ECU lexus LC500 2018 Navigation Manual

40
-$@-$I@/BWJ@0.&@ &&

2-2. Network settings
included with the Bluetooth® phone
or portable device for more details.
7 Register the Bluetooth® device
using your Bluetooth® device.
 A PIN code is not required for SSP
(Secure Simple Pairing) compatible
Bluetooth® devices. Depending on
the type of Bluetooth® device being
connected, a message confirming
registration may be displayed on the
Bluetooth® device’s screen.
Respond and operate the
Bluetooth® device according to the
confirmation message.
8 Check that the following screen is
displayed, indicating pairing was
successful.
 The system is connecting to the reg-
istered device.
 At this stage, the Bluetooth® func-
tions are not yet available.
9 Check that “Connected” is dis-
played and registration is complete.
 If an error message is displayed, fol-
low the guidance on the screen to
try again.
●If a cellular phone does not operate prop-
erly after being connected, turn the cellu- lar phone off and on and then connect it again.
■Registering from phone
When registering from the navigation
system is failed, or the phone name
doesn’t appear on the registering
screen, you need to connect the
Bluetooth® phone manually.
1 Press the “MENU” button on the
Remote Touch.
2 Select “Setup”.
3 Select “Bluetooth*” on the sub
menu.
*: The Bluetooth® word mark and logos
are registered trademarks owned by
Bluetooth SIG, Inc.
4 Select “Yes” to register the new
phone.
5 Press the button on the Remote
Touch to select “If you cannot find…”
on the bottom of the screen.

41
2
-$@-$I@/BWJ@0.&@ &&

2-2. Network settings
Basic function
6Select “Register from phone”.
7 Register the Bluetooth® device
using your Bluetooth® device.
 A PIN code is not required for SSP
(Secure Simple Pairing) compatible
Bluetooth® devices. Depending on
the type of Bluetooth® device being
connected, a message confirming
registration may be displayed on the
Bluetooth® device’s screen.
Respond and operate the
Bluetooth® device according to the
confirmation message.
8 Check that the following screen is
displayed, indicating pairing was
successful.
 The system is connecting to the reg-
istered device.
 At this stage, the Bluetooth® func-
tions are not yet available.
9 Check that “Connected” is dis-
played and registration is complete.
 If an error message is displayed, fol-
low the guidance on the screen to
try again.
●If a cellular phone does not operate prop-
erly after being connected, turn the cellu- lar phone off and on and then connect it again.
To use the Bluetooth® Audio, it is nec-
essary to register an audio player with
the system.
Once the player has been registered, it
is possible to use the Bluetooth®
Audio.
This operation cannot be performed
while driving.
For details about registering a
Bluetooth® device: P.44
1 Turn the Bluetooth® connection
setting of your audio player on.
 This function is not available when
the Bluetooth® connection setting
of your audio player is set to off.
Registering a Bluetooth® audio
player for th e first time

53
2
-$@-$I@/BWJ@0.&@ &&

2-2. Network settings
Basic function
select “OK”.
 The network that was selected Pre-
ferred Network is marked with .
 If button is pressed on Remote
Touch during displaying this screen,
the following function can be set up.
“Details”: Select to display details about the
network.
“Add Wi-Fi* network”: Select to add a
Wi-Fi® network that is not currently dis-
played.
*:Wi-Fi® is a registered trademark of
Wi-Fi Alliance®.
■Adding a Wi-Fi® network
Available networks which are not dis-
played by searching can be added.
1 Press the button on the Remote
Touch.
2 Select “Add Wi-Fi* network”.
3 Enter the network name and select
“OK”.
4 Select the security type.
5 Enter the password and select
“OK”.
*:Wi-Fi® is a registered trademark of
Wi-Fi Alliance®.
If a Wi-Fi® device is Wi-Fi Protected
Setup™ compatible, it can be con-
nected to more quickly.
1 Press the “MENU” button on the
Remote Touch.
2 Select “Setup”.
3 Select “Wi-Fi*” on the sub menu.
4 Select “Easy setup”.
5 Select “PIN code” or “Push button”
as determined by the device.
6 Operate the Wi-Fi® device to con-
nect.
*:Wi-Fi® is a registered trademark of
Wi-Fi Alliance®.
1 Press the “MENU” button on the
Remote Touch.
2 Select “Setup”.
3 Select “Wi-Fi*” on the sub menu.
4 Select “Detailed settings”.
5 Select the items to be set.
Select to change the listing order of
your preferred networks and to
Connecting quickly
Detailed Wi-Fi® settings
A

54
-$@-$I@/BWJ@0.&@ &&

2-2. Network settings
delete networks from the list.
( P.54)
Select to set automatic connection
to network on/off. When set to on,
the system will automatically con-
nect to the preferred networks that
have been registered.
Select to set the automatic connec-
tion message notification display
on/off.
Select to reset all setup items.
*:Wi-Fi® is a registered trademark of
Wi-Fi Alliance®.
Any network connected to in the past
is set as a preferred network. The pri-
ority of the networks to connect to can
be changed.
1 Select “Reorder/Remove preferred
networks”.
2 Select the desired network and
select “Move up” or “Move down”
to change the connection priority
of the network.
“Remove”: Select to delete a network.
●If a network is being connected to, pre-
ferred network settings cannot be changed.
Reception level appears on the right
upper side of the screen. ( P.18)
●Communication standards
•802.11b •802.11g•802.11n
●Security•WEP
•WPA™*
Preferred network settings
B
C
D
Wi-Fi® function operating hints
WARNING
●Use Wi-Fi® devices only when safe
and legal to do so.
●Your audio unit is fitted with Wi-Fi® antennas. People with implantable car-
diac pacemakers, cardiac resynchro- nization therapy-pacemakers or implantable cardioverter defibrillators
should maintain a reasonable distance
between themselves and the Wi-Fi®
antennas. The radio waves may affect the opera-tion of such devices.
●Before using Wi-Fi® devices, users of
any electrical medical device other than implantable cardiac pacemakers, cardiac resynchronization therapy-
pacemakers or implantable cardio- verter defibrillators should consult the manufacturer of the device for infor-
mation about its operation under the influence of radio waves.Radio waves could have unexpected
effects on the operation of such medi- cal devices.
Conditions displayed with Wi-Fi®
icon
Specifications

61
2
-$@-$I@/BWJ@0.&@ &&

2-3. Other settings
Basic function
1Press the “MENU” button on the
Remote Touch.
2 Select “Setup”.
3 Select “Vehicle” on the sub menu.
4 Select the items to be set.
Select to set vehicle customization.
*1
Select to set Lexus parking assist-
sensor. *1,2
Select to set driving mode. *1,2
Select to set valet mode. ( P.61)
*1: Refer to the “OWNER’S MANUAL”
*2: If equipped
The security system can be set to on by
entering a security code (4-digit num-
ber).
When set to on, the system will
become inoperative once the electri-
cal power source is disconnected until
the security code is entered.
1 Press the “MENU” button on the
Remote Touch.
2 Select “Setup”.
3 Select “Vehicle” on the sub menu.
4 Select “Valet mode”.
5 Enter the 4-digit personal code and
select “OK”.
6 Enter the same 4-digit personal
code again and select “OK”.
 The system will request that you
input the security code again to
confirm that you remember it cor-
rectly.
7 When valet mode activates, the
system stops and a security code
(4-digit number) standby screen is
displayed.
●If the 4-digit personal code is forgotten, please contact any Lexus retailer or
Lexus authorized repairer, or any reliable
Vehicle settings
Settings are available for vehicle
customization, Lexus parking
assist-sensor, etc.
Displaying the vehicle settings
screen
Vehicle settings screen
A
B
Setting the valet mode
C
D

62
-$@-$I@/BWJ@0.&@ &&

2-3. Other settings
repairer.
1 Enter the 4-digit personal code and
select OK.
●If an incorrect security code (4-digit
number) is entered 6 times, the system will not accept another security code (4-digit number) for 10 minutes.
If the valet mode has been acti-
vated

193
7
-$@-$I@/BWJ@0.&@ &&

7-1. Phone operation (Hands-free system for cellular phones)
Phone
made depending on the type of cellular phone you have.
●The list should group together consecu-tive entries with the same phone number and same call type. For example, two calls
from John’s mobile would be displayed as follows: John (2)
●By pressing the switch on the steer-
ing wheel, a call to the latest history item can be made.
Calls can be made using registered
contacts which can be selected from a
contact list. ( P.210)
1 Press the “MENU” button on the
Remote Touch.
2 Select “Phone”.
3 Select the “Favourites” on the sub
menu and select the desired con-
tact.
4 Select the desired number.
5 Check that the call screen is dis-
played.
Calls can be made by using contact
data which is transferred from a regis-
tered cellular phone. ( P.193)
Up to 5000 contacts (maximum of 4
phone numbers and 4 e-mail
addresses per contact) can be regis-
tered in the contact list.
■Calling from contacts list
1 Press the “MENU” button on the
Remote Touch.
2 Select “Phone”.
3 Select the “Contacts” on the sub
menu and select the desired con-
tact.
“E-mail Addresses”: Select to display all
registered e-mail addresses for the con- tact.
4 Select the desired number.
5 Check that the call screen is dis-
played.
■For PBAP compatible Bluetooth®
phones when “Automatic transfer”
is set to on ( P.206)
 Contacts are transferred automati-
cally.
■For PBAP compatible Bluetooth®
phones when “Automatic transfer”
is set to off ( P.206)
1 Select the desired item.
Select to always transfer all the
contacts from a connected cellular
phone automatically.
Select to transfer all the contacts
from a connected cellular phone
only once.
Select to cancel transferring.
By favour ites list
By contacts list
When the contact is empty
A
B
C

215
7
-$@-$I@/BWJ@0.&@ &&

7-3. What to do if...
Phone
system to on. (P.206)
■Notification of SMS/MMS/E-mail
reception on this system is set to
off.
Set notification of SMS/MMS/E-mail
reception on this system to on.
( P.205)
■Automatic message transfer func-
tion is not enabled on the cellular
phone.
Enable automatic transfer function on
the cellular phone.
■Connection confirmation display
on this system is set to on.
To turn off the display, set connection
confirmation display on this system to
off. ( P.50)
*: The engine switch is in
ACCESSORY or IGNITION ON
mode .
■The cellular phone is not close
enough to this system.
Bring the cellular phone closer to this
system.
■Radio interference has occurred.
Turn off Wi-Fi® devices or other
devices that may emit radio waves.
■The cellular phone is the most likely
cause of the symptom.
Turn the cellular phone off, remove and
reinstall the battery pack, and then
restart the cellular phone.
Enable the cellular phone’s Bluetooth®
connection.
Disable the Wi-Fi® connection of the
cellular phone.
Stop the cellular phone’s security soft-
ware and close all applications.
Before using an application installed on
the cellular phone, carefully check its
source and how its operation might
affect this system.
●For details, refer to the owner’s manual that came with the cellular phone.
New message notifications are not
displayed.
In other situations
The Bluetooth® connection status is
displayed at the top of the screen
each time the system is activated.*
Even though all conceivable mea-
sures have been taken, the symptom
status does not change.