lock LEXUS GS400 2000 Service Owners Manual

BE0GD±10
I01372
Ignition SwitchRadio Assembly Tweeter
Front Speakers
Rear Speakers
Tweeter
Radio Assembly LEXUS Navigatioin
System Woofer
Power Amplifier
(NAKAMICHI made)
Driver Side Junction Block

RAD NO.2 FuseEngine Room No.1
Junction Block

ECU±B1 Fuse

RAD NO.1 Fuse
Passenger Side
Junction Block

DOME Fuse CD Auto ChangerCD Magazine
Power Amplifier
(PIONEER made)
BE±216
± BODY ELECTRICALAUDIO SYSTEM
2517 Author: Date:
2000 LEXUS GS300/GS400 (RM718U)
LOCATION
The vehicle shown in this illustration is ºGS400º.
All components of ºGS300º other than the ones used for engine are same as ºGS400º.

BE0GE±03
I04310
Wire Harness Side
I04189
Wire Harness Side
Connector ºBº
Connector ºDº Connector ºCº Connector ºAº
± BODY ELECTRICALAUDIO SYSTEM
BE±217
2518 Author: Date:
2000 LEXUS GS300/GS400 (RM718U)
INSPECTION
1. Except NAKAMICHI made:
INSPECT CD AUTO CHANGER CIRCUIT
Disconnect connectors from CD auto changer and inspect the
connector on the wire harness side.
Tester connectionConditionSpecified condition
8 ± GroundConstantContinuity
5 ± GroundConstantBattery positive voltage
10 ± GroundIgnition switch LOCKNo voltage
10 ± GroundIgnition switch ACC or ONBattery positive voltage
If the circuit is not as specified, inspect the circuits connected
to other parts.
HINT:

Check the wire harness between the radio receiver as-
sembly and the CD auto changer.

Since the signals to and from the MUTE, R±, R+, L±, L+,
TX
± and TX+ terminals are serial signals, they cannot or-
dinarily be measured with a tester.
2. Except NAKAMICHI made:
INSPECT POWER AMPLIFIER CIRCUIT
Disconnect the connector from power amplifier and inspect the
connector on the wire harness side.
Tester connectionConditionSpecified condition
B7 ± GroundConstantContinuity
C12 ± GroundIgnition switch LOCK and radio switch ONNo voltage
C12 ± GroundIgnition switch ACC or ON and radio switch ONBattery positive voltage
B4 ± GroundConstantBattery positive voltage
If the circuit is not as specified, inspect the circuits connected
to other parts.

I04190
Wire Harness Side
Connector ºAº Connector ºBº BE±218
± BODY ELECTRICALAUDIO SYSTEM
2519 Author: Date:
2000 LEXUS GS300/GS400 (RM718U)
3. Except NAKAMICHI made:
INSPECT RADIO RECEIVER ASSEMBLY CIRCUIT
Disconnect the connectors from the radio receiver assembly,
and inspect the connector on the wire harness side.
Tester connectionConditionSpecified condition
A2 ± GroundConstantContinuity
A4 ± GroundConstantBattery positive voltage
A1 ± GroundIgnition switch LOCKNo voltage
A1 ± GroundIgnition switch ACC or ONBattery positive voltage
If the circuit is not as specified, inspect the circuits connected
to other parts.
HINT:
Check the wire harness between radio receiver assembly and
the CD auto changer, between radio receiver assembly and
power amplifier.

I04188
Wire Harness Side
± BODY ELECTRICALAUDIO SYSTEM
BE±219
2520 Author: Date:
2000 LEXUS GS300/GS400 (RM718U)
4. NAKAMICHI made:
INSPECT CD AUTO CHANGER CIRCUIT
Disconnect connectors from CD auto changer and inspect the
connector on the wire harness side.
Tester connectionConditionSpecified condition
14 ± GroundConstantContinuity
4 ± GroundIgnition switch LOCKNo voltage
4 ± GroundIgnition switch ACC or ONBattery positive voltage
5 ± GroundConstantBattery positive voltage
If the circuit is not as specified, inspect the circuits connected
to other parts.
HINT:

Check the wire harness between the radio receiver as-
sembly and the CD auto changer.

Since the signals to and from the MUTE, R±, R+, L±, L+,
TX
± and TX+ terminals are serial signals, they cannot or-
dinarily be measured with a tester.

I04309
Wire Harness Side
Connector ºBº
Connector ºDº Connector ºCº Connector ºAº BE±220
± BODY ELECTRICALAUDIO SYSTEM
2521 Author: Date:
2000 LEXUS GS300/GS400 (RM718U)
5. NAKAMICHI made:
INSPECT POWER AMPLIFIER CIRCUIT
Disconnect the connector from power amplifier and inspect the
connector on the wire harness side.
Tester connectionConditionSpecified condition
A1 ± Ground
A4 ± Ground
D1 ± Ground
ConstantContinuity
A6 ± GroundIgnition switch LOCK and radio switch ONNo voltage
A6 ± GroundIgnition switch ACC or ON and radio switch ONBattery positive voltage
A2 ± GroundConstantBattery positive voltage
A5 ± GroundConstantBattery positive voltage
If the circuit is not as specified, inspect the circuits connected
to other parts.

I04189
Wire Harness Side
Connector ºBº
Connector ºDº Connector ºCº Connector ºAº
± BODY ELECTRICALAUDIO SYSTEM
BE±221
2522 Author: Date:
2000 LEXUS GS300/GS400 (RM718U)
6. NAKAMICHI made:
INSPECT RADIO RECEIVER ASSEMBLY CIRCUIT
Disconnect the connectors from the radio receiver assembly,
and inspect the connector on the wire harness side.
Tester connectionConditionSpecified condition
D3 ± GroundConstantContinuity
D4 ± GroundConstantBattery positive voltage
D1 ± GroundIgnition switch LOCKNo voltage
D1 ± GroundIgnition switch ACC or ONBattery positive voltage
*: w/ LEXUS navigation system
If the circuit is not as specified, inspect the circuits connected
to other parts.
HINT:
Check the wire harness between radio receiver assembly and
the CD auto changer, between radio receiver assembly and
power amplifier.
7. INSPECT GLASS IMPRINTED ANTENNA
(Use same procedure as for ºINSPECT DEFOGGER WIRESº
on page BE±108.)
8. REPAIR GLASS IMPRINTED ANTENNA
(Use same procedure as for ºREPAIR DEFOGGER WIRESº on
page BE±108.)

BE±226
± BODY ELECTRICALANTENNA
2527 Author: Date:
2000 LEXUS GS300/GS400 (RM718U)6 ± Ground
Ignition switch ACC or LOCKNo voltage
6 ± GroundIgnition switch ONBattery positive voltage
8 ± GroundIgnition switch LOCKNo voltage
8 ± GroundIgnition switch ACC or ONBattery positive voltage
If circuit is as specified, replace the relay.

BE0G0±05
1
CLOCK WILL NOT OPERATEPASSENGER SEAT BELT WARNING LIGHT DOES NOT OPERATE
I04264
Wire Harness Side5
4
3
6
1RAD NO.2 Fuse
DOME Fuse
Combination
Meter
Body ECU
No.2
Ground ACC
+B
PBEW
ILL
E Clock Assembly
± BODY ELECTRICALCLOCK
BE±227
2528 Author: Date:
2000 LEXUS GS300/GS400 (RM718U)
CLOCK
TROUBLESHOOTING
HINT:
Troubleshoot the clock according to the table below.
TroubleshootingNo.
Passenger seat belt warning light does not light up.1
Clock will not operate1
Clock loses or gains time2
± 1.5 seconds / day
INSPECT CLOCK CIRCUIT
(See page DI±849)
TROUBLESHOOTING NO.1
(a) Check that the battery positive voltage is 10 ± 16 V.
If voltage is not as specified, replace the battery.
(b) Check that the DOME and RAD NO.2 fuses are not
blown.
If the fuse is blown, replace the fuse and check for short.
(c) Troubleshoot the clock as follows.
HINT:
Inspect the connector on the wire harness side.

Ye s
Ye sNo
No
Is there battery positive voltage between terminal +B and
body ground?
Is there battery positive voltage between terminal ACC and
body ground?
Replace clock.+B wire harness faulty.
Ye sNo
Is there continuity between terminal GND and
body ground?Ground wire harnss faulty. ACC wire harness faulty.
2 CLOCK LOSES OR GAINS TIME
I04264
Wire Harness Side5
4
3
6
1RAD NO.2 Fuse
DOME Fuse
Combination
Meter
Body ECU
No.2
Ground ACC
+B
PBEW
ILL
E Clock Assembly
Ye s
Is there battery positive voltage between terminal +B and
body ground?
Adjust or replace clock.Bellow 10 V
Locate cause and repair, or recharge battery.
Ye s
Is there battery positive voltage between terminal ACC and
body ground?Bellow 10 V
Locate cause and repair, or recharge battery.
BE±228
± BODY ELECTRICALCLOCK
2529 Author: Date:
2000 LEXUS GS300/GS400 (RM718U)
TROUBLESHOOTING NO.2
(a) Check that the battery positive voltage is 10 ± 16 V.
If voltage is not as specified, replace the battery.
(b) Inspect the error of the clock.
Allowable error (per day): ± 1.5 seconds
If the error exceeds the allowable error, replace the clock.
(c) Check that the clock adjusting button is sticking in posi-
tion and has failed to return.
If the error exceeds the allowable error, replace the clock.
(d) Troubleshoot the clock as follows.
HINT:
Inspect the connector on the wire harness side.

BE0G1±08
I01374
Ignitioin SwitchClock Assembly
Driver Side Junction Block

SRS ACC Fuse
Passenger Side
Junction Block

DOME Fuse
± BODY ELECTRICALCLOCK
BE±229
2530 Author: Date:
2000 LEXUS GS300/GS400 (RM718U)
LOCATION