brake fluid Lexus GS300 1995 Chassis

SECTION 6 – 3
185
SERVICE PROCEDURES AND
SPECIFICATIONS
Chassis
Specifications186 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Checking brake fluid188 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Checking power steering fluid189 . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Checking tire pressure190 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Rotating tires191 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Checking and replacing tires191 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Installing snow tires and chains193 . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Replacing wheels194 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Aluminum wheel precautions195 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

CHASSIS
186
SPECIFICATIONS
− AUTOMATIC TRANSMISSION
Fluid capacity
Drain and refill
Fluid type
1.9 L (2.0 qt., 1.7 Imp.qt.)
Automatic transmission fluid Type T − II or equivalent
− DIFFERENTIAL
Oil capacity
Oil type
Oil viscosity
1.35 L (1.42 qt., 1.19 Imp.qt.)
Hypoid gear oil API GL−5
Above −18
C (0
F): SAE 90
Below −18
C (0
F): SAE 80 W or SAE 80 W−90
− BRAKES
Pedal clearance
Pedal freeplay
Brake pad wear limit
Parking brake lining wear limit
Parking brake adjustment
Fluid type
75 mm (3.0 in.) Min.
1 − 6 mm (0.04 − 0.24 in.)
1.0 mm (0.04 in.)
1.0 mm (0.04 in.)
5 − 7 clicks
SAE J1703 or FMVSS No. 116 DOT 3

CHASSIS
188
CHECKING BRAKE FLUID
Brake fluid reservoir
with traction control system
Brake fluid reservoir
Maximum
level line
Brake fluid reservoir
Maximum level line
Brake fluid reservoir
without traction control system
To check the fluid level, simply look at the see−through
reservoir. The level should be between the “MAX” and
“MIN” lines on the tank.It is normal for the brake fluid level to go down slightly as the
brake pads wear. So be sure to keep the reservoir filled.
If the reservoir needs frequent refilling, it may indicate a
serious mechanical problem.
If the level is low, add FMVSS No.116 DOT 3 or SAE J1703
brake fluid to the brake reservoir.
Remove and replace the reservoir cover by hand. Add brake
fluid up to the “MAX” line.
Use only newly opened brake fluid. Once opened, brake fluid
absorbs moisture from the air, and excess moisture can cause
a dangerous loss of braking efficiency.
CAUTION:
Take care when filling the reservoir because brake fluid
can harm your eyes and damage painted surfaces. If fluid
gets in your eyes, flush your eyes with clean water.
NOTICE (For vehicles with traction control system only):
Idle the engine while pouring brake fluid into the
reservoir.