steering wheel Lexus IS300 2005 Basic Functions / LEXUS 2005 IS300 (OM53489U) Owner's Guide

STEERING WHEEL AND MIRRORS
185
NOTICE
Do not put magnets or a metal object near the inside rearview mirror. Doing this may cause malfunction of thecompass sensor.
CALIBRATING THE COMPASS (deviation calibration)
The direction display on the compass deviates from the true
direction determined by the earth's magnetic field. The amount
of deviation varies according to the geographic position of the
vehicle.
To adjust for this deviation, stop the vehicle and push the
button for longer than about 6 seconds until the number (1±15)
appears on the display. Then push the button again, referring
to the following map to select the number of the zone where the
vehicle is.
SV16186

Zone number
If the direction is displayed several seconds after adjustment,
the calibration is finished.
04 06.30

STEERING WHEEL AND MIRRORS
186
CAUTION
Do not adjust the display while the vehicle is moving. Be
sure to adjust the display only when the vehicle is
stopped.
CALIBRATING THE COMPASS (circling calibration)
SV16139
ªCº appears on the display in case the circling calibration is
required due to a drastic change in the magnetic field. To rec tify
this, follow the calibration procedure below.
SV16079
Drive the vehicle slowly (at 8 km/h (5 mph) or lower) in a circle
until the direction is displayed. If there is not enough space to
drive in a circle, drive around the block until the direction is
displayed.
After driving in 1 to 3 circles in the above method, calibration
is complete with the direction shown on the display.
If calibration cannot be performed because of the magnetized
vehicle, etc., take your vehicle to Lexus dealer.
 Do not perform circling calibration of the compass in a place
where the earth's magnetic field is subject to interference by
artificial magnetic fields (underground parking, under a
steel tower, between buildings, roof parking, near a crossing, near a large vehicle, etc.).
 During calibration, do not operate electric systems (moon
roof, power windows, etc.) as they may interfere with the calibration.
04 06.30

STEERING WHEEL AND MIRRORS
187
CAUTION
When doing the circling calibration, be sure to secure
a wide space, and watch out for people and vehicles
in the neighborhood. Do not violate any local traffic
rules while performing circling calibration.
 Do not adjust the display while the vehicle is moving.
Be sure to adjust the display only when the vehicle is
stopped.
VANITY MIRRORS
SV14008
To use the vanity mirrors, swing the sun visor down and
open the cover.
The vanity light comes on when you open the cover.
04 06.30

STEERING WHEEL AND MIRRORS
188
04 06.30

STARTING AND DRIVING
234
To allow proper operation of your vehicle's
ventilation system, keep the inlet grilles in front of the
windshield clear of snow, leaves, or other
obstructions.
 If you smell exhaust fumes in the vehicle, drive with
the windows open and the trunk lid or back door
closed. Have the cause immediately located and
corrected.BEFORE STARTING THE ENGINE
1. Check the area around the vehicle before entering it.
2. Adjust seat position, seatback angle, head restraint height
and steering wheel angle.
3. Adjust the inside and outside rear view mirrors.
4. Lock all doors.
5. Fasten seat belts.
Remember to check that the service reminder indicators
function when turning the key to ªONº, and check the fuel
gauge to see that you have sufficient fuel.
04 06.30

STARTING AND DRIVING
235
IGNITION SWITCH WITH STEERINGLOCK
SS31002
ªSTARTº ± Starter motor on. The key will return to the
ªONº position when released.
For starting tips, see page 237.
ªONº ± Engine on and all accessories on.
This is the normal driving position.
NOTICE
Do not leave the key in the ªONº position if the engine
is not running. The battery will discharge and theelectronic ignition system could be damaged.
ªACCº ± Accessories such as the radio operate, but the
engine is off. If you leave the key in the ªACCº or ªLOCKº position and open
the driver's door, a buzzer will remind you to remove the key.*
NOTE: *The volume or interval of beep sound can be
changed. Ask your Lexus dealer for details.
SS31003
ªLOCKº ± Engine is off and the steering wheel is locked.
The ignition key can be removed only at this position.
Manual transmission: To turn the key from ªACCº to the
ªLOCKº position, you must push in the key.
Automatic transmission: To turn the key from ªACCº to the
ªLOCKº position you must put the transmission selector lever
in the ªPº position and you must push in the key.
Once you remove the key, the engine immobilizer system is
automatically set. See ªEngine immobilizer systemº on page
12.
04 06.30

STARTING AND DRIVING
236When starting the engine, the key may seem stuck at the
ªLOCKº position. To free it, first be sure the key is pushed all
the way in, and then rock the steering wheel slightly while
turning the key gently.
If, in an emergency, you must turn the engine off while the
vehicle is moving, turn the key only to ªACCº.
CAUTION
For manual transmission:
Never remove the key when the vehicle is moving, as
this will lock the steering wheel and result in loss of
steering control.
PARKING BRAKE
SV31017
To set: Pull up the lever. For better holding power, first
depress the brake pedal and hold it while setting the
parking brake.
To release: Pull up the lever slightly (1) , press the lock
release button (2), and lower (3).
To remind you that the parking brake is set, the parking brake
reminder light in the instrument panel remains on until you
release the parking brake.
CAUTION
Before driving, make sure the parking brake is fully
released
and that the parking brake reminder light is off.
04 06.30

STARTING AND DRIVING
241
5. Release
the parking brake and brake pedal. Depress the
accelerator pedal slowly for smooth starting.
In normal cruising, the vehicle will start in the first gear and
automatically shift up to the most suitable gear. On inclines,
declines or winding roads, etc., the vehicle shifts up and down
automatically according to the running conditions to obtain the
suitable driving power and engine braking.
When the lever is in ª3º position, the automatic transmission
system will select the most suitable gear for the running
conditions such as hill climbing, hard towing, etc.
If you need to accelerate rapidly while driving, depress the
accelerator pedal to the full throttle position. This provides
more acceleration by automatically downshifting the
transmission to the next lower gear or beyond, depending on
the vehicle speed.
If engine braking is needed, such as in descending a long hill,
see ª(c) Using engine brakingº.
(b) Driving in M mode
If the change lever is shifted to M position, the shift range
position can be switched over between 5 and 2 using the
shift switch on the steering wheel instead of operating the
change lever. The first shift range position is on 5 when
the change lever is shifted to M position.
SV31024

1ªMº position
When the selector lever is put in the ªMº position, the M MODE
indicator is shown on the instrument cluster.
04 06.30

STARTING AND DRIVING
242
SV31028

2Downshifting on the front, Upshifting on the rear
5: Fifth rangeThe most suitable gear is selected automatically
between first and fifth gears according to the vehicle speed or the running condition.
4: Fourth range The most suitable gear is selected automatically
between first and fourth gears according to the vehicle speed or the running condition. 3: Third range
The most suitable gear is selected automatically
between first and third gears according to the vehicle speed or the running condition.
Slight engine braking will be obtained on a downhill road.
Smooth running with less shifting will be obtained on an
uphill.
2: Second range First or second gear will be selected automatically
according to the vehicle speed or the running condition.
This range is used in the case that the engine braking is necessary.
The gear position being used is shown on the instrument
cluster.
Each time you push the switch located on the front of the
steering wheel, the transmission downshifts (from ª5º) to ª4º\
,
ª3º and then ª2º.
When you push the switch located on the back of the steering
wheel, the transmission upshifts to ª3º, ª4º and then ª5º\
.
For the precautions on each position, see the description on
the next page.
04 06.30

STARTING AND DRIVING
243
Warning tone sounds twice in any of the following cases:

You attempt to downshift the transmission when it is not
possible to downshift due to the high vehicle speed.
 You attempt to downshift from ª2º position.
 You attempt to upshift from ª5º position.
If the ªMº indicator flashes, there is a problem somewhere
in the system. In this case, it should be noted that you
cannot downshift or upshift the transmission using the
switches on the steering wheel. Consult with your Lexus
dealer as soon as possible. The transmission works
exactly in the same way as when you put the selector lever
in the ªDº position.
CAUTION
Be careful when downshifting on a slippery surface. The
abrupt change in engine speed could cause the vehicle
to skid or spin.
(c) Using engine braking
SV31023
To use the braking power of the engine, downshift the
transmission in the way described below:
1Shift into the ªMº position, and you push the transmission
down shift switch. The transmission will downshift to
fourth gear and engine braking will be obtained. This is
effective only when you are driving in the ªDº position or
in fifth gear (ªMº position).
When the cruise control is being used, even if you
downshift from ª5º to ª4º, engine braking will not be
enabled because the cruise control is not cancelled. If you
need to decrease the vehicle speed, see page 251.
2Shift into the ª3º position. The transmission will downshift
to third gear when the vehicle speed is or becomes lower
than the speed listed below and stronger engine braking
will be obtained.
04 06.30