Lexus IS220d 2012 Owner's Manual

179
2-2. Instrument cluster
2
When driving
IS250/220d/200d_EE
*1:These lights turn on when the “ENGINE START STOP” switch is
turned to IGNITION ON mode to indicate that a system check is
being performed. They will turn off after the engine is started, or
after a few seconds. There may be a malfunction in a system if a
light does not come on, or if the lights do not turn off. Have the
vehicle inspected by any authorized Lexus dealer or repairer, or
another duly qualified and equipped professional, for details.
*2:The light flashes to indicate that the system is operating
(if
equipped)
Daytime running light
system off indicator
(P. 188)SRS airbag on-off indi-
cator (P. 140)
(vehicles
with a man-
ual trans-
mission)Engine preheating indi-
cator (P. 156)
*1

180
2-2. Instrument cluster
IS250/220d/200d_EE
CAUTION
If a safety system warning light does not come on
Should a safety system light such as the ABS and SRS warning light not
come on when you start the engine, this could mean that these systems are
not available to help protect you in an accident, which could result in death
or serious injury. Have the vehicle inspected by any authorized Lexus dealer
or repairer, or another duly qualified and equipped professional, immedi-
ately if this occurs.
Warning lights
Warning lights inform the driver of malfunctions in any of the
vehicle’s systems. (P. 467)
*:These lights turn on when the “ENGINE START STOP” switch is
turned to IGNITION ON mode to indicate that a system check is
being performed. They will turn off after the engine is started, or
after a few seconds. There may be a malfunction in a system if a
light does not come on, or if the lights do not turn off. Have the
vehicle inspected by any authorized Lexus dealer or repairer, or
(vehicles
with a
manual
transmis-
sion)
(if equipped)(for
driver)(for front
passen-
ger)
*****
*****

181
2-2. Instrument cluster
2
When driving
IS250/220d/200d_EE
Multi-information display
The multi-information display presents the driver with a variety of
driving-related data, including the current outside air temperature.
Trip information (P.
182)
Displays driving range, fuel
consumption and other cruis-
ing-related information.
Lexus parking assist-sen-
sor display (if equipped)
Automatically displayed
when using Lexus parking
assist-sensor.
Satellite switch mode dis-
play
(P. 365)
This switch is used to config-
ure various function settings.
Dynamic radar cruise con-
trol display (if equipped)
(P. 202)
Automatically displayed
when using dynamic radar
cruise control.
Warning messages
(P. 4 7 3 )
Automatically displayed

182
2-2. Instrument cluster
IS250/220d/200d_EE
Trip information
Display items can be switched
by pushing the “DISP” switch.
Outside temperature
Driving range
Displays the outside air temperature.
The temperature range that can be displayed is
from -40C (-40F) to 50C (122F).
When the temperature drops to 3C (37F), the
digits of the display will flash for 10 seconds.
Displays the estimated maximum distance that
can be driven with the quantity of fuel remain-
ing.
• This distance is computed based on your aver-
age fuel consumption. As a result, the actual
distance that can be driven may differ from that
displayed.
• When only a small amount of fuel is added to
the tank, the display may not be updated.
When refueling, turn the “ENGINE START
STOP” switch off. If the vehicle is refueled
without turning the “ENGINE START STOP”
switch off, the display may not be updated.

183
2-2. Instrument cluster
2
When driving
IS250/220d/200d_EEAverage fuel consumption
Average fuel consumption after refueling
Current fuel consumption
Average vehicle speedDisplays the average fuel consumption since the
function was reset.
• The function can be reset by pushing the
“DISP” switch for longer than one second when
the average fuel consumption is displayed.
• Use the displayed average fuel consumption as
a reference.
Displays the average fuel consumption since the
vehicle was last refueled.
Use the displayed average fuel consumption as a
reference.
Displays the current rate of fuel consumption.
Displays the average vehicle speed since the
engine was started or the function was reset.
The function can be reset by pushing the “DISP”
switch for longer than one second when the aver-
age vehicle speed is displayed.

184
2-2. Instrument cluster
IS250/220d/200d_EEGear position display
(vehicles with an automatic transmission only)
Indicates the current gear, and the range of gears
that is available when the shift lever is in the D
or S position. The gear range is shown by the
number of dots () and the current gear is shown
as a number. The transmission automatically
selects the gears within the driver selected gear
range.
In the illustration to the left, a range of 6 available
gears (1 through 6) has been selected by the driver.
(The shift lever is in the D or S position with 6
ranges enabled.) It is possible for the transmission
to automatically select between all 6 of the gears.
In this case, the transmission has selected third
gear.
System check display
After switching the “ENGINE START STOP” switch to IGNITION ON
mode, “CHECK” is displayed while system operation is checked. When the
system check is complete, “COMPLETED” is displayed before returning to
the normal screen.
Outside temperature display
In the following situations, the correct outside temperature may not be dis-
played, or the display may take longer than normal to change.
When stopped, or driving at low speeds (less than 20 km/h [12 mph])
When the outside temperature has changed suddenly (at the entrance/exit
of a garage, tunnel, etc.)

185
2-2. Instrument cluster
2
When driving
IS250/220d/200d_EE
CAUTION
When the temperature of the display is extremely low
Allow the interior of the vehicle to warm up before using the liquid crystal
information display. At extremely low temperatures, the information display
monitor may respond slowly, and display changes may be delayed.
For example, there is a lag between the driver’s downshifting and the new
gear number appearing on the display. In this case, wait until the display
changes and take care not to downshift again, causing rapid and excessive
engine braking and possibly an accident resulting in death or serious injury.

186
IS250/220d/200d_EE
2-3. Operating the lights and windshield wipers
Headlight switch
Turning on the high beam headlights
With the headlights on, push
the lever forward to turn on
the high beams.
Pull the lever back to the center
position to turn the high beams
off.
Pull the lever toward you to
turn on the high beams.
Release to turn them off. You
can flash the high beams with
the headlights on or off.
The headlights can be operated manually or automatically.
Off
The front position,
tail, license plate
and instrument
panel lights turn on.
The headlights and
all lights listed
above turn on.
The headlights and
front position lights
turn on and off auto-
matically
(when the
“ENGINE START
STOP” switch is in
IGNITION ON

187
2-3. Operating the lights and windshield wipers
2
When driving
IS250/220d/200d_EE
Manual headlight leveling dial (vehicles without discharge head-
lights)
The level of the headlights can be adjusted according to the num-
ber of passengers and the loading condition of the vehicle.
Raises the level of the head-
lights
Lowers the level of the head-
lights
Guide to dial settings
Occupancy and luggage load conditionsDial positionOccupantsLuggage load
DriverNone0
Driver and front
passengerNone0
All seats occupiedNone2
All seats occupiedFull luggage loading3
DriverFull luggage loading4

188
2-3. Operating the lights and windshield wipers
IS250/220d/200d_EE
Daytime running light system (if equipped)
Vehicles with halogen headlights
To make your vehicle more visible to other drivers, the head-
lights turn on automatically (at a reduced intensity) whenever
the engine is started. Daytime running lights are not designed for
use at night.
Vehicles with discharge headlights
To make your vehicle more visible to other drivers, the front
position lights turn on automatically (at a increased intensity)
whenever the engine is started. Daytime running lights are not
designed for use at night.
Deactivating daytime running light (vehicles with discharge
headlights)
How to switch: P. 365
“DRL OFF” turns on when the daytime running light is deactivated.
Headlight control sensor
The sensor may not function properly if
an object is placed on the sensor, or any-
thing that blocks the sensor is affixed to
the windshield.
Doing so interferes with the sensor
detecting the level of ambient light and
may cause the automatic headlight sys-
tem to malfunction