battery LEXUS GS400 2000 Service Manual PDF

I05029
1 23 4 5
6 78 9 10
± BODY ELECTRICALPOWER SOURCE
BE±29
2330 Author: Date:
2000 LEXUS GS300/GS400 (RM718U)
6. INSPECT PASSENGER COWL SIDE RELAY BLOCK
CIRCUIT
Remove the relay from the relay block and inspect the connec-
tor on relay block side.
Relay Tester connectionConditionSpecified condition
DEF 1 ± GroundConstantBattery positive voltage
HEATER 6 ± GroundConstantBattery positive voltage
If the circuit is not as specified, inspect the circuits connected
to other parts.

BE0GE±03
I04310
Wire Harness Side
I04189
Wire Harness Side
Connector ºBº
Connector ºDº Connector ºCº Connector ºAº
± BODY ELECTRICALAUDIO SYSTEM
BE±217
2518 Author: Date:
2000 LEXUS GS300/GS400 (RM718U)
INSPECTION
1. Except NAKAMICHI made:
INSPECT CD AUTO CHANGER CIRCUIT
Disconnect connectors from CD auto changer and inspect the
connector on the wire harness side.
Tester connectionConditionSpecified condition
8 ± GroundConstantContinuity
5 ± GroundConstantBattery positive voltage
10 ± GroundIgnition switch LOCKNo voltage
10 ± GroundIgnition switch ACC or ONBattery positive voltage
If the circuit is not as specified, inspect the circuits connected
to other parts.
HINT:

Check the wire harness between the radio receiver as-
sembly and the CD auto changer.

Since the signals to and from the MUTE, R±, R+, L±, L+,
TX
± and TX+ terminals are serial signals, they cannot or-
dinarily be measured with a tester.
2. Except NAKAMICHI made:
INSPECT POWER AMPLIFIER CIRCUIT
Disconnect the connector from power amplifier and inspect the
connector on the wire harness side.
Tester connectionConditionSpecified condition
B7 ± GroundConstantContinuity
C12 ± GroundIgnition switch LOCK and radio switch ONNo voltage
C12 ± GroundIgnition switch ACC or ON and radio switch ONBattery positive voltage
B4 ± GroundConstantBattery positive voltage
If the circuit is not as specified, inspect the circuits connected
to other parts.

I04190
Wire Harness Side
Connector ºAº Connector ºBº BE±218
± BODY ELECTRICALAUDIO SYSTEM
2519 Author: Date:
2000 LEXUS GS300/GS400 (RM718U)
3. Except NAKAMICHI made:
INSPECT RADIO RECEIVER ASSEMBLY CIRCUIT
Disconnect the connectors from the radio receiver assembly,
and inspect the connector on the wire harness side.
Tester connectionConditionSpecified condition
A2 ± GroundConstantContinuity
A4 ± GroundConstantBattery positive voltage
A1 ± GroundIgnition switch LOCKNo voltage
A1 ± GroundIgnition switch ACC or ONBattery positive voltage
If the circuit is not as specified, inspect the circuits connected
to other parts.
HINT:
Check the wire harness between radio receiver assembly and
the CD auto changer, between radio receiver assembly and
power amplifier.

I04188
Wire Harness Side
± BODY ELECTRICALAUDIO SYSTEM
BE±219
2520 Author: Date:
2000 LEXUS GS300/GS400 (RM718U)
4. NAKAMICHI made:
INSPECT CD AUTO CHANGER CIRCUIT
Disconnect connectors from CD auto changer and inspect the
connector on the wire harness side.
Tester connectionConditionSpecified condition
14 ± GroundConstantContinuity
4 ± GroundIgnition switch LOCKNo voltage
4 ± GroundIgnition switch ACC or ONBattery positive voltage
5 ± GroundConstantBattery positive voltage
If the circuit is not as specified, inspect the circuits connected
to other parts.
HINT:

Check the wire harness between the radio receiver as-
sembly and the CD auto changer.

Since the signals to and from the MUTE, R±, R+, L±, L+,
TX
± and TX+ terminals are serial signals, they cannot or-
dinarily be measured with a tester.

I04309
Wire Harness Side
Connector ºBº
Connector ºDº Connector ºCº Connector ºAº BE±220
± BODY ELECTRICALAUDIO SYSTEM
2521 Author: Date:
2000 LEXUS GS300/GS400 (RM718U)
5. NAKAMICHI made:
INSPECT POWER AMPLIFIER CIRCUIT
Disconnect the connector from power amplifier and inspect the
connector on the wire harness side.
Tester connectionConditionSpecified condition
A1 ± Ground
A4 ± Ground
D1 ± Ground
ConstantContinuity
A6 ± GroundIgnition switch LOCK and radio switch ONNo voltage
A6 ± GroundIgnition switch ACC or ON and radio switch ONBattery positive voltage
A2 ± GroundConstantBattery positive voltage
A5 ± GroundConstantBattery positive voltage
If the circuit is not as specified, inspect the circuits connected
to other parts.

I04189
Wire Harness Side
Connector ºBº
Connector ºDº Connector ºCº Connector ºAº
± BODY ELECTRICALAUDIO SYSTEM
BE±221
2522 Author: Date:
2000 LEXUS GS300/GS400 (RM718U)
6. NAKAMICHI made:
INSPECT RADIO RECEIVER ASSEMBLY CIRCUIT
Disconnect the connectors from the radio receiver assembly,
and inspect the connector on the wire harness side.
Tester connectionConditionSpecified condition
D3 ± GroundConstantContinuity
D4 ± GroundConstantBattery positive voltage
D1 ± GroundIgnition switch LOCKNo voltage
D1 ± GroundIgnition switch ACC or ONBattery positive voltage
*: w/ LEXUS navigation system
If the circuit is not as specified, inspect the circuits connected
to other parts.
HINT:
Check the wire harness between radio receiver assembly and
the CD auto changer, between radio receiver assembly and
power amplifier.
7. INSPECT GLASS IMPRINTED ANTENNA
(Use same procedure as for ºINSPECT DEFOGGER WIRESº
on page BE±108.)
8. REPAIR GLASS IMPRINTED ANTENNA
(Use same procedure as for ºREPAIR DEFOGGER WIRESº on
page BE±108.)

BE0N6±04
I05587
2 5
I05580
2 5
Z08688
2 13
45 768 Wire Harness Side
± BODY ELECTRICALANTENNA
BE±225
2526 Author: Date:
2000 LEXUS GS300/GS400 (RM718U)
INSPECTION
1. Auto Antenna Models:
INSPECT ANTENNA MOTOR
(a) Connect the positive (+) lead from the battery to terminal
2 and the negative (±) lead to terminal 5.
(b) Check that the motor turns (moves upward).
NOTICE:
These tests must be done quickly (within 3 ± 5 seconds) to
prevent the coil from burning out.
(c) Then, reverse the polarity, check that the motor turns the
opposite way (moves downward).
NOTICE:
These tests must be done quickly (within 3 ± 5 seconds) to
prevent the coil from burning out.
2. Auto Antenna Models:
INSPECT ANTENNA MOTOR CONTROL RELAY CIR-
CUIT
Disconnect the connector from the relay and inspect the con-
nector on wire harness side, as shown in the chart below.
Tester connectionConditionSpecified condition
7 ± GroundConstantContinuity
1 ± GroundIgnition switch ACC or ON,
and radio switch ON and OthersNo voltage
1 ± GroundIgnition switch ACC or ON,
and radio switch ON and AMBattery positive voltage
2 ± GroundIgnition switch ACC or ON,
and radio or tape or CD switch OFFNo voltage
2 ± GroundIgnition switch ACC or ON,
and radio or tape or CD switch ONBattery positive voltage
3 ± GroundConstantBattery positive voltage
4 ± GroundIgnition switch ACC or ON,
and radio switch ON and OthersNo voltage
4 ± Ground
Ignition switch ACC or ON,
and radio switch ON and
AM or FM (87.9 ± 96.0 MHz)
Battery positive voltage
5 ± GroundIgnition switch ACC or ON,
and radio switch OFFNo voltage
5 ± GroundIgnition switch ACC or ON,
and radio switch ONBattery positive voltage

BE±226
± BODY ELECTRICALANTENNA
2527 Author: Date:
2000 LEXUS GS300/GS400 (RM718U)6 ± Ground
Ignition switch ACC or LOCKNo voltage
6 ± GroundIgnition switch ONBattery positive voltage
8 ± GroundIgnition switch LOCKNo voltage
8 ± GroundIgnition switch ACC or ONBattery positive voltage
If circuit is as specified, replace the relay.

BE0G0±05
1
CLOCK WILL NOT OPERATEPASSENGER SEAT BELT WARNING LIGHT DOES NOT OPERATE
I04264
Wire Harness Side5
4
3
6
1RAD NO.2 Fuse
DOME Fuse
Combination
Meter
Body ECU
No.2
Ground ACC
+B
PBEW
ILL
E Clock Assembly
± BODY ELECTRICALCLOCK
BE±227
2528 Author: Date:
2000 LEXUS GS300/GS400 (RM718U)
CLOCK
TROUBLESHOOTING
HINT:
Troubleshoot the clock according to the table below.
TroubleshootingNo.
Passenger seat belt warning light does not light up.1
Clock will not operate1
Clock loses or gains time2
± 1.5 seconds / day
INSPECT CLOCK CIRCUIT
(See page DI±849)
TROUBLESHOOTING NO.1
(a) Check that the battery positive voltage is 10 ± 16 V.
If voltage is not as specified, replace the battery.
(b) Check that the DOME and RAD NO.2 fuses are not
blown.
If the fuse is blown, replace the fuse and check for short.
(c) Troubleshoot the clock as follows.
HINT:
Inspect the connector on the wire harness side.

Ye s
Ye sNo
No
Is there battery positive voltage between terminal +B and
body ground?
Is there battery positive voltage between terminal ACC and
body ground?
Replace clock.+B wire harness faulty.
Ye sNo
Is there continuity between terminal GND and
body ground?Ground wire harnss faulty. ACC wire harness faulty.
2 CLOCK LOSES OR GAINS TIME
I04264
Wire Harness Side5
4
3
6
1RAD NO.2 Fuse
DOME Fuse
Combination
Meter
Body ECU
No.2
Ground ACC
+B
PBEW
ILL
E Clock Assembly
Ye s
Is there battery positive voltage between terminal +B and
body ground?
Adjust or replace clock.Bellow 10 V
Locate cause and repair, or recharge battery.
Ye s
Is there battery positive voltage between terminal ACC and
body ground?Bellow 10 V
Locate cause and repair, or recharge battery.
BE±228
± BODY ELECTRICALCLOCK
2529 Author: Date:
2000 LEXUS GS300/GS400 (RM718U)
TROUBLESHOOTING NO.2
(a) Check that the battery positive voltage is 10 ± 16 V.
If voltage is not as specified, replace the battery.
(b) Inspect the error of the clock.
Allowable error (per day): ± 1.5 seconds
If the error exceeds the allowable error, replace the clock.
(c) Check that the clock adjusting button is sticking in posi-
tion and has failed to return.
If the error exceeds the allowable error, replace the clock.
(d) Troubleshoot the clock as follows.
HINT:
Inspect the connector on the wire harness side.