jump cable Lexus HS250h 2010 Owner's Manual

536
5-2. Steps to take in an emergency
HS250h_U_75033U(Canada)
If the vehicle 12-volt battery is discharged
The following procedures may be used to start the hybrid system if the vehi-
cle’s 12-volt battery is discharged.
You can also call your Lexus dealer or a qualified repair shop.
If you have a set of jumper (or booster) cables and a second vehicle
with a 12-volt battery, you can jump start your vehicle by following the
steps below.
Open the hood and fuse box
cover.
Push the tab in and lift the lid off.
Open the exclusive jump start-
ing terminal cover.
Slightly pull the tab to open the
cover.

5
When trouble arises
537
5-2. Steps to take in an emergency
HS250h_U_75033U(Canada)
Connect the jumper cables according to the following procedure:Connect a positive jumper cable clamp to the exclusive jump start-
ing terminal on your vehicle
Connect the clamp on the other end of the positive cable to the pos-
itive (+) battery terminal on the second vehicle
Connect a negative cable clamp to the negative (-) battery terminal
on the second vehicle
Connect the clamp at the other end of the negative cable to a solid,
stationary, unpainted metallic point away from the exclusive jump
starting terminal and any moving parts, as shown in the illustration. Start the engine of the second vehicle. Increase the engine
speed slightly and maintain that level for approximately 5 min-
utes to recharge the 12-volt battery of your vehicle.
Maintain the engine speed of th e second vehicle and start the
hybrid system of your vehicle by turning the “POWER” switch
to ON mode.
Make sure the “READY” indicator comes on. If the indicator
does not come on, contact your Lexus dealer.
Once the hybrid system has started, remove the jumper cables
in the exact reverse order from which they were connected.

5
When trouble arises
539
5-2. Steps to take in an emergency
HS250h_U_75033U(Canada)
CAUTION
■Avoiding battery fires or explosions
The flammable gas that may be generated by the assisting vehicle battery may
catch fire and explode. Make sure to observe the following to prevent fire or sparks.
●Make sure each jumper cable is connected to the correct terminal and that it is
not unintentionally in contact with any part other than the intended terminal.
●Do not allow the other end of the jumper cable connected to the “+” terminal to
come into contact with any other parts or metal surfaces in the area, such as
brackets or unpainted metal.
●Do not allow the + and - clamps of the jumper cables to come into contact with
each other.
●Do not allow open flame or use matches, cigarette lighters or smoke near the
battery.
■12-volt battery precautions
The 12-volt battery contains poisonous and corrosive acidic electrolyte, while
related parts contain lead and lead compounds. Observe the following precautions
when handling the 12-volt battery:
●When working with the 12-volt battery, always wear safety glasses and take care
not to allow any battery fluids (acid) to come into contact with skin, clothing or the
vehicle body.
●Do not lean over the 12-volt battery.
●In the event that battery fluid comes into contact with the skin or eyes, immedi-
ately wash the affected area with water and seek medical attention. Place a wet
sponge or cloth over the affected area until medical attention can be received.
●Always wash your hands after handling the battery support, terminals, and other
battery-related parts.
●Do not allow children near the 12-volt battery.

540
5-2. Steps to take in an emergency
HS250h_U_75033U(Canada)
NOTICE
■Exclusive jump starting terminal precaution
The exclusive jump starting terminal is to be used when charging the 12-volt battery
from another vehicle in an emergency. It cannot be used to jump start another vehi-
cle.
■When handling jumper cables
When connecting the jumper cables, ensure that they do not become entangled in
the cooling fans or belt.