torque LEXUS ES300 2005 Manual Online
[x] Cancel search | Manufacturer: LEXUS, Model Year: 2005, Model line: ES300, Model: LEXUS ES300 2005Pages: 969, PDF Size: 24.08 MB
Page 221 of 969
D03547
D03547
C91927
D30865
C91925
40-22
- AUTOMATIC TRANSMISSION / TRANSTRANSMISSION WIRE (U151E)
2537 Author: Date:
2005 LEXUS ES330 REPAIR MANUAL (RM1124U)
5. REMOVE TRANSMISSION WIRE
(a) Disconnect the transmission wire connectors.
(b) Remove the bolt and transmission wire.
6. INSTALL TRANSMISSION WIRE
(a) Coat a O-ring of the transmission wire connector with
AT F.
(b) Install the transmission wire with the bolt.
Torque: 5.4 NVm (55 kgfVcm, 48 in.Vlbf)
7. CONNECT TRANSMISSION WIRE
(a) Coat a O-ring of the ATF temperature sensor with ATF.
(b) Install the ATF temperature sensor with the lock plate and
bolt.
Torque: 6.6 NVm (67 kgfVcm, 58 in.Vlbf)
(c) Connect the 7 shift solenoid valve connectors.
8. I N S TA L L A U TO M AT I C T R A N S A X L E O I L PA N
SUB-ASSY
(a) Install the 2 magnets in the oil pan.
(b) Apply seal packing to the 18 bolts.
Seal packing:
THREE BOND 2430 or equivalent
(c) Install a new gasket, oil pan and 18 bolts to the transaxle
case.
Torque: 7.8 NVm (80 kgfVcm, 69 in.Vlbf)
NOTICE:
Since the bolts should be seal bolts, apply seal packing to
the bolts and tighten them within 10 minutes after applying.
Page 223 of 969
4010W-04
C91925
D30865
AT0103
C91927
40-24
- AUTOMATIC TRANSMISSION / TRANSTRANSMISSION VALVE BODY ASSY (U151E)
2539 Author: Date:
2005 LEXUS ES330 REPAIR MANUAL (RM1124U)
TRANSMISSION VALVE BODY ASSY (U151E)
REPLACEMENT
1. REMOVE ENGINE UNDER COVER NO.1
2. DRAIN AUTOMATIC TRANSAXLE FLUID
(a) Remove the drain plug, gasket, and drain ATF.
(b) Install a new gasket and drain plug.
Torque: 49 NVm (500 kgfVcm, 36 ftVlbf)
3. REMOVE AUTOMATIC TRANSAXLE OIL PAN
SUB-ASSY
(a) Remove the 18 bolts, oil pan and gasket.
NOTICE:
Some fluid will remain in the oil pan. Remove all the pan
bolts, and carefully remove the oil pan assembly.
(b) Remove the 2 magnets from the oil pan.
(c) Examine particles in pan.
(1) Use the removed magnets to collect steel chips.
Look carefully at the chips and particles in the pan
and the magnet to anticipate the type of wear you
will find in the transaxle.
Steel (magnetic): bearing, gear and plate wear
Brass (non-magnetic): bearing wear
4. DISCONNECT TRANSMISSION WIRE
(a) Disconnect the 7 shift solenoid valve connectors.
(b) Remove the bolt and lock plate, and disconnect the ATF
temperature sensor.
Page 225 of 969
D30644
G30205
D30644
AB
B
C
D
40-26
- AUTOMATIC TRANSMISSION / TRANSTRANSMISSION VALVE BODY ASSY (U151E)
2541 Author: Date:
2005 LEXUS ES330 REPAIR MANUAL (RM1124U)
(c) Remove the 5 bolts and 7 shift solenoid valves.
7. INSTALL TRANSMISSION VALVE BODY ASSY
(a) Install the spring and check ball body.
(b) Install the 7 shift solenoid valves with the 5 bolts.
Torque:
Bolt A, B: 11 N´m (110 kgf´cm, 8 ft.Vlbf)
Bolt C, D: 6.6 N´m (67 kgf´cm, 58 in. lbf)
Bolt length:
Bolt A: 16 mm (0.63 in.)
Bolt B: 57 mm (2.2 in.)
Bolt C: 23 mm (0.9 in.)
Bolt D: 12 mm (0.47 in.)
Page 226 of 969
C91933
A
B
CB
B
B
A
CCC
C
B
C91932
C91931
C91927
- AUTOMATIC TRANSMISSION / TRANSTRANSMISSION VALVE BODY ASSY (U151E)
40-27
2542 Author: Date:
2005 LEXUS ES330 REPAIR MANUAL (RM1124U)
(c) Align the groove of the manual valve with the pin of lever.
(d) Install the 17 bolts.
Torque: 11 NVm (110 kgfVcm, 8 ftVlbf)
NOTICE:
Push the valve body against the accumulator piston
spring and the check ball body to install it.
Temporarily tighten those bolts marked by in the il-
lustration first because they are positioning bolts.
Bolt length:
Bolt A: 25 mm (0.984 in.)
Bolt B: 57 mm (2.244 in.)
Bolt C: 41 mm (1.614 in.)
8. INSTALL VALVE BODY OIL STRAINER ASSY
(a) Coat a new O-ring with ATF.
(b) Install the O-ring to the oil strainer.
(c) Install the oil strainer with the 3 bolts.
Torque: 11 NVm (110 kgfVcm, 8 ftVlbf)
9. INSTALL TRANSMISSION WIRE
(a) Coat a O-ring with ATF.
(b) Install the ATF temperature sensor with the lock plate and
bolt.
Torque: 6.6 NVm (67 kgfVcm, 58 in.Vlbf)
(c) Connect the 7 shift solenoid valve connectors.
Page 227 of 969
D30865
C91925
40-28
- AUTOMATIC TRANSMISSION / TRANSTRANSMISSION VALVE BODY ASSY (U151E)
2543 Author: Date:
2005 LEXUS ES330 REPAIR MANUAL (RM1124U)
10. I N S TA L L A U TO M AT I C T R A N S A X L E O I L PA N
SUB-ASSY
(a) Install the 2 magnets in the oil pan.
(b) Apply seal packing to 18 bolts.
Seal packing:
THREE BOND 2430 or equivalent
(c) Install a new gasket, oil pan and 18 bolts to the transaxle
case.
Torque: 7.8 NVm (80 kgfVcm, 69 in.Vlbf)
NOTICE:
Since the bolts should be seal bolts, apply seal packing to
the bolts and tighten them within 10 minutes after applying.
11. ADD AUTOMATIC TRANSAXLE FLUID
12. INSPECT AUTOMATIC TRANSAXLE FLUID (SEE PAGE 40-1)
13. INSTALL ENGINE UNDER COVER NO.1
14. RESET MEMORY (SEE PAGE 05-604)
Page 228 of 969
4010X-04
D25831
SST
D25832
SST
D25833
SST
- AUTOMATIC TRANSMISSION / TRANSFRONT DIFFERENTIAL OIL SEAL (U151E)
40-29
2544 Author: Date:
2005 LEXUS ES330 REPAIR MANUAL (RM1124U)
FRONT DIFFERENTIAL OIL SEAL (U151E)
REPLACEMENT
1. REMOVE FRONT WHEELS
2. REMOVE ENGINE UNDER COVER NO.1
3. DRAIN AUTOMATIC TRANSAXLE FLUID
(a) Remove the drain plug, gasket and drain ATF.
(b) Install a new gasket and drain plug.
Torque: 49 NVm (500 kgfVcm, 36 ftVlbf)
4. REMOVE FRONT DRIVE SHAFT ASSY RH (SEE PAGE 30-8)
5. REMOVE FRONT DRIVE SHAFT ASSY LH (SEE PAGE 30-8)
6. REMOVE TRANSAXLE HOUSING OIL SEAL
(a) Using SST, pull out the oil seal.
SST 09308-00010
7. REMOVE DIFFERENTIAL SIDE BEARING RETAINER
OIL SEAL
(a) Using SST, pull out the oil seal.
SST 09308-00010
8. INSTALL DIFFERENTIAL SIDE BEARING RETAINER
OIL SEAL
(a) Using SST and a hammer, drive in a new oil seal.
SST 09316-6001 1 (09316-00011)
Oil seal drive in depth:
0 0.5 mm (0 0.020 in.)
(b) Coat the lip of the oil seal with MP grease.
SST 09316-6001 1 (09316-00011)
Page 237 of 969
C93021
C93024
C93016
C93149
40-38
- AUTOMATIC TRANSMISSION / TRANSFLOOR SHIFT ASSY
2553 Author: Date:
2005 LEXUS ES330 REPAIR MANUAL (RM1124U)
36. INSTALL SHIFT LOCK RELEASE BUTTON COVER
(a) Install the shift lock release button cover to the position in-
dicator housing.
37. INSTALL SHIFT LEVER KNOB SUB-ASSY
(a) Install the floor shift lever knob to the shift lever.
38. INSTALL FLOOR SHIFT ASSY
(a) Install the floor shift assy to the vehicle with the 4 bolts.
Torque: 11.8 NVm (122 kgfVcm, 9 ftVlbf)
(b) Connect the shift lock control computer.
(c) Connect the indicator lamp wire connector.
39. INSTALL TRANSMISSION CONTROL CABLE ASSY
(a) Install the floor shift transmission control cable to the shift
lever.
HINT:
Install it with the uneven surface facing up.
Page 239 of 969
400H6-03
D25118
D25119
40-40
- AUTOMATIC TRANSMISSION / TRANSFLOOR SHIFT ASSY
2555 Author: Date:
2005 LEXUS ES330 REPAIR MANUAL (RM1124U)
ADJUSTMENT
1. INSPECT SHIFT LEVER POSITION
(a) When shifting from P to R position only with ignition switch ON and brake pedal, make sure that the
shifting lever moves smoothly and can be moderately operated.
(b) When starting engine, make sure that the vehicle moves forward when shifting from N to D position
and moves rearward when shifting to R position.
2. ADJUST SHIFT LEVER POSITION
(a) Loosen the nut on the control shaft lever.
(b) Push the control shaft fully downward.
(c) Return the control shaft lever 2 notches to N position.
(d) Set the shift lever to N position.
(e) While holding the shift lever lightly toward the R position
side, tighten the shift lever nut.
Torque: 14.7 N´m (150 kgf´cm, 10 ft´lbf)
(f) Start the engine and make sure that the vehicle moves
forward when shifting the lever from N to D position and
moves rearward when shifting it to R position.
Page 245 of 969
C90581
C93327
D25414
D25415
40-46
- AUTOMATIC TRANSMISSION / TRANSTRANSMISSION CONTROL CABLE ASSY
2561 Author: Date:
2005 LEXUS ES330 REPAIR MANUAL (RM1124U)
(d) Install the shift cable grommet retainer No.2 with the 2
bolts.
Torque: 4.9 NVm (50 kgfVcm, 43 in.Vlbf)
(e) Connect the control cable to the control cable clamp.
(f) Temporarily install the control cable to the control shaft le-
ver with nuts.
(g) Install the control cable and a new clip to the bracket.
10. INSTALL INTAKE AIR RESONATOR SUB-ASSY
11. INSTALL AIR CLEANER HOSE NO.1
12. INSTALL AIR CLEANER ASSY
13. INSTALL AIR BAG SENSOR ASSY CENTER (SEE PAGE 60-55)
14. INSTALL AIR CONDITIONING RADIATOR ASSY (SEE PAGE 55-17)
15. INSTALL INSTRUMENT PANEL SAFETY PAD SUB-ASSY (SEE PAGE 71-1 1)
16. INSTALL BATTERY
17. ADJUST SHIFT LEVER POSITION (SEE PAGE40-40)
18. INSPECT SHIFT LEVER POSITION (SEE PAGE40-40)
Page 249 of 969
3211W-03
F41694
F41695
F41696
C80826
32-4
- BRAKEBRAKE FLUID
2438 Author: Date:
2005 LEXUS ES330 REPAIR MANUAL (RM1124U)
BRAKE FLUID (From July, 2003)
BLEEDING
HINT:
If any work is done on the brake system or if air in the brake lines is suspected, bleed the air from the system.
NOTICE:
Wash off the brake fluied immediately if it comes into contact with a painted surface.
1. FILL RESERVOIR WITH BRAKE FLUID
Fluid: SAE J1703 or FMVSS No. 116 DOT3
2. BLEED MASTER CYLINDER
HINT:
If the master cylinder has been disassembled or if the reservoir
becomes empty, bleed the air from the master cylinder.
(a) Remove the air cleaner assembly with hose.
(b) Disconnect the brake lines from the master cylinder.
SST 09023-00101
(c) Slowly depress the brake pedal and hold it.
(d) Block off the outer holes with your fingers, and release the
brake pedal.
(e) Repeat (c) and (d) 3 or 4 times.
(f) Install the air cleaner assembly with hose.
3. BLEED BRAKE LINE
(a) Connect the vinyl tube to the brake caliper.
(b) Depress the brake pedal several times, then loosen the
bleeder plug with the pedal held down.
(c) At the point when fluid stops coming out, tighten the
bleeder plug, then release the brake pedal.
(d) Repeat (b) and (c) until all the air in the fluid has been bled
out.
(e) Tighten the bleeder plug certainly.
Torque: 8.3 NVm (85 kgfVcm, 73 in.Vlbf)