LEXUS GS400 2000 Service Repair Manual

BE0GO±04
I04149
± BODY ELECTRICALWIRELESS DOOR LOCK CONTROL SYSTEM
BE±157
2458 Author: Date:
2000 LEXUS GS300/GS400 (RM718U)
INSPECTION
1. INSPECT WIRELESS DOOR LOCK TRANSMITTER
OPERATION
HINT:
Refer to ºWireless door lock control transmitter battery replace-
mentº on page BE±161.
(a) Using a screwdriver, remove the screw and cover.
(b) Remove the battery (lithium battery).
(c) Install a new or normal battery (lithium battery).
HINT:
When a new or normal battery can not be obtained, connect 2
new 1.5 V batteries in series, connect the battery (+) to the bat-
tery receptacle side terminal and battery (±) to the bottom termi-
nal, then apply 3 V voltage to the transmitter.
(d) In the location where is approx. 1 M away from driver's
outside handle in the right direction, face the key plate of
the transmitter to the vehicle, and check the transmitter
operation when pressing transmission switch on the side
of the transmitter body.
Standard:

Remote control of vehicle door lock can be operated.

LED lights up more than once.
HINT:

The minimum operation distance differs according to op-
erator, the way of holding the transmitter, and location.

As weak wave is used, operation distance might be short-
ened when noise is detected in strong wave or used fre-
quency.
(e) Install the battery (lithium battery).
(f) Install a cover so that O±ring is not distorted or slipped off.
(g) Using a screwdriver, tighten the screw.

I04150
I04151
BE±158
± BODY ELECTRICALWIRELESS DOOR LOCK CONTROL SYSTEM
2459 Author: Date:
2000 LEXUS GS300/GS400 (RM718U)
2. CHECK BATTERY CAPACITY
HINT:

Make sure to use the TOYOTA electrical tester.

With the battery unloaded, judge can not be made wheth-
er the battery is available or not on the test.

When the transmitter is faulty, the energy amount left in
the battery might not be checked correctly.

On the lithium battery used for the transmitter, the voltage
more than 2.5 V with the battery unloaded is shown on the
tester until the energy is completely consumed.
Accordingly when inspecting the energy amount left in the
battery, it is necessary to measure the voltage when the
battery is loaded. (1.2 kW).
(a) Remove the screws and cover using a (±) driver.
(b) Remove the battery (lithium battery) from the transmitter.
(c) Connect the lead to the (±) terminal of the transmitter and
install the battery.
(d) Connect the (+) tester to the (+) battery (lithium battery),
and (±) tester to the lead respectively.
(e) Press one of the transmitting switches on the transmitter
for approx. 1 second.
(f) Press the transmitting switch on the transmitter again to
check the voltage.
Standard: 2.1 V or more

N13471
1 2
I04152
Wire Harness Side
± BODY ELECTRICALWIRELESS DOOR LOCK CONTROL SYSTEM
BE±159
2460 Author: Date:
2000 LEXUS GS300/GS400 (RM718U)
HINT:

When the temperature of the battery is low, the judge can
not be made correctly.
When the outcome of the test is less than 2.1 V, conduct
the test again after leaving the battery in the place at 18
°C for more than 30 minutes.

By auto power off function, the voltage becomes no load
voltage (more than 2.5 V) condition 0.8 seconds after the
switch was pressed.
Make sure to read the voltage before of it.

High voltage might be shown 1 to 2 times after leaving the
battery, judge should be made with the voltage shown at
the 3rd time or later.
(g) Disconnect the lead.
(h) Set the battery (lithium battery) in the transmitter.
(i) Install the cover, so that the O±ring is not distorted or
slipped off.
(j) Using a screwdriver, tighten the screws.
3. INSPECT WIRELESS DOOR LOCK BUZZER OPERA-
TION
Connect the positive (+) lead from the ohmmeter to terminal 1
and the negative (±) lead to terminal 2, and measure resistance
of approx. 1 kW.
If resistance is not as specified, replace the buzzer.
4. INSPECT WIRELESS DOOR LOCK BUZZER CIRCUIT
(See page DI±800)
5. INSPECT WIRELESS DOOR LOCK CONTROL RE-
CEIVER CIRCUIT
(See page DI±788)
Connector disconnected:
Disconnect the connector from the receiver and inspect the
connector on the wire harness side, as shown.
Tester connectionConditionSpecified condition
1 ± GroundConstantContinuity
7 ± GroundConstantBattery positive voltage
If the circuit is not as specified, inspect the circuits connected
to other parts.

I04153
From Back Side BE±160
± BODY ELECTRICALWIRELESS DOOR LOCK CONTROL SYSTEM
2461 Author: Date:
2000 LEXUS GS300/GS400 (RM718U)
6. INSPECT WIRELESS DOOR LOCK CONTROL RE-
CEIVER CIRCUIT
Connector connected:
Connect the wire harness side connector to the receiver and in-
spect the wire harness side connector from the back side, as
shown.
Tester connectionConditionSpecified condition
3 ± Ground
Ignition switch position OFF
Key removed
Transmitter OFF " ON
4.5 ± 5.5 V " below 1 V
3 ± Ground
Ignition switch position OFF
Key removed
Transmitter OFF " ON
4.5 ± 5.5 V " below 1 V
4 ± Ground
Ignition switch position OFF
Key removed
Transmitter ON
10 ±14 V
If circuit is as specified, replace the receiver.
If the circuit is not as specified, inspect the circuits connected
to other parts.

BE0H5±06
I01348
Engine Room No.1
Junction BlockEngine Room No.2
Relay Block
Driver Side Junction BlockEngine Room No.3
Relay Block
Passenger Side Junction Block
BE±16
± BODY ELECTRICALPOWER SOURCE
2317 Author: Date:
2000 LEXUS GS300/GS400 (RM718U)
POWER SOURCE
LOCATION
The vehicle shown in this illustration is ºGS400º.
All components of ºGS300º other than the ones used for engine are same as ºGS400º.

I04026

Engine Room No.1 Junction Block
Fuses Relays
1. MAIN H±Fuse
2. FL ABS NO.1 H±Fuse
3. ALT H±Fuse
4. ABS NO.2 H±Fuse
5. H±LP CLN H±Fuse
6. RAD NO.1 Fuse
7. ALT±S Fuse
8. EFI Fuse
9. TURN HAZ Fuse
10. TEL Fuse
11. AM2 Fuse
13. HORN Fuse 12. ETCS Fuse
14. MPX±B Fuse
15. ECU±B1 Fuse
16. HTR FuseB. Starter Relay A. Headlight Control Relay
C. EFI Relay
17. FAN MAIN H±Fuse
18. CDS FAN H±Fuse
20. H±LP R LWR Fuse 19. RAD FAN H±Fuse
21. H±LP L LWR Fuse
22. H±LP R UPR Fuse
23. H±LP L UPR Fuse1
2 3 4 5 6 7 8 9 10 11 12 13
14 15
16 18 17 19
20 21 22 23 A
BC
± BODY ELECTRICALPOWER SOURCE
BE±17
2318 Author: Date:
2000 LEXUS GS300/GS400 (RM718U)

I04028

Engine Room No.3 Relay Block
Relays
A. FAN NO.1 Relay
B. FAN NO.2 Relay
C. A/C COMP Relay
D. FAN NO.3 Relay

Engine Room No.2 Relay Block
Relays
A. Horn Relay
B. ABS SOL Relay
C. TRC MTR Relay
D. ABS MTR Relay
I04027
I04028
A
B
C
D
EE. Headlight Dimmer
(Daytime Running Light No.2) Relay
A
B
C
DFuses
1. H±LP R UPR Fuse
(w/ Daytime Running Light System)
2 H±LP L UPR Fuse
(w/ Daytime Running Light System) 12 BE±18
± BODY ELECTRICALPOWER SOURCE
2319 Author: Date:
2000 LEXUS GS300/GS400 (RM718U)

I04029
Fuses
Relays 1. AM1 H±Fuse
2. WASHER Fuse
3. FOG Fuse
4. TAIL Fuse
B. Taillight Control Relay A. Fog Light Relay
C. Body ECU No.2
Driver Side Instrument Panel Junction Block
5. SRS±ACC Fuse
6. GAUGE Fuse
7. FUEL OPN Fuse
8. D FR DOOR Fuse
9. PANEL Fuse
10. HTR Fuse
11. SRS±B Fuse
12. P/SEAT (D) Fuse
13. RAD NO.2 Fuse
14. WIP Fuse
15. OBD Fuse
16. STOP Fuse
17. CIG Fuse
18. ECU±IG Fuse
19. STARTER Fuse
20. IGN Fuse
21. D FR DOOR Fuse
2
21 34 5
678 9
10 11 12 13
14 15 16 17
18 19 20AB
C 1
± BODY ELECTRICALPOWER SOURCE
BE±19
2320 Author: Date:
2000 LEXUS GS300/GS400 (RM718U)

I04030
Fuses
Relays 1. DEF H±Fuse
2. ±
3. ±
4. MIR HTR Fuse
A. Ignition Main Relay
B. Mirror Heater Relay
E. Body ECU No.1
Passenger Side Instrument Panel Junction Block
5. ±
6. ±
7. S/ROOF Fuse
8. P FR DOOR Fuse
9. ±
10. ±
11 .
12. P/SEAT (P) Fuse
13. DOME Fuse
14. SEAT HTR Fuse
15. ±
16. TV Fuse
17. ECU±B2 Fuse
18. ±
19. ±
20. ±
21. P FR DOOR Fuse
2
21 34 5
67 8 9
10 11 12 13
14 15 16 17
18 19 20AB
E
C. Defogger Relay
D. Heater Relay
CD
1
BE±20
± BODY ELECTRICALPOWER SOURCE
2321 Author: Date:
2000 LEXUS GS300/GS400 (RM718U)

BE0GP±09
I04154
I04155
I04156
Terminal
± BODY ELECTRICALWIRELESS DOOR LOCK CONTROL SYSTEM
BE±161
2462 Author: Date:
2000 LEXUS GS300/GS400 (RM718U)
REPLACEMENT
1. REPLACE TRANSMITTER (LITHIUM) BATTERY
NOTICE:
Special caution should be taken for handling each compo-
nent as they are precision electronic components.
(a) Using a screwdriver, remove the screw and cover.
NOTICE:
Do not pry out the cover forcibly.
HINT:
Push the cover with a finger as shown in the illustration, so that
there becomes clearance, then pry out the cover from that
clearance.
(b) Remove the transmitter.
(c) Using a screwdriver, remove the 2 screws and cover.
(d) Remove the battery (lithium battery).
NOTICE:
Do not push the terminals with a finger.
If prying up the battery (lithium battery) forcibly to re-
move, the terminals are deformed.
(e) Install a battery (lithium battery) as shown in the illustra-
tion.
NOTICE:
Face the battery upward. Take care not to deform the termi-
nals.
(f) Check that O±ring is not distorted or slipped off, and
install the cover.
(g) Using a screwdriver, tighten the 2 screws.
NOTICE:
When the shrews are tightened loosely, it might cause
faulty contact of battery (lithium battery) and terminals.
(h) Assemble the transmitter to the key plate and the cover.
(i) Using a screwdriver, tighten the screw.