radio Lexus GS300 2006 Starting and Driving
[x] Cancel search | Manufacturer: LEXUS, Model Year: 2006, Model line: GS300, Model: Lexus GS300 2006Pages: 110, PDF Size: 2.22 MB
Page 7 of 110
STARTING AND DRIVING
345 “ACC” mode
G31033
This mode allows some accessories to be operable such
as the radio, even if the engine is not running. An amber
indicator light turns on at the engine switch.
To select the “ACC” mode from “OFF” mode, push the engine
switch once without depressing the brake pedal. The engine
immobilizer is disabled and the security indicator light goes
out. (For details, see “Engine immobilizer” on page 11.)
If you cycle once through all the modes (“OFF”, “ACC”,
“IG−ON”) with the driver’s door closed, the second time you
select the “ACC” mode, the above message will appear for a
few seconds.
If the vehicle is left in “ACC” mode for about an hour, the engine
switch is automatically off.
If the driver’s door is opened with the transmission in “P”, a
buzzer will remind you in “ACC” mode.“IG−ON” mode
G31034
“IG−ON” mode has two conditions: all gauges, meters
and accessories on and the engine is not running, or
engine running.
To select the “IG−ON” mode while the engine is not running:
From “OFF” mode—push the engine switch twice without
depressing the brake pedal.
From “ACC” mode—push the engine switch once without
depressing the brake pedal.
The engine switch indicator light will be illuminated amber if the
engine is not running, and will turn off when the engine is
running.
Page 39 of 110
STARTING AND DRIVING
377 NOTE:
* The detection range can be changed from about 50 cm
(1.5 ft.) for dual sensors and about 60 cm (2 ft.) for back
sensors.
Ask your Lexus dealer for details.
The intuitive parking assist may not work properly in the
following cases:
When the bumper is damaged.
When the part near the sensors is subjected to a strong
impact.
When an accessory is installed within the sensor detection
range.
When snowflakes or mud gets on the sensors.
(If removed, the system will work properly.)
When water is splashed from a high pressure car wash or
steam on the sensors.
When a sensor is covered with your hand.
When the vehicle is tilted.
In extreme hot or cold weather
(In extreme cold weather, the error display appears and the
system becomes inoperative.)
When driving on bumpy roads, slopes, gravelled roads or
grass.Devices issuing ultrasonic waves are operated around your
vehicle, such as a horn from another vehicle, motorcycle
engine, air braking sound from heavy−duty vehicles.
When another vehicle equipped with ultrasonic sensors
gets close to your vehicle.
When heavy rain or water is splashed over the vehicle.
(Drive carefully as the braking distance may be affected.)
When a radio antenna or fender pole is mounted on your
vehicle.
If towing eyelet is installed on your vehicle.
When you are driving towards a tall curb stone or curb stone
having right angle.
The detection range for an object such as a traffic sign may
be shortened.
An object just under the bumper cannot be detected.
Although an object lower than the location of sensors is
once detected, the detection might be stopped when your
vehicle gets closer to the object.
When an obstacle is very close to the sensors.
Page 99 of 110
STARTING AND DRIVING
437
NOTICE
Do not use liquid sealants for a flat tire as tire
pressure sensors will be damaged.
When the tires must be repaired or replaced, have
them repaired or replaced by the nearest Lexus
dealer or authorized tire dealer. The tire pressure
sensors will be affected by the installation or removal
of tires.
When the tires must be replaced, replace the
grommets for tire pressure sensors as well.
System malfunction
G31048
If the low tire pressure warning light blinks and the above
message appears on the multi−information display, it
indicates a system malfunction. Contact your Lexus
dealer.
The system will be disabled in the conditions below:
Electric devices or facilities using similar radio wave
frequencies are nearby.
If a radio set at similar frequencies is in use.
Much snowflakes or ice gets on the vehicle, in particular,
around the wheels or wheel housings.
Non−genuine Lexus wheels are used.
Snow tires or tire chains are used.
The sensor battery is expired.
The tires not equipped with tire pressure sensor are used.
Page 100 of 110
STARTING AND DRIVING
438Although the tires are equipped with tire pressure sensors,
the selector switch (see page 442) is set to other tire setting.
NOTICE
The use of non−genuine wheels will cause the tire
pressure sensors to transmit the electronic code in
different manner, resulting in the failure of the
system.
The use of tires other than originally installed with
genuine wheels may also cause the malfunction of
the system.
For vehicles sold in U.S.A.
This device complies with Part 15 of the FCC Rules.
Operation is subject to the following two conditions: (1)
This device may not cause harmful interference, and (2)
this device must accept any interference received,
including interference that may cause undesired
operation.
NOTICE:
This equipment has been tested and found to comply
with the limits for a Class B digital device, pursuant to
Part 15 of the FCC Rules. These limits are designed to
provide reasonable protection against harmful
interference in a residential installation. This equipment
generates, uses and can radiate radio frequency
energy and, if not installed and used in accordance with
the instructions, may cause harmful interference to
radio communications. However, there is no guarantee
that interference will not occur in a particular
installation. If this equipment does cause harmful
interference to radio or television reception, which can
be determined by turning the equipment off and on, the
user is encouraged to try to correct the interference by
one or more of the following measures:
Reorient or relocate the receiving antenna.
Increase the separation between the equipment and
receiver.
Page 101 of 110
STARTING AND DRIVING
439
Connect the equipment into an outlet on a circuit
different from that to which the receiver is connected.
Consult the dealer or an experienced radio / TV
technician for help.
FCC WARNING:
Changes or modifications not expressly approved
by the party responsible for compliance could void
the user’s authority to operate the equipment.
For vehicles sold in Canada
Operation is subject to the following two conditions: (1)
this device may not cause interference, and (2) this
device must accept any interference, including
interference that may cause undesired operation of the
device.
Replacing tires and wheels
As you might have difficulty in locating a flat or deflated
tire, a tire pressure warning system should be installed on
the tires of this vehicle.
When replacing the wheels, be sure to install tire pressure
sensors on the wheels.
There are 3 ways to set up the tire pressure sensors:
a. Remove the sensor from the old wheel and install it to the
new wheel.
b. Keep the same wheel with tire pressure sensor and replace
the tire alone.
c. Use a new wheel and sensor.
You have to register an ID code for a new sensor. Up to 2
sets of codes can be registered. As one ID for the originally
installed sensor is registered at “MAIN” of the selector
switch, use the “2nd” position to register an ID for the new
sensor.
You do not need to re−register the ID code for any other
replacements. For the use of the originally installed tires,
put the selector switch at “MAIN” and for the use of tires set
purchased later, put the switch at “2nd”. For the sensor
selector switch, see page 442.