fog light LEXUS GS400 2000 Service User Guide

CH043±01
B01372
Except Maintenance±Free Battery
B01888
Maintenance±Free BatteryVoltmeter
± CHARGING (2JZ±GE)CHARGING SYSTEM
CH±1
1603 Author: Date:
2000 LEXUS GS300/GS400 (RM718U)
CHARGING SYSTEM
ON±VEHICLE INSPECTION
CAUTION:

Check that the battery cables are connected to the
correct terminals.

Disconnect the battery cables when the battery is giv-
en a quick charge.

Do not do tests with a high voltage insulation resis-
tance tester.

Never disconnect the battery while the engine is run-
ning.
1. CHECK BATTERY ELECTROLYTE LEVEL
Check the electrolyte quantity of each cell.
Maintenance±Free Battery:
If under the lower level, replace the battery (or add distilled wa-
ter if possible). Check the charging system.
Except Maintenance±Free Battery:
If under the lower level, add distilled water.
2. Except Maintenance±Free Battery:
CHECK BATTERY SPECIFIC GRAVITY
Check the specific gravity of each cell.
Standard specific gravity: 1.25 ± 1.29 at 20°C (68°F)
If the specific gravity is less than specification, charge the bat-
tery.
3. Maintenance±Free Battery:
CHECK BATTERY POSITIVE VOLTAGE
(a) After having driven the vehicle and in the case that 20
minutes have not passed after having stopped the en-
gine, turn the ignition switch ON and turn on the electrical
system (headlight, blower motor, rear defogger etc.) for
60 seconds to remove the surface charge.
(b) Turn the ignition switch OFF and turn off the electrical sys-
tems.
(c) Measure the battery positive voltage between the nega-
tive (±) and positive (+) terminals of the battery.
Standard voltage: 12.5 ± 12.9 V at 20°C (68°F)
If the voltage is less than specification, charge the battery.
4. CHECK BATTERY TERMINALS AND FUSES
(a) Check that the battery terminals are not loose or cor-
roded.
If the terminals are corroded, clean the terminals.
(b) Check the fusible link and fuses for continuity.

B02389
B02390
HEAT METHOD: When the problem seems to occur when the suspect area is heated. 2
NOTICE:3 WATER SPRINKLING METHOD:
(1)
(2)
4 OTHER: When a malfunction seems to occur when electrical load is excessive.When the malfunction seems to occur on a rainy day or in a
high±humidity condition. Heat the component that is the likely cause of the malfunction
with a hair dryer or similar object. Check to see if the malfunction
occurs.
Sprinkle water onto the vehicle and check to see if the malfunc-
tion occurs.
Turn on all electrical loads including the heater blower, head
lights, rear window defogger, etc. and check to see if the mal-
function occurs.ON HINT:
If a vehicle is subject to water leakage, the leaked water may
contaminate the ECU. When testing a vehicle with a water leak-
age problem, special caution must be taken.
Malfunc-
tion
Do not heat to more than 60 °C (140 °F). (Temperature
is limited not to damage the components.)
Do not apply heat directly to parts in the ECU. (1)
(2)
Never sprinkle water directly into the engine compart-
ment, but indirectly change the temperature and hu-
midity by applying water spray onto the radiator front
surface.
Never apply water directly onto the electronic compo-
nents. NOTICE: IN±26
± INTRODUCTIONHOW TO TROUBLESHOOT ECU CONTROLLED
SYSTEMS
26 Author: Date:
2000 LEXUS GS300/GS400 (RM718U)

PP0O2±02
± PREPARATIONBODY ELECTRICAL
PP±93
145 Author: Date:
2000 LEXUS GS300/GS400 (RM718U)
EQUIPMENT
Voltmeter
Ammeter
Ohmmeter
Test lead
ThermometerEngine coolant temperature sender gauge, Engine oil level warn-
ing switch, Seat heater
SyphonBrake fluid level warning switch
Oil bathEngine oil level warning switch
Bulb (1.4 W)Defogger switch
Bulb (3.4 W)Fuel sender gauge, Engine coolant temperature receiver gauge,
Seat belt warning relay
Dry cell batteryFuel sender gauge, Power mirror
Heat lightSeat heater
Hexagon wrench (6 mm)Power seat
Torque wrench
Clip removerFor removing cowl louver
Masking tapeRear window defogger wire
Tin foilRear window defogger wire