 REPAIR MANUAL (RM1124U)
ENGINE COOLANT TEMPERATURE SENSOR (3MZ-FE)
REPLACEMENT
1. DISCONNECT ENGINE WIRE NO. 3 (BATTERY NEGATIVE TERMINAL)
2. REMOVE RADIATOR LOWER AIR DEFLECTOR (See page 19-5)
3. DRAIN ENGINE COOLANT (See page 16-9)
4. REMOVE ENGINE COOLANT TEMPERATURE
SENSOR
(a) Disconnect the engine coolant temperature sensor con-
nector.
(b) Using a deep socket wrench 19, remove the engine cool-
ant temperature sensor and gasket.
5. INSTALL ENGINE COOLANT TEMPERATURE SENSOR
(a) Using a deep socket wrench 19, install a new gasket and the engine coolant temperature sensor.
Torque: 20 NVm (200 kgfVcm, 14 ftVlbf)
(b) Connect the engine coolant temperature sensor connector.
6. CONNECT ENGINE WIRE NO. 3 (BATTERY NEGATIVE TERMINAL)
Torque: 5.4 NVm (55 kgfVcm, 48 in.Vlbf)
7. ADD ENGINE COOLANT (See page 16-9)
8. CHECK FOR ENGINE COOLANT LEAKS (See page 16-1)
9. INSTALL RADIATOR LOWER AIR DEFLECTOR
10. SYSTEM INITIALIZATION (See page 19-15)
Page 569 of 969
A86254
(d)
(d)
(d)
(d) 10-12
- ENGINE CONTROL SYSTEMTHROTTLE BODY ASSY (3MZ-FE)
2017 Author: Date:
2005 LEXUS ES330 REPAIR MANUAL (RM1124U)
(d) Remove the 4 bolts, then remove the throttle body.
(e) Remove the gasket from the intake air connector.
8. INSTALL THROTTLE BODY ASSY
(a) Install a new gasket to the intake air connector.
(b) Install the throttle body with the 4 bolts.
Torque: 11 NVm (112 kgfVcm, 8 ftVlbf)
(c) Connect the water by-pass hose No. 3.
(d) Connect the water by-pass hose No. 2.
(e) Connect the throttle motor connector.
9. INSTALL AIR CLEANER CAP SUB-ASSY
Torque: 5.0 NVm (51 kgfVcm, 44 in.Vlbf)
10. CHECK CONNECTION OF VACUUM HOSE (See page 14-29)
11. CONNECT ENGINE WIRE NO. 3 (BATTERY NEGATIVE TERMINAL)
Torque: 5.4 NVm (55 kgfVcm, 48 in.Vlbf)
12. ADD ENGINE COOLANT (See page 16-9)
13. CHECK FOR ENGINE COOLANT LEAKS (See page 16-1)
14. INSTALL V-BANK COVER SUB-ASSY
(a) Fit the 2 retainers, then install the V-bank cover.
(b) Using a socket hexagon wrench 5, tighten the 3 nuts.
Torque: 7.9 NVm (81 kgfVcm, 70 in.Vlbf)
15. INSTALL FRONT SUSPENSION UPPER BRACE CENTER (W/O TEMS)
Torque: 80 NVm (816 kgfVcm, 59 ftVlbf)
16. INSTALL RADIATOR LOWER AIR DEFLECTOR
17. SYSTEM INITIALIZATION (See page 19-15)