reset Lexus GX470 2006 Gauges, Meters and Service Reminder Indicators / LEXUS 2006 GX470 (OM60B99U) User Guide

GAUGES, METERS AND SERVICE REMINDER INDICATORS
71
Average vehicle speed is calculated and displayed based
on total driving distance and total driving time with the
engine running.
The displayed value is updated every 10 seconds.
To reset the calculations, push and hold the “RESET” button for
more than 1 second.

Barometer
 U.S.A.
Canada

GAUGES, METERS AND SERVICE REMINDER INDICATORS
73
In altimeter mode, the approximate altitude is displayed.
The displayed altitude ranges from
−1500 ft. (−500 m) up to
13000 ft. (4000 m).
As the altitude value is converted from the atmospheric
pressure, it can be easily affected by air motion and
temperature, so the indication may vary. The indicated altitude
of a single position may deviate according to the atmospheric
pressure and temperature.
The displayed value is updated every 2 seconds.
RECTIFICATION OF THE ALTITUDE
Rectification is valid only when the correct altitude is known.
While the altitude mode is on the display, push the “
” or “”
button to increase or decrease the altitude by 50 ft. (10 m).
To reset the rectified altitude, push and hold the “RESET”
button for more than 1 second. 
Elapsed time U.S.A.
Canada

GAUGES, METERS AND SERVICE REMINDER INDICATORS
74The time that has elapsed since the engine started is
displayed.
When the engine is started,
driving time is counted from 0:00.
Up to 19:59 (19 hours, 59 minutes) can be displayed. When
the driving time exceeds 19:59, the counter returns to 0:00.
To reset the calculations, push and hold the “RESET” button for
more than 1 second.
INSTRUMENT PANEL LIGHT CONTROL
To adjust the brightness of the instrument panel lights,
turn the dial.
With the dial turned fully up, the intensity of the instrument
panel lights will not be reduced when the headlight switch is on.
If the instrument panel light control dial is turned fully down, the
foot lights will turn off.

AUDIO
239
(b) Presetting a station
1. Tune in the desired station.
2. Push one of the station selector buttons (1 — 6) and
hold it until a beep is heard. This sets the station to the
button and the button number (1 — 6) appears on the
display.
Each
button can store one AM station and two FM stations. To
change the preset station to a different one, follow the same
procedure.
The preset station memory is cancelled when the power
source is interrupted by battery disconnection or a blown fuse. (c) Selecting a station
Tune in the desired station using one of the following methods.
Seek tuning: Push the “SEEK” button. The radio will begin
seeking up
or down for a station of the nearest frequency and
will stop on reception. Each time you push the button, the
stations will be searched automatically one after another.
Preset tuning: Push the button (1 — 6) for the station you
want. The button number (1 — 6) and station frequency
appear on the display.
Manual tuning: Turn the “AUDIO·TUNE” knob. The radio will
step up or down to another frequency.

AUDIO
240
To scan all the frequencies: Push the “SCAN” button briefly.
“SCAN” appears on the display. The radio will find the next
station up the band, stay there for a few seconds, and then
scan again. To select a station, push the “SCAN” button a
second time.
To scan the preset stations: Push the “SCAN” button until
you hear a beep. “SCAN” appears on the display. The radio
will tune in the next preset station up the band, stay there for
a few seconds, and then move to the next preset station. To
select a station, push the “SCAN” button a second time. (d) RDS (Radio Data System)
TYPE (Program type):
When you push the “TYPE” button, the current program type
receiving from RDS station appears on the display.
If the system receives no RDS stations, “NO PTY” appears on
the display.
Each time you
pushy the “” or “ ” button, the program type
changes as in the following:
 ROCK
 EASY LIS (Easy listening)
 CLS/JAZZ (Classical music and jazz)
 R&B (Rhythm and Blues)
 INFORM (Information)
 RELIGION

AUDIO
249
Repeating a CD: Push the “RPT” button and hold it until you
hear a beep. “
” will appear on the display. The player
will repeat all the tracks on the CD you are listening to. When
the CD ends, the player will automatically go back to the first
track on the CD and replay. This process will be continued until
you push the button again to turn off the repeat feature.
(g) Random playing
“RAND” button: There are 2 random features — you can
either listen to the tracks on all the CDs in the player in random
order, or only listen to the tracks on a specific CD in random
order.
Random playing for the tracks on a CD: Push the “RAND”
button briefly. “
” will appear on the display and play
the CD you are listening to in random order. Random playing for all the tracks in the automatic
changer:
Push the “RAND” button and hold it until you hear a
beep. “
” will appear on the display and the player will
perform all the tracks on all the CDs in the automatic changer
in random order. To turn off the random feature, push “RAND”
a second time.
When a track is skipped or the system is inoperative, push the
button to reset.
(h) CD text
When you push the “TEXT” button while the CD with CD
text display function (the logo “CD TEXT” marked on the
CD) is being played, the track number, elapsed time, CD
title and then track title appear on the display.
When you push this button if the CD does not have a text
display function, “NO TITLE” appears on the display.

AUDIO
251
The DVD player will be selectable if a rear seat entertainment
system is installed in your vehicle.
“+
” switch: Use this switch to adjust the volume.
To increase the volume, push the “+” side. To decrease the
volume, push the “–” side. The volume continues to increase
or decrease while the switch is being pressed.
(a) When the radio mode is selected
“
” or “” switch: Use this switch for seek tuning or to
select a preset station.
 To select a preset station, push this switch briefly. The
station you assigned to a switch on the audio system will be
selected.
 To seek a station, push and hold this switch until you hear
a beep. The radio will begin seeking up or down for a station,
and will stop on reception.
(b) When the “TAPE” mode is selected
“
” or “” switch: Use this switch to fast forward or rewind
the tape or for automatic program selection.
 To skip forward or reward for automatic program selection,
push this switch briefly. When automatically selecting a
program, you can skip up to 9 programs at a time. See page
244 for details.
 To fast forward or rewind the tape, push this switch until you
hear a beep. To stop fast forwarding or rewinding, push and
hold the same side on the switch until you hear a beep. (c) When the “CD” mode is selected
“
” or “” switch: Use this switch to select a desired track
or CD.
 To select a desired track, push this switch briefly.
 To select a desired CD, push and hold this switch until the
desired number of the CD appears and you hear a beep.
Vehicles with rear seat entertainment system —
While the DVD player is in operation, the chapter or track can
be changed by pushing the “ ” or “” side of the switches.
CAUTION
Operate the switches with due care while you are
driving to avoid accidents.

AUDIO
263
Radio operation
(a) Listening to the radio
Push the “ON/SOURCE” button to choose either an AM or
FM station.
“AM”, “FM1” or “FM2” appears on the display.
If the front audio system receives a traffic announcement (TA)
while the rear seat audio system is in the radio mode, “TRAF”
will flash on the screen and the rear seat audio system will turn
off. When the front audio receives a traf fic announcement (TA),
the rear seat audio system cannot select the AM/FM mode. (b) Selecting a station
Tune in the desired station using one of the following methods.Seek tuning: Push and hold the “” or “” (TUNE/TRACK)
button. The radio will begin seeking up or down for a station
of the nearest frequency and will stop on reception. Each time
you push the button, the stations will be searched out one after
another.
Manual tuning: Quickly push and release the “
” or “”
(TUNE/TRACK) button. The radio will step up or down to
another frequency.
To scan the preset stations: Push the “
” or “”
(DISC/CH/PROG) button. The radio will tune in the next preset
station up the band, stay there for a few seconds, and then
move to the next preset station. To select a station, push the
“SCAN” button a second time.
You can scan only the preset stations for the band of the front
audio system. (For instructions, see “(b) Presetting a station”\
on page 239.)

AUDIO
277
1“CURSOR” button:
Indicates the control switches on the screen when the
DVD player is operated.
2Joy stick:
Select a control switch, mode switch on the screen or
the menu for the CD.
3“ENT” button:
Input the selected switch or the selected menu for the
CD.
4“SOURCE” button:
Turn on the rear seat entertainment system and selects
the mode.
5“DISPLAY” button:
Adjust the color, tone, contrast and brightness of the
screen.
6“VIDEO” button:
Turn on the video mode when your personal audio
device is connected.
7“DVD” button:
Turn on the DVD mode.
8“RETURN” button:
Skip to the predetermined scene for the CD.
9“SET UP” button:
Indicate the initial set up screen when the DVD player
is operated.
10“SEARCH” button:
Indicate the title search screen when the DVD player is
operated.
11“ANGLE” button:
Select the angle of the screen when the DVD player is
operated.
12“  ” button: Fast forwards a screen when the DVD
player is operated.
13“  ” button: Play a screen when the DVD player is
operated.
14“” button: Pause a screen when the DVD player is
operated.
15“ \b\b ” button: Reverse a screen when the DVD player
is operated.
16“TOP MENU” button:
Indicate the title selection screen for DVD video when
the DVD player is operated.
17“AUDIO” button:
Indicate the changing audi o screen when the DVD
player is operated.
18“SUB TITLE” button:
Indicate the changing subtitle screen when the DVD
player is operated.
19“MENU” button:
Indicate the menu screen for DVD video when the DVD
player is operated.
20“OFF” button:
Turn off the rear seat entertainment system.
21“TUNE/TRACK” buttons:
Operate the front audio system or select the
track/chapter when the DVD player is operated.
22“DISC/CH/PROG” buttons:
Skip directly to a desired preset station, CD, track or
chapter.

AUDIO
283
Manual tuning: Quickly push and release the “
” or “”
(TUNE/TRACK) button. Each time you push the button, the
radio will step up or down to another frequency. If you push and
hold the button, and the radio will go into the seek mode.
To scan the preset stations: You can scan only the preset
stations for the band of the front audio system. Push the “”
or “” (DISC/CH/PROG) button. The radio will tune in the next
preset station up or down the band. The station frequency will
appear on the screen.
Cassette tape player operation
(a) Playing a cassette tape
Using joy stick and the “ENT” button to select the cassette tape
mode.
“TAPE” appears on the display.
Autoreverse feature: After the cassette player reaches the
end of a tape, it automatically reverses and begins to play the
other side, regardless of whether the cassette was playing or
fast forwarding.