reset Lexus GS300 2006 Audio

AUDIO
275
1
Audio operation screen display button
The audio operation screen is shown.
2
Function switch display screen
(See page 280 for details.)
3
CD slot
(See page 300 or details.)
4
Mode selectors
(See page 279 for details.)
5
Frequency turning knob
(See page 285 for details.)
6
CD load button
(See page 300or details.)
7
Radio mode:Preset tuning
(See page 285 for details.)
Tape mode:Side change of cassette tape
(See page 298 for details.)
CD mode:Disc selection
(See page 303 for details.)
8
Scan button
(See page 286 for details.)
9
Cassette tape slot
(See page 296 for details.)
10Stopping and ejecting a cassette tape
(See page 296 for details.)
11Radio mode:Seek tuning
(See page 286 for details.)
Tape/CD mode:Direct access to a desired
program
(See page 299 or 304 for details.)
12Ejecting a CD
(See page 301 or details.)
13Turning the system on and adjusting the volume
(See page 279 for details.)

AUDIO
277
1
Audio operation screen display button
The audio operation screen is shown.
2
Touch screen
(See page 280 for details.)
3
Disc slot
(See page 300 or details.)
4
Mode selectors
(See page 279 for details.)
5
Frequency turning knob
(See page 285 for details.)
6
Disc load button
(See page 300or details.)
7
Radio mode:Preset tuning
(See page 285 for details.)
Tape mode:Side change of cassette tape
(See page 297 for details.)
DISC mode:Disc selection
(See page 303 for details.)
8
Scan button
(See page 286 for details.)
9
Cassette tape slot
(See page 296 for details.)
10Stopping and ejecting a cassette tape
(See page 296 for details.)
11Radio mode:Seek tuning
(See page 286 for details.)
Tape/DISC
mode:Direct access to a desired
program
(See page 299 or 304 for details.)
12Ejecting a disc
(See page 301 or details.)
13Turning the system on and adjusting the volume
(See page 279 for details.)

AUDIO
285
G22010
Turn this knob to step up or down the frequency.
Your radio automatically changes to stereo reception when a
stereo broadcast is received. “ST” appears on the display. If
the signal becomes weak, the radio reduces the amount of
channel separation to prevent the weak signal from creating
noise. If the signal becomes extremely weak, the radio
switches from stereo to mono reception. In this case, “ST”
disappears from the display.(b) Presetting a station
G22004
1. Tune in the desired station.
2. Touch one of the station selector switches (1−6) and
hold it until a beep is heard. This sets the station to the
switch and the frequency appears on the switch.
Each switch can store AM, FM1 and FM2. To change the
preset station to a different one, follow the same procedure.
The preset station memory is cancelled when the power
source is interrupted by battery disconnection or a blown fuse.

AUDIO
286(c) Selecting a station
Your Lexus has an electronic tuning radio (ETR). Tune in the
desired station using one of the following methods.
G22073
Preset tuning: Touch the switch (1−6) or push the “CH DISC
” or “ ” button for the station you want. The switch (1−6)
is highlighted in green and station frequency appears on the
display.
Manual tuning: Turn the “TUNE” knob briefly. When you turn
the knob, the radio will step up or down to another frequency.
Seek tuning: Push the “SEEK TRACK
” or “ ” button.
The radio will begin seeking up or down for a station of the
nearest frequency and will stop on reception. Each time you
push the button, the stations will be searched out one after
another.
G22021
Scan tuning:Push the “SCAN” button. “SCAN” appears on
the display. The radio will find the next station up or down the
band, stay there for a few seconds, and then scan again. To
select a station, push the “SCAN” button a second time.
Preset scan tuning: Push the “SCAN” button and hold it until
you hear a beep. “P. SCAN” appears on the display. The radio
will tune in the next preset station up or down the band, stay
there for a few seconds, and then move to the next preset
station. To select a station, push the “SCAN” button a second
time.

AUDIO
291 (d) Presetting a channel
G22015
1. Tune in the desired channel.
2. Touch one of the channel selector switches (1−6) and
hold it until a beep is heard. This sets the channel to the
switch and the frequency appears on the switch.
Each switch can store three SAT channels. To change the
preset channel to a different one, follow the same procedure.
The preset channel memory is cancelled when the power
source is interrupted by battery disconnection or a blown fuse.(e) Selecting a channel
Tune in the desired channel using one of the following
methods.
Preset tuning: Touch the switch (1−6) or push the “CH DISC
” or “ ” bu t t o n for the channel you want. The switch (1−6)
is highlighted in green.
Manual tuning within the channel category: Turn the
“TUNE” knob. The radio will step up or down the channel.
Manual tuning within the current channel category: Push
the “SEEK TRACK
” or “ ” button. The radio will step up
or down the channel within the current channel category.
Touch the “TYPE SEEK” switch. The radio will step up the
channel within the current channel category.

AUDIO
292
G22016
To scan the currently selected channel category: Touch the
“TYPE SCAN” switch or push the “SCAN” button briefly.
“SCAN” appears on the display. The radio will find the next
channel in the same channel category, stay there for a few
seconds, and then scan again. To select a channel, push the
“SCAN” button a second time.
To scan the preset channels: Touch the “TYPE SCAN”
switch or push the “SCAN” button and hold it until you hear a
beep. “P.SCAN” appears on the display. The radio will find the
next preset channel, stay there for a few seconds, and then
move to the next preset channel. To select a channel, push the
“SCAN” button a second time.(f) Channel category
G22017
Touch either “TYPE” or “TYPE ” switch to switch to the next
or previous category.

AUDIO
305 (g) Other CD player functions
G22072
“RPT” switch: Use it for automatic repeat of the track you are
currently listening to.
Touch the switch while the track is playing. When the track is
finished, the player will automatically go back to the beginning
of the track and play the track again. To cancel it, touch the
switch once again.
“DISC RPT” switch: Use it for automatic repeat of the disc you
are currently listening to.
Touch the switch while the disc is playing. When the disc is
finished, the player will automatically go back to the beginning
of the disc and play the disc again. To cancel it, touch the
button once again.“DISC RAND” switch: Use it for automatic track selection for
all the discs and play by the system.
When the switch is touched, the system selects a track in all
the discs which are set and plays it. To cancel it, touch the
switch once again.
When a track is skipped or the system is inoperative, touch the
switch to reset.
“RAND” switch: Use it for automatic and random selection
of the disc which you are currently listening to.
When the switch is touched, the system selects a track in the
disc you are currently listening to. To cancel it, touch the switch
once again.
“TITLE” switch: Use it for displaying the disc title and track
title while the CD−TEXT disc is playing.