lock Lexus GS250 2012 Owner's Manual

715 6-3. Do-it-yourself maintenance
6
Maintenance and care
GS350/250_EE (OM30C36E)
15LH-IG210
Multiport fuel injection system/sequen-
tial multiport fuel injection system, stop
lights, smart entry & start system, steer-
ing lock system
16LH J/B-B7.5Body ECU
17S/ROOF20Moon roof
18P/SEAT2 F/L25Power seats
19A/C7.5Air conditioning system
FuseAmpereCircuit

7186-3. Do-it-yourself maintenance
GS350/250_EE (OM30C36E)
Right-hand drive vehicles
FuseAmpereCircuit
1STOP7.5Stop lights, high mounted stoplight
2P/SEAT1 F/R30Power seats
3FR P/OUTLET15Power outlet (front)
4P/W-B5Power window master switch
5RR P/OUTLET15Power outlet (rear)
6P/SEAT2 F/R25Power seats
7AV S20AV S
8WIPER30Windshield wipers
9WA S H20Windshield washer
10RH ECU-IG10
Navigation system, VDIM, D-SW
MODULE (Blind Spot Monitor, heated
steering wheel)
11RH-IG10
Tension reducer, AWD system, power
seats, head-up display, front right-hand
door ECU, nanoe, shift lock system,
electric tilt and telescopic steering col-
umn, seat heater/ventilator switches,
smart entry & start system antennas, tire
pressure warning system receiver, driver
monitor system
12DOOR FR30
Front right-hand door control system
(outside rear view mirror defoggers,
power window)

719 6-3. Do-it-yourself maintenance
6
Maintenance and care
GS350/250_EE (OM30C36E)
13DOOR RR30Power window (rear right-hand)
14RAD NO.230Audio system
15STRG LOCK15Steering lock system
16MULTIMEDIA10Navigation system, Remote Touch
17RAD NO.130Audio system
18AIR BAG10SRS airbag system
19OBD7.5On-board diagnosis system
20TI & TE20Electric tilt and telescopic steering col-
umn
21ACC7.5
Body ECU, head-up display, RR CTRL,
navigation system, transmission, Remote
Touch, Remote Touch screen
FuseAmpereCircuit

7246-3. Do-it-yourself maintenance
GS350/250_EE (OM30C36E)
Front fog lights (if equipped)
To allow enough working
space, turn the steering
wheel to the opposite side
of the bulb to be replaced.
Remove the 2 fender liner
clips.
Turn the steering wheel to the
left when replacing the right
side light bulb, and turn the
steering wheel to the right when
replacing the left side light bulb.
To take out the clips, turn the
head of the clip to unlock, then
remove by pulling.
While holding the clamp
open, pull and remove the
tabs and open the fender
liner.
Unplug the connector while
pressing the lock release.
Replacing light bulbs
1
2
3

725 6-3. Do-it-yourself maintenance
6
Maintenance and care
GS350/250_EE (OM30C36E)Turn the bulb base counter-
clockwise.
Set the new light bulb.
Align the 3 tabs on the light
bulb with the mounting, and
insert. Turn it clockwise to set.
Set the connector.
After installing the connector,
shake the bulb base gently to
check that it is not loose, turn
the fog lights on once and visu-
ally confirm that no light is
leaking through the mounting.
Reinstall the fender liner
and install the clips.
Insert the clips and turn to lock.
4
5
6
7

7266-3. Do-it-yourself maintenance
GS350/250_EE (OM30C36E)
Front turn signal lights
For the left side only: To
allow enough working
space, turn the steering
wheel all the way to the
right, then remove the bolts
and take off the cover.
Turn the bulb base counterclockwise.
1
2
Right sideLeft side

7286-3. Do-it-yourself maintenance
GS350/250_EE (OM30C36E)
Rear turn signal lights
Open the trunk lid and
remove the cover.
Turn the bulb base counter-
clockwise.
Remove the light bulb.
When installing, reverse the
steps listed.
After installing the bulb base,
secure the cord with the clips
and install the cover in its origi-
nal position.
1
2
3
4

729 6-3. Do-it-yourself maintenance
6
Maintenance and care
GS350/250_EE (OM30C36E)
Back-up light
Open the trunk lid.
For the left side (vehicles
with power trunk lid only):
Pry out each side of the
trunk closer switch in turn
by inserting a screwdriver
into the base.
To prevent damage, cover the
tip of the screwdriver with a rag.
Remove the clips on which-
ever side you are replacing
and open the cover of the
trunk lid.
Turn the bulb base counter-
clockwise.
1
2
3
4

7326-3. Do-it-yourself maintenance
GS350/250_EE (OM30C36E)Remove the screws and take
off the mirror cover.
Turn the bulb base counter-
clockwise.
Remove the light bulb.
After installing the new
bulb, secure the socket to
the light body.
When inserting the socket, align
the marks printed on the light
body and the socket.
4
5
6
7

733 6-3. Do-it-yourself maintenance
6
Maintenance and care
GS350/250_EE (OM30C36E)Install the visor cover on the
mirror frame, secure it with
a screw, and install the side
turn signal light and outer
foot light.
Use only the screw position
shown in the illustration.
Side turn signal light: Align the
tabs on the light and the cover
and install.
Outer foot light: Interlock the
tabs in the groove of the light
body with those on the cover,
and secure.
Disconnect the tabs, and
separate the top and bottom
of the rear side cover of the
mirror.
8
9