Lexus IS220d 2012 Owner's Manual

189
2-3. Operating the lights and windshield wipers
2
When driving
IS250/220d/200d_EE
Automatic light off system
This system is active when the “ENGINE START STOP” switch is in IGNI-
TION ON mode and the headlight lever is in any position other than
.
When the light switch is in : The headlights turn off automatically
if the “ENGINE START STOP” switch is switched to ACCESSORY
mode or turned OFF.
When the light switch is in “AUTO”: The headlights and tail lights turn
off automatically if the “ENGINE START STOP” switch is switched to
ACCESSORY mode or turned OFF and the driver's door is opened.
Even if a door other than the driver's door is opened, the automatic light
off system will not operate.
To turn the lights on again, switch to IGNITION ON mode, or turn the light
switch off once and then back to
or .
Light reminder buzzer
A buzzer sounds when the “ENGINE START STOP” switch is turned OFF
or switched to ACCESSORY mode and the driver's door is opened while the
lights are turned on.
Automatic headlight leveling system (vehicles with discharge headlights)
The level of the headlights is automatically adjusted according to the num-
ber of passengers and the loading condition of the vehicle to ensure that the
headlights do not interfere with other road users.
Customization that can be configured at any authorized Lexus dealer or
repairer, or another duly qualified and equipped professional
Settings of the light sensor sensitivity can be changed.
(Customizable features P. 556)
NOTICE
To prevent battery discharge
Do not leave the lights on longer than necessary when the engine is not run-
ning.

190
2-3. Operating the lights and windshield wipers
IS250/220d/200d_EE
Fog light switch
The fog lights improve visibility in difficult driving conditions, such
as in rain or fog. The fog lights can be used when the headlights or
front position lights are turned on. (The rear fog lights can be used
when the front fog lights are turned on.)
Turns the front and
rear fog lights off
Turns the front fog
lights on
Turns both front and
rear fog lights on
Releasing the switch ring
returns it to .
Operating the switch ring
again turns only the rear fog
lights off.
Fron Rear

191
2-3. Operating the lights and windshield wipers
2
When driving
IS250/220d/200d_EE
Windshield wipers and washer
Intermittent windshield wiper with interval adjuster
Wiper intervals can be adjusted for intermittent operation
(wipers operate at a set interval).
Off
Intermittent wind-
shield wiper opera-
tion
Low speed wind-
shield wiper opera-
tion
High speed wind-
shield wiper opera-
tion
Temporary opera-
tion
Releasing the lever returns to
.
Increases the intermittent
windshield wiper fre-
quency
Decreases the intermittent
windshield wiper fre-
quency

192
2-3. Operating the lights and windshield wipers
IS250/220d/200d_EE
Washer/wiper operation
Wipers operate automati-
cally. (After operating several
times, the wipers operate one
more time after a short delay
to prevent dripping.)

193
2-3. Operating the lights and windshield wipers
2
When driving
IS250/220d/200d_EE
Rain-sensing windshield wipers
When is selected, the wipers will operate automatically
when the sensor detects falling rain. The system automatically
adjusts wiper timing according to rain volume and vehicle
speed.
The wiper operation is selected as follows by turning the switch
ring. When is selected, the sensor sensitivity can be also
adjusted:
Off
Rain-sensing wind-
shield wiper opera-
tion
Low speed wind-
shield wiper opera-
tion
High speed wind-
shield wiper opera-
tion
Temporary opera-
tion
Releasing the lever returns to

194
2-3. Operating the lights and windshield wipers
IS250/220d/200d_EE
Sensor sensitivity (high)
Sensor sensitivity (low)
Washer/wiper operation
Wipers operate automati-
cally. (After operating several
times, the wipers operate one
more time after a short delay
to prevent dripping.)

195
2-3. Operating the lights and windshield wipers
2
When driving
IS250/220d/200d_EE
The windshield wipers and washer can be operated when
The “ENGINE START STOP” switch is in IGNITION ON mode.
Effects of vehicle speed on wiper operation
Vehicle speed affects the following even when the wipers are not in
“AUTO” mode.
Intermittent wiper interval
Wiper operation when the washer is being used (delay until drip preven-
tion wiper sweep occurs)
Low speed wiper operation selected, wiper operation will be switched from
low speed to intermittent wiper operation only when the vehicle is station-
ary.
(However, the mode cannot be switched when the adjustment dial for the
intermittent wiper interval is set to the lowest setting.)
Raindrop sensor (vehicles with rain-sensing windshield wipers)
If the wiper switch is turned to “AUTO” position while the “ENGINE
START STOP” switch is in IGNITION ON mode, the wiper will operate
once to show that auto mode is activated.
If the temperature of the raindrop sensor is 90C (194F) or higher, or -
30C (-22F) or lower, automatic operation may not occur. In this case,
operate the wipers in any mode other than “AUTO”.
Outside rear view mirror defogger activation linked to windshield wiper
operation
The outside rear view mirror defogger automatically turns on when you
operate the windshield wipers.
The sensor judges the amount of rain-
drops.

196
2-3. Operating the lights and windshield wipers
IS250/220d/200d_EE
If no windshield washer fluid sprays
If there is washer fluid in the windshield washer fluid reservoir and no
washer fluid sprays, the nozzle may be blocked. In this case, contact any
authorized Lexus dealer or repairer, or another duly qualified and equipped
professional, and have your Lexus inspected.
Customization that can be configured at any authorized Lexus dealer or
repairer, or another duly qualified and equipped professional
Settings (e.g. drip prevention function) can be changed.
(Customizable features P. 556)
CAUTION
Caution regarding the use of windshield wipers in “AUTO” mode (vehicles
with rain-sensing windshield wipers)
The windshield wipers may operate unexpectedly if the sensor is touched or
the windshield is subject to vibration in “AUTO” mode. Take care that your
fingers or anything else do not become caught in the windshield wipers.
Caution regarding the use of washer fluid
When it is cold, do not use the washer fluid until the windshield becomes
warm. The fluid may freeze on the windscreen and cause low visibility. This
may lead to an accident, resulting in death or serious injury.
NOTICE
When the windshield is dry
Do not use the wipers, as they may damage the windshield.
When a nozzle becomes blocked
Do not try to clear it with a pin or other object. The nozzle will be damaged.
When there is no washer fluid spray from the nozzle
Damage to the washer fluid pump may be caused if the lever is pulled
toward you and held continually.

197
2-3. Operating the lights and windshield wipers
2
When driving
IS250/220d/200d_EE
Headlight cleaner switch
The headlight cleaner can be operated when
The “ENGINE START STOP” switch is in IGNITION ON mode and the
headlight switch is turned on.
Windshield washer linked operation
Only for the first time when the windshield washer is operated after the
“ENGINE START STOP” switch is turned to IGNITION ON mode with the
headlights on, the headlight cleaners will also operate once. (P. 191)
When using the headlight cleaner
The washer fluid will spray out into the surrounding area and may get on
clothes, items etc. Therefore, check the surrounding area before using the
headlight cleaner.
NOTICE
When the washer fluid tank is empty
Do not use this function when the washer fluid tank is empty. This may
cause the washer fluid pump to overheat.
Washer fluid can be sprayed on the headlights.
Press the switch to clean the
headlights.
: If equipped

198
IS250/220d/200d_EE
2-4. Using other driving systems
Cruise control
Use the cruise control to maintain a set speed without depressing the
accelerator pedal.
Indicator
Cruise control switch
Setting the vehicle speed
Press the “ON-OFF” button
to activate the cruise control.
Cruise control indicator will
come on.
Press the button again to
deactivate the cruise control.
Accelerate or decelerate the
vehicle to the desired speed,
and push the lever down to
set the speed.
The vehicle speed at the
moment the lever is released
becomes the set speed.
STEP1
STEP2

: If equipped