display Lexus GS430 2006 Scheduled Maintenance Guide / LEXUS 2006 GS430/GS300 FROM JAN. 2005 PROD. (OM30649U) User Guide

SWITCHES
52
CAUTION
Be careful not to get your fingers caught between the
wipers and windshield.
When the wiper lever is in the “AUTO” position with the
engine switch on, the wipers could operate
automatically in the following cases:
 If you touch the upper center of the windshield
adjacent to the sensor.
 If you wipe the upper center of the windshield
(adjacent to which the sensor is located) with a towel.
 If the windshield vibrates.
 If you touch the sensor.
For mist wiper operations (a single wipe), pull the lever up
and release it.
To make the washer squirt, pull the lever toward you and
release it.
If the wiper lever is in the “OFF” position, the wipers will
automatically make 3 wipes and then a single wipe later to
sweep the windshield completely.* The interval between the
3 wipes and the last wipe will depend on the vehicle speed.
The last sweep does not happen if the vehicle speed exceeds
about 170 km/h (106 mph).
NOTE:
*This function can be changed as follows: The time before the last single wipe can be set for
about 3 seconds.
 The last single wipe can be deactivated.
Ask your Lexus dealer for details.
The warning message “LOW WASHER FLUID” is displayed in
the multi−information display when the fluid level in the tank
becomes very low. For information on adding washer fluid, see
“Adding washer fluid” on page 579.
When the headlights are on and the washers are activated by
pushing the windshield washer switch, the headlight cleaner
operates once automatically.
In cold weather, warm the windshield with the defroster before
using the washer. This will help prevent icing, which could
block your vision.
The rear window and outside rear view mirror defogger
automatically turns on when you operate the wipers.

SWITCHES
55
HEADLIGHT CLEANER SWITCH
The headlight cleaner switch is located in the switch box.
G12010
Push the button to use the switch box. To spray fluid on
the headlights, push the switch with the headlights on.
The engine switch must be selected in “IG−ON” mode.
The warning message “LOW WASHER FLUID” is displayed in
the multi−information display when the fluid level in the tank
becomes very low. For information on adding washer fluid, see
“Adding washer fluid” on page 579.
After operation, be sure to close the switch box to its original
position.
CAUTION
To reduce the chance of injury in case of an accident or
a sudden stop, keep the switch box closed when not in
use while driving.
NOTICE
Do not turn the headlight cleaner on with the washer
fluid tank empty. It may cause the cleaner motor to
overheat.

SECTION 1 – 3
67
INSTRUMENTS AND CONTROLS
Gauges, meters and service reminder
indicators
Fuel gauge68
. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .\
. . . . . . . . . .
Engine coolant temperature gauge 68
. . . . . . . . . . . . . . . . . . . . . . . . . .
Tachometer 69
. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . \
. . . . . . . . . .
Odometer and trip meter 70
. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Light sensitive optitron meter 71
. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Service reminder indicators and warning buzzers 72
. . . . . . . . . . . . . .
Multi−information display 82
. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Instrument panel light control 96
. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

GAUGES, METERS AND SERVICE REMINDER INDICATORS
70
ODOMETER AND TRIP METER
G13045
This meter displays the odometer and two trip meters. To
change the mode indication, use the “ODO TRIP” switch.
The “ODO TRIP” switch is located in the switch box.
G13004
Push the button to use the switch box and then push the
“ODO TRIP” switch. The odometer records the total distance the vehicle has
been driven. The twin trip meter records two different
distances independently.
For example, you can use one meter to calculate the fuel
economy and the other to measure the distance on each trip.
To change the trip meter indication from one trip to the
other, push the “ODO TRIP” change switch. To set the A
trip meter to
zero, display the A meter reading, then push
the “RESET” switch. The same applies for the B trip
meter.
The data of trip meters will be cancelled if the electrical power
source is disconnected.
After operation, be sure to close the switch box to its original
position.
CAUTION
To reduce the chance of injury in case of an accident or
a sudden stop, keep the switch box closed when not in
use while driving.

GAUGES, METERS AND SERVICE REMINDER INDICATORS
71
LIGHT SENSITIVE OPTITRONMETER
Light sensitive optitron meter reduces unwanted glare of
the instrument cluster to provide a fine view for the driver.
The reflection of the instrument cluster is adjusted
automatically depending on the lighting condition of your
surrounding.
To make an adjustment, follow the procedure below.
The reflection control switch is located in the switch box.
G13044
Push the button to use the switch box. When you push the
“MODE” switch, the present setting appears on the
multiinformation display. To change the setting, push the “MODE” switch once and then
again within 6 seconds. Each time you push the button, the
setting changes in the following order:
1. AUTO−Norm
2. AUTO−Lo
3. AUTO−Hi
4. MANUAL−1
5. MANUAL−2
6. MANUAL−3
7. MANUAL−4
The setting display goes off automatically about 6 seconds
after the “MODE” switch is pushed. The mode shown last is
set.
After operation, be sure to close the switch box to its original
position.
CAUTION
To reduce the chance of injury in case of an accident or
a sudden stop, keep the switch box closed when not in
use while driving.

GAUGES, METERS AND SERVICE REMINDER INDICATORS
73
IF THIS INDICATOR OR
BUZZER COMES ON ...
DO THIS.
(e)Take vehicle to Lexus
dealer immediately.
(f)Stop and check.
(g)orTake vehicle to Lexus
dealer.
(h)See multi− information
display.
(i)or
Take vehicle to Lexus
dealer.
If brake system
warning light (red) is
also on, stop
immediately and
contact Lexus dealer.
IF THIS INDICATOR OR BUZZER COMES ON ...DO THIS.
(j)Close all doors.
(k)WG10If flashing, take vehicle
to Lexus dealer.
(l)WG6
Adjust tire inflation
pressure.
If light remains on,
contact Lexus dealer.
(m)WG8Take vehicle to Lexus
dealer.
(n)WG7Take vehicle to Lexus
dealer.
(o)Low fuel level
warning lightFill up tank.

GAUGES, METERS AND SERVICE REMINDER INDICATORS
74IF THIS INDICATOR OR
BUZZER COMES ON ...
DO THIS.
(p)Key reminder
buzzerTurn off the engine
switch.
(a) Brake System Warning Light (red) and Buzzer
This light comes on in the following cases when the engine
switch is selected in “IG −ON” mode.
 When the parking brake is applied ...
GS430—This light comes on fo r a few seconds when the
engine is started even after the parking brake is released.
GS300—This light comes on fo r a few seconds when the
engine switch is selected in “IG −ON” mode even after the
parking brake is released.
If you drive your vehicle without releasing the parking brake,
the buzzer sounds and the message “PARK BRAKE” appears
on the multi −information display.
 When the brake fluid level is low ...
CAUTION
It is dangerous to continue driving normally when the
brake fluid level is low.
Have your vehicle checked at your Lexus dealer in the
following case:
The light does not come on even if the parking brake is
applied when the engine is started.
 The light does not come on even if the engine is started with
the parking brake released.

GAUGES, METERS AND SERVICE REMINDER INDICATORS
78At this time, vibration may occur. However, if you depress the
accelerator pedal more firmly and slowly, you can drive your
vehicle at low speeds. Have your vehicle checked by your
Lexus dealer as soon as possible.
Even if the abnormality of the electronic throttle control system
is corrected during low speed driving, the system may not be
recovered until the engine is stopped and the engine switch is
selected in “ACC” or “OFF” mode.
Emissions inspection and maintenance (I/M) programs
Your vehicle may not pass a state emission inspection if the
malfunction indicator lamp remains on. Contact your Lexus
dealer to check your vehicle’s emission control system and
OBD (On
−Board Diagnostics) system before taking your
vehicle for the inspection.
For details, see “Emissions inspection and maintenance (I/M)
programs” on page 497.
(h) Master Warning Light
If any system malfunctions, this warning light comes on or
flashes together with a warning tone, and a warning message
appears on the multi−information display. When the cause of
the problem is eliminated, the warning tone and message on
the display will turn off.
(i) ”ABS” Warning Light
The light comes on when the engine switch is selected in
“IG−ON” mode.
GS430—If the anti−lock brake system and the brake assist
system work properly, the light turns of f in a few seconds after
the engine is started. Thereafter, if either system malfunctions,
the light comes on again.
GS300—If the anti−lock brake system and the brake assist
system work properly, the light turns of f in a few seconds after
the engine switch is selected in “IG−ON” mode. Thereafter, if
either system malfunctions, the light comes on again.
When the “ABS” warning light is on, the anti− lock brake system
and the brake assist system do not operate, but the brake
system still operates conventionally.
If either of the following conditions occur, this indicates a
malfunction somewhere in the components monitored by
the warning light system. Contact your Lexus dealer as
soon as possible to service the vehicle.
 The light does not come on when the engine switch is
selected in “IG −ON” mode.
 The light remains on after the engine is started (GS430), or
remains on after the engine switch is selected in “IG −ON”
mode (GS300).
 The light comes on while you are driving.
A warning light turning on briefly during operation does not
indicate a problem.

GAUGES, METERS AND SERVICE REMINDER INDICATORS
82
MULTIINFORMATION DISPLAY
G13037
The multiinformation display provides various
information, including your vehicle’s driving condition,
outside temperature, and warning messages if your
vehicle is in trouble.
During ordinary driving, cruise information or graphic
information is displayed. However, if any problem occurs
in your vehicle, the display changes to a warning message
screen.
(a) Cruise information
The following information is shown with the engine switch
in “IGON” mode. Each time you push the “DISP” switch,
the displayed information is changed.
 Outside temperature
 Available driving distance
 Average fuel consumption after being refueled
 Current fuel consumption
 Blank
The displayed cruise information values indicate the general
driving condition and may not always reflect precise and actual
conditions.
 Outside temperature
g13047
The outside temperature is displayed. For details, see
“Outside temperature display” on page 106.

GAUGES, METERS AND SERVICE REMINDER INDICATORS
83
Available driving distance
g13039
The available driving distance is calculated and displayed
depending on the amount of remaining fuel.
Average fuel consumption after refueling
g13046
The average fuel consumption after refueling is
calculated and displayed based on the total driving
distance and the total fuel consumption after refueling.
The value is updated every 10 seconds.
When refueling, be sure to stop your vehicle and turn the
engine switch off.
The average fuel consumption could not be calculated in either
of the following cases:
 Refueled by opening the fuel filler door using the manual
lever in the trunk
 Refueled with a small quantity of gasoline
Current fuel consumption
g13040
The current fuel consumption is calculated and displayed
based on the driving distance and the fuel consumption
at 20 revolutions of the engine.
The value is updated every 0.5 seconds.
If you are driving at low speeds just before stopping, the
accurate figure may not be shown.