lock LEXUS GS400 2000 Service Repair Manual

I04072
4 3
I04073
54
I04074
1
54 2
I04076
Wire Harness Side BE±78
± BODY ELECTRICALWIPER AND WASHER SYSTEM
2379 Author: Date:
2000 LEXUS GS300/GS400 (RM718U)
4. INSPECT WIPER MOTOR OPERATION
High speed:
Connect the positive (+) lead from the battery to terminal 3 and
the negative (±) lead to terminal 4, check that the motor oper-
ates at high speed.
If operation is not as specified, replace the motor.
5. INSPECT WIPER MOTOR OPERATION
Stopping at stop position:
(a) Operate the motor at low speed and stop the motor opera-
tion anywhere except at the stop position by disconnect-
ing positive (+) lead from terminal 5.
(b) Connect terminals 1 and 5.
(c) Connect the positive (+) lead from the battery to terminal
2 and negative (±) lead to terminal 4, check that the motor
stops running at the stop position after the motor operates
again.
If operation is not as specified, replace the motor.
6. INSPECT WIPER MOTOR CIRCUIT
Connector disconnected:
Disconnect the connector from the motor and inspect the con-
nector on the wire harness side, as shown.
Tester connectionConditionSpecified condition
4 ± GroundConstantContinuity
2 ± GroundIgnition switch LOCK or ACCNo voltage
2 ± GroundIgnition switch ONBattery positive voltage
If circuit is not as specified, inspect the circuits connected to oth-
er parts.

BE0HH±07
I01359
Brake Master Cylinder

Brake Fluid Level
Warning Switch
Combination Meter
and Telltale Light
Assembly
Airbag Sensor Assembly Parking Brake Switch
Driver Side
Junction Block

GAUGE Fuse

SRS±B FuseIgnition Switch
ECM
Washer Tank

Washer Level
Warning Switch Engine Room No.1
Junction Block

MPX±B Fuse
Seat Belt Buckle Switch
Rheostat Light Control
ABS, TRAC and VSC ECU
Clock Assembly

Passenger Seat Belt
Waning Light
BE±80
± BODY ELECTRICALCOMBINATION METER
2381 Author: Date:
2000 LEXUS GS300/GS400 (RM718U)
COMBINATION METER
LOCATION
The vehicle shown in this illustration is ºGS400º.
All components of ºGS300º other than the ones used for engine are same as ºGS400º.

I04250

Combination Meter Wiring Circuit ± 1
:Speedometer
:Tachometer
:Fuel Receiver Gauge
:Engine Coolant
Temperature
Receiver Gauge
Speed Control Unit
CLOCK
to GAUGE Fuse
to MPX±B Fuse
to SRS Fuse
Tilt and Telescopic ECU
Body ECU NO.2ECM (GS400)
Ignitor (GS300)
Fuel Main Sender GaugeGround
Fuel Sub Sender Gauge
Light Control Rheostat
Illuminations
ABS, TRAC and VSC ECU
ABS, TRAC and VSC ECU Speed Signal Passenger seat
belt warning
Rr LIGHTS
SEAT BELT
OIL PRESS
OIL LEVEL
DOOR IG+
SRS +BA/T P
A/T R
A/T N
A/T D
A/T 4
A/T 3
A/T 2
A/T L
CRUISE MPX+BIG+IG+
5V
+B
to ECUto
PANEL
Fuse B4
B5
B6
B9
A5
A17A3A8 B16
LCDECU S
T
F
E
Power Source
Brake
Buzzer A11A2 A1 A6
B1
B13
B14A4
B22 ECU
ECU
ECU
S
T
F
E
CHARGE
FUEL LVL
ECT PWR
ECT SNOW TAIL or HEAD
Ground IG+IG+ IG+ IG+
+B
± BODY ELECTRICALCOMBINATION METER
BE±83
2384 Author: Date:
2000 LEXUS GS300/GS400 (RM718U)

Clock (Passenger seat belt warning light)
Tilt and telescopic ECU
Fuel main sender gauge
Fuel sub sender gauge
ABS, TRAC and VSC ECU (Speed signal)
Speed control unit
Headlight dimmer switch
Ground
Window washer level warning switch
Body control No.2 ECU
ECM
ABS, TRAC and VSC ECU (VSC warning light)
ABS, TRAC and VSC ECU (SLIP warning light)
ABS, TRAC and VSC ECU (TRAC OFF warning light)
ABS, TRAC and VSC ECU (ABS warning light)
ABS, TRAC and VSC ECU (Brake warning light)
GAUGE fuse
Turn signal flasher (Left turn side)
Turn signal flasher (Right turn side)
Light control rheostat (+B)
Light control rheostat (Signal)
Light control rheostat (Ground)
PANEL fuse
Airbag sensor assembly
MPX+B fuse
DOME+B fuse
HEAD±RH fuse
Igniter
Headlight beam leveling control ECU
Ground
Telltale light assembly (IG+)
Telltale light assembly (ODO/TRIP switch)
Telltale light assembly (Right turn signal)
Telltale light assembly (RESET switch)
Telltale light assembly (Left turn signal)
GroundWiring connector side No.1
1
1
2
3
4
5
6
7
8
10
11
12
13
14
15
16
17
1 1
1
2
3
4
5
6
9
12
13
14
15
16
18
22
1 1
1
3
4
8
9
10 U B A
± BODY ELECTRICALCOMBINATION METER
BE±85
2386 Author: Date:
2000 LEXUS GS300/GS400 (RM718U)

I04097
Battery Ignition
SwitchWarning Light
Wire Harness Side
I04098
Wire Harness Side
I04099
BatteryIgnition
SwitchWarning Light
Wire Harness Side BE±100
± BODY ELECTRICALCOMBINATION METER
2401 Author: Date:
2000 LEXUS GS300/GS400 (RM718U)
23. INSPECT REAR LIGHTS WARNING LIGHT
(See page DI±841)
(a) Disconnect the connector from the light failure sensor and
ground terminal 3 on the wire harness side connector.
(b) Start the engine, check that the warning light lights up.
If the warning light does not light up, inspect the bulb or wire har-
ness.
24. INSPECT LIGHT FAILURE SENSOR CIRCUIT
Disconnect connector from the light failure sensor and inspect
the connectors on the wire harness side as follows.
Tester connectionConditionSpecified condition
1 ± GroundConstantContinuity *
2 ± GroundConstantContinuity *
6 ± GroundConstantContinuity *
7 ± GroundConstantContinuity *
11 ± GroundConstantContinuity
12 ± GroundConstantContinuity *
5 ± GroundLight control switch OFFNo voltage
5 ± GroundLight control switch in TAIL or HEADBattery positive voltage
8 ± GroundIgnition switch in LOCK or ACCNo voltage
8 ± GroundIgnition switch ONBattery positive voltage
9, 10 ± GroundStop light switch OFFNo voltage
9, 10 ± GroundStop light switch ONBattery positive voltage
*: There is resistance because this circuit is grounded through
the bulb.
If circuit is as specified, replace the relay.
If circuit is not as specified, wiring diagram and inspect the cir-
cuits connected to other parts.
25. INSPECT ENGINE OIL LEVEL WARNING LIGHT
(a) Disconnect the connector from the switch.
(b) Run the engine.
(c) Turn the ignition switch ON, check that the warning light
lights up approximatery 40 seconds later.
If the warning light does not light up, inspect bulb or wire har-
ness.

I04105
Dark
(10k W)Bright
(0W)
4
5
I01322
Battery Ignition
SwitchWarning Light
2 1 Wire Harness Side
I01323
1 2 OFF
ON
I01328
Battery Ignition
SwitchWarning Light
2 1 Wire Harness Side
I04107
12
4
OFF
ON BE±102
± BODY ELECTRICALCOMBINATION METER
2403 Author: Date:
2000 LEXUS GS300/GS400 (RM718U)
30. INSPECT LIGHT CONTROL RHEOSTAT OPERATION
Gradually, turn the rheostat knob from the bright side to dark
side and check that the resistance decreases from 10 kW to 0
W between terminal 4 and 5. (Rheostat knob turned to clock-
wise)
If operation is not as specified, replace the rheostat light control.
31. INSPECT WINDOW WASHER LEVEL WARNING
LIGHT
(a) Disconnect the connector from the warning switch and
ground terminal on the wire harness side connector.
(b) Engine running and check that the warning light lights up.
If the warning light does not light up, inspect the bulb or wire har-
ness.
32. INSPECT WINDOW WASHER LEVEL WARNING
SWITCH CONTINUITY
(a) Check that no continuity exists between the terminals with
the switch OFF (float up).
(b) Check that continuity exists between the terminals with
the switch ON (float down).
If operation is not as specified, replace the switch or inspect
ground point.
33. INSPECT SEAT BELT WARNING LIGHT
(a) Disconnect the connector from the retractor switch and
ground terminal on the wire harness side connector.
(b) Turn the ignition switch ON and check that the warning
light lights up.
If the warning light does not light up, inspect the bulb or wire har-
ness.
34. INSPECT SEAT BELT BUCKLE SWITCH CONTINUITY
(a) Check that continuity exists between the terminals 1 and
4 on the switch side connector with the switch ON (belt
fastened).
(b) Check that continuity exists between the terminals 2 and
4 on the switch side connector with the switch OFF (belt
unfastened).
If operation is not as specified, replace the switch.

F01619
BR0JD±03
F01620
Adjusting Nut
Lock Nut
± BRAKEPARKING BRAKE PEDAL
BR±11
2119 Author: Date:
2000 LEXUS GS300/GS400 (RM718U)
PARKING BRAKE PEDAL
ON±VEHICLE INSPECTION
1. CHECK PARKING BRAKE PEDAL TRAVEL
Depress the parking brake pedal all the way and count the num-
ber of clicks.
Parking brake lever travel at 294 N (30 kgf, 66.1 Ibf):
7 ± 9 clicks
2. IF NECESSARY, ADJUST PARKING BRAKE
HINT:
Before adjusting the parking brake, make sure that the rear
brake shoe clearance has been adjusted. For shoe clearance
adjustment see page BR±37.
(a) Loosen the lock nut and turn the adjusting nut until the
pedal travel is correct.
(b) Tighten the lock nut.
Torque: 5.4 N´m (55 kgf´cm, 48 in.´lbf)

BR0JE±03
F07241
No. 1 Safety Pad
No. 1 Under Cover
Front Door Scuff Plate End Pad
Parking Brake Switch
Parking Brake Pedal
AssemblyParking Brake WireAdjusting NutLock Nut
13 (130, 9)
5.4 (55, 48 in.´lbf)
No. 7 Heater to Register Duct
N´m (kgf´cm, ft´lbf) : Specified torque BR±12
± BRAKEPARKING BRAKE PEDAL
2120 Author: Date:
2000 LEXUS GS300/GS400 (RM718U)
COMPONENTS

BR0JF±03
± BRAKEPARKING BRAKE PEDAL
BR±13
2121 Author: Date:
2000 LEXUS GS300/GS400 (RM718U)
REMOVAL
1. REMOVE FRONT DOOR SCUFF PLATE, END PAD, NO. 1 UNDER COVER, NO. 1 SAFETY PAD
AND NO. 7 HEATER TO REGISTER DUCT (See page BO±88)
2. REMOVE PARKING BRAKE PEDAL ASSEMBLY
(a) Disconnect the parking brake switch connector.
(b) Remove the 2 bolts, and disconnect the parking brake release lever from the safety pad.
Torque: 5.4 N´m (55 kgf´cm, 48 in.´lbf)
(c) Remove the lock nut and the adjusting nut from the parking brake wire.
(d) Remove the parking brake wire.
(e) Remove the 2 bolts, 2 nuts and parking brake pedal assembly.
Torque: 13 N´m (130 kgf´cm, 9 ft´lbf)
3. REMOVE PARKING BRAKE SWITCH
Remove the screw and parking brake switch from the parking brake pedal assembly.

BR0JK±03
F01624
± BRAKEFRONT BRAKE CALIPER
BR±19
2127 Author: Date:
2000 LEXUS GS300/GS400 (RM718U)
REMOVAL
1. DISCONNECT FLEXIBLE HOSE
Remove the union bolt and 2 gaskets from the caliper, then dis-
connect the flexible hose from the caliper. Use a container to
catch brake fluid as it drains out.
Torque: 30 N´m (310 kgf´cm, 22 ft´lbf)
HINT:
At the time of installation, install the flexible hose lock securely
in the lock hole in the caliper.
2. REMOVE CALIPER
(a) Hold the sliding pin and loosen the 2 installation bolts.
Torque: 34 N´m (350 kgf´cm, 25 ft´lbf)
(b) Remove the 2 installation bolts.
(c) Remove the caliper from the torque plate.
3. REMOVE 2 ANTI±SQUEAL SPRINGS
4. REMOVE 2 BRAKE PADS WITH 4 ANTI±SQUEAL
SHIMS
5. REMOVE 4 PAD SUPPORT PLATES