steering Lexus GS430 2006 Scheduled Maintenance Guide / LEXUS 2006 GS430/GS300 FROM JAN. 2006 PROD. (OM30786U) Workshop Manual
[x] Cancel search | Manufacturer: LEXUS, Model Year: 2006, Model line: GS430, Model: Lexus GS430 2006Pages: 632, PDF Size: 10.16 MB
Page 409 of 632
STARTING AND DRIVING
385
Intuitive parking assist failure warning
If an error is detected when the intuitive parking assist is
turned on, the vehicle symbol comes on or flashes with
beeping sounds.
At this time steering guidance is temporarily stopped.
However, the sensors functioning properly continue their
obstacle detection. For details, see “When the detection range
of the sensors is shorter” on page 388.
The intuitive parking assist failure warning display is not given
in either of the following operations:
Changing to another screen
Turning off the main switch for the intuitive parking assist When snowflakes or mud gets on the sensors
G31062a
1
Multi information display 2Screen
If foreign matter gets on the sensors and the intuitive
parking assist cannot detect the object properly, the
above message appears. At this time, the vehicle symbol
and the indicator bars corresponding to the faulty
sensors flash for about 7 seconds and 2 beeps sound 5
times.
After about 7 seconds, the sensor indicator bars will
cease flashing, however will stay lit until the affected
sensor is cleaned. Furthermore, the vehicle symbol will
continue to flash until the affected sensor is cleaned.
The above illustration shows the sensor on the left front of the
vehicle malfunctioning.
If the failure warning does not go off even after the foreign
matter is removed, the intuitive parking assist may be
malfunctioning. Have it checked by your Lexus dealer.
Page 410 of 632
STARTING AND DRIVING
386When the sensor is malfunctioning
G31063a
1
Multi information display 2Screen
If the sensor cable is broken and the intuitive parking
assist cannot detect the object properly, the above
message appears. At this time, the indicator bars
corresponding to the faulty sensor flash for about 7
seconds and 2 beeps sound 5 times.
The indicator bars continue lighting after flashing.
The above illustration shows the sensor on the right rear of the
vehicle malfunctioning.
If this message appears, have the sensor checked by your
Lexus dealer. When the steering sensor is malfunctioning
G31064
If the steering sensor cable is broken and signals cannot
be received, the vehicle symbol comes on and the
steering guide symbol and arrows flash.
If only the steering sensor is malfunctioning, the warning
appears only on the multi
−information display.
If this warning appears, have the sensor checked by your
Lexus dealer as soon as possible.
Page 411 of 632
STARTING AND DRIVING
387
When
the neutral point of the steering sensor is unknown
G31065
If the memorized neutral point of the steering is erased by
replacing the battery, the vehicle symbol, steering guide
symbol and arrows come on.
If only the neutral point of the steering sensor is unknown, the
warning appears only on the multi −information display.
If this warning appears, calibrate the neutral point of the
steering using either of the following:
Turn the steering wheel either way fully and then in the
opposite direction fully and slowly, with the vehicle stopped.
Drive on roads (with as few curves as possible and without
backing up) for more than about 5 minutes.
If this warning goes out, the calibration of the steering neutral
point is completed. If the warning still remains on, have the
sensor checked by your Lexus dealer as soon as possible. As the intuitive parking assist might be malfunctioning in
the following cases, have it checked by your Lexus dealer.
The indicator in the instrument cluster does not come on
and a beep does not sound even when the intuitive parking
assist main switch is turned on.
The warning comes on despite no obstacle around the
vehicle.
Page 412 of 632
STARTING AND DRIVING
388
When the detection range of the sensors is
shorter
In the following cases, the sensors will detect an obstacle
about 50 cm (1.5 ft.) from either front corner of the vehicle
and the steering guidance will be stopped. Accordingly,
the tire orientation symbol on the screen does not appear.
And only the warning according to the distance up to the
obstacle is given.
a. Any one of the sensors is malfunctioning.
b. Any one of the steering sensors is malfunctioning.
c. The steering sensor signal cannot be received properly.
d. The correct vehicle information cannot be given due to
extremely low battery voltage.
e. Proper steering detection (going straight) cannot be
detected
In case of a., when the intu itive parking assist returns to
normal, the steering guidance also comes back automatically.
In case of b. through e., the steering guidance also comes back
automatically after the neutral point of the steering sensor
calibration is completed.
Rear view monitor display (Vehicles with rear
view monitor system)
G31066
On vehicles equipped with rear view monitor system, a
warning appears on the right top of the rear view monitor
in the following conditions.
When the selector lever is put in “R” and the rear view
monitor is turned on.
When the intuitive parking assist main switch is turned on
and any sensor detects an obstacle.
Although “Display Off” is selected in the intuitive parking assist
setting screen, the warning appears on the right top of the rear
view monitor.
Page 413 of 632
STARTING AND DRIVING
389
Dual sensors
G31067
1About 50 cm (1.5 ft.) to about 100 cm (3.0 ft.)
2About 37.5 cm (1.1 ft.) to about 50 cm (1.5 ft.)
3About 25 cm (0.8 ft.) to about 37.5 cm (1.1 ft.)
4Less than about 25 cm (0.8 ft.)
When the intuitive parking assist determines that the
collision will be unavoidable:
The indicator will flash yellow depending on the distance to the
obstacle. When the distance between the vehicle and the
obstacle is less than about 25 cm (0.8 ft.), the yellow indicator
will turn red.
When the intuitive parking assist determines that the
collision will be avoided by changing the steering:
The indicator will flash yellow depending on the distance to the
vehicle. The steering guide symbol and arrow do not appear. When the intuitive parking assist determines that the
collision will be avoided with the present steering angle:
The indicator will come on in green.
However, if the sensors detect and determine an obstacle at
an angle to the front of the vehicle, the indicator will not come
on.
Beeps (except for avoidable collisions at the present
steering angle):
As distance to the obstacle gets closer, the interval of the
intermittent
sound gets shorter, and then finally to a continuous
sound when the distance between the vehicle and the obstacle
is less than about 25 cm (0.8 ft.).
CAUTION
When an obstacle is detected within about 25 cm (0.8
ft.) from the vehicle, the dual sensors will change the
determination to an unavoidable collision.
With long obstacles such as walls, the decision of the
sensor may change as the obstacle gets closer; from
certain avoidance to avoidance if steering is
changed; from certain avoidance to unavoidable
collision; and there are also times when the decision
will be changed from avoidance if steering is
changed, to certain collision.
When you move your vehicle, be sure to confirm a safe
distance around your vehicle with your eyes and drive
slowly, or an accident or injury may result.
Page 436 of 632
STARTING AND DRIVING
412
CAUTION
Deceleration cruising function and approach
warning do not operate when the vehicle ahead is at
a stop or driving very slowly.
While vehicle to vehicle distance control is on (on
follow up cruising), acceleration and deceleration
are automatically performed in proportion to the
speed of the vehicle ahead detected. However, if the
vehicle ahead of you decelerates abruptly or if
another vehicle cuts in ahead of you, your vehicle
may collide with the vehicle ahead unless you
manually depress the brake pedal to slow down your
vehicle. If you need to accelerate because the vehicle
ahead or you changes lanes, then depress the
acceleration pedal.
Depending on the road configuration (curved roads,
left and right continuous curved roads, driving at the
start or end of the curve, narrow driving lanes due to
road construction) or your vehicle condition
(steering wheel maneuvering, position in the lane or
unstable driving because of an accident or
breakdown), vehicles in other lanes or surrounding
objects will be detected, resulting in a control failure
or the activated approach warning. This may also
result in a very close distance between vehicles due
to a failure to detect the vehicle ahead. Maneuvering
the steering wheel in response to a violent lateral
wind will cause similar conditions.
(d) Changing vehicle to vehicle distance
G31016
1 Long 2Middle 3Short
You can select one of the following vehicle to vehicle
distances: “Long”, “Middle” or “Short”. Each time you
pull the distance switch briefly toward you, the setting
changes from “Long” to “Middle” to “Short” and then
back to “Long”. You can confirm the setting on the
multi information display.
It should be noted that pushing the “DISP” switch will change
to another screen.
Your vehicle speed changes in proportion to the speed of
the vehicle ahead, maintaining the selected distance.
However, if the vehicle speed is slower, the selected
distance will be shorter than the designated distance.
When the vehicle− to−vehicle distance control mode is
activated or the multi−information display indicates “RADAR
READY”, the vehicle −to −vehicle distance setting can be
changed.
Page 448 of 632
STARTING AND DRIVING
424
ADAPTIVE VARIABLE SUSPENSIONSYSTEM (GS430 only)
G31041
1Sport position 2Normal position
The adaptive variable suspension system controls the
suspension according to the road and driving conditions.
Selecting an optimum driving mode allows good vehicle
posture and steering wheel operation in conjunction with
variable gear ratio steering system and electric power
steering system.
Sport mode: Suitable for sporty type driving, such as on
winding mountain roads and high speed driving.
Normal mode: Suitable for ordinary driving.
To turn on the sport mode, push the selector switch on the
“SPORT” side. The indicator comes on in the instrument
cluster.
To change to the normal mode, push the switch to the “NORM”
side.
TRACTION CONTROL SYSTEM
The traction control system automatically helps prevent
the spinning of drive wheels when the vehicle is started or
accelerated on slippery road surfaces.
When the engine switch is selected in “IG −ON” mode, the
system automatically turns on.
CAUTION
Under certain slippery road conditions, full traction of
the vehicle and power against drive wheels cannot be
maintained, even though the traction control system is
in operation. Do not drive the vehicle under any speed
or maneuvering conditions which may cause the
vehicle to lose traction control. In situations where the
road surface is covered with ice or snow, your vehicle
should be fitted with snow tires or tire chains. Always
drive at an appropriate and cautious speed for the
present road conditions.
Page 451 of 632
STARTING AND DRIVING
427
VEHICLE STABILITY CONTROLSYSTEM
The vehicle stability control system helps provide
comprehensive control of the systems such as anti lock
brake system, traction control, engine control, etc. This
system automatically controls the brakes and engine to
help prevent the vehicle from skidding when cornering on
a slippery road surface or operating steering wheel
abruptly.
The vehicle stability control system is activated when the
vehicle speed is about more than 15 km/h (9 mph).
You may hear a sound in the engine compartment for a few
seconds just after the vehicle begins to move. This means that
the system is in the self− check mode, but does not indicate a
malfunction.
CAUTION
Do not rely excessively on the vehicle stability
control system. Even if the vehicle stability control
system is operating, you must always drive carefully
and attentively to avoid serious injury. Reckless
driving will result in an accident. If the slip indicator
light blinks, sounding an alarm, special care should
be taken while driving.
Only use tires of specified size. The size,
manufacturer, brand and tread pattern for all 4 tires
should be the same. If you use the tires other than
specified, or different type or size, the vehicle
stability control system may not function correctly.
When replacing the tires or wheels, contact your
Lexus dealer.
In situations where the road surface is covered with
ice or snow, your vehicle should be fitted with snow
tires or tire chains.
Page 455 of 632
STARTING AND DRIVING
431
VARIABLE GEAR RATIO STEERING SYSTEM (GS430 only)
The variable gear ratio steering system adjusts the wheel
turning angle depending on the vehicle speed and how
much you turn the steering wheel.
The vehicle wheel turning angle will be changed with a smaller
degree of wheel maneuvering when you are driving at very low
speed such as when putting your vehicle into a garage.
When you start or stop the engine, you may hear a small noise
and the steering wheel may move slightly. This is caused when
the system starts or stops, and does not indicate a malfunction.
In the following cases, to prevent the system from overheating,
the system could be temporarily deactivated with the change
in the center position of the steering wheel. This is not a
malfunction. After the cause of the problem is eliminated, the
system will return to normal automatically after a few minutes.
If you continue maneuvering the steering wheel when the
vehicle is stopped or running at very low speed
If you continue driving holding the steering wheel to the
extreme right or left
If you maneuver the steering wheel immediately after
starting the engine at less than about −30C (− 22F) While the system is not functioning, a larger degree of wheel
maneuvering is needed during driving at low speed. If the
center position of the steering wheel is changed frequently,
have your vehicle inspected at your Lexus dealer.CAUTION
Take due care especially when driving at low speed as
the vehicle changes direction in greater proportion to
the steering wheel maneuvering.
NOTICE
Do not disconnect the battery with the steering wheel
turned, or the center position of the steering wheel
could be slightly and temporarily changed. However,
after driving for a short while, the system will return to
normal
and the center position of the steering wheel will
be in the appropriate position.
If you disconnect and reconnect the battery terminal, the
system is reset temporarily. However, it is no problem to drive.
Drive for a short while, the system will be set automatically and
return to normal.
Page 456 of 632
STARTING AND DRIVING
432
Variable gear ratio steering system failure
warning
G31044
If there is any malfunction in the system, the above message
appears and the master warning light comes on.
If the warning message and light come on while driving, the
system is not working. Although conventional steering
operates when maneuvered, a larger degree of wheel
maneuvering (than at the time when the system is functioning
properly) is needed when driving at low speed. At this time, the
center position of the steering wheel could be changed.
Although it is no problem to continue driving, have your vehicle
repaired at your Lexus dealer.
VEHICLE DYNAMICS
INTEGRATED MANAGEMENT (GS430 only)
Vehicle Dynamics Integrated Management (VDIM) helps
manage control for vehicle stability control system,
anti lock brake system, brake assist system, traction
control system, engine output control, hill start assist
control system and also manages variable gear ratio
steering system and electric power steering system.
In order to control sudden steering wheel operation and
the sideslip on slippery road surfaces, this system
provides excellent vehicle stability by automatically
controlling the brake, engine output and front wheel
angle.
The state of the tires will affect the performance of the vehicle
dynamics integrated management system. Be sure to check
the following:
Are tires of specified size installed?
Are tires of identical type installed?
Do the tires have stipulated tire pressure?
Are the tires worn?
A problem with the tires or modified suspension systems will
have an adverse effect on the system and may cause a
malfunction, so be careful.