remote control lexus LC500 2018 Owner's Guide

325
6
-$@-$I@0.@0.&@ &&

6-3. Do-it-yourself maintenance
Maintenance and care
The 12-volt battery is located in the
trunk.
■Before recharging
When recharging, the 12-volt battery pro- duces hydrogen gas which is flammable and explosive. Therefore, observe the fol-
lowing precautions before recharging:
●If recharging with the 12-volt battery
installed on the vehicle, be sure to discon- nect the ground cable.
●Make sure the power switch on the char-ger is off when connecting and discon-necting the charger cables to the 12-volt
battery.
■After recharging/reconnecting the 12- volt battery
●Unlocking the doors using the smart entry & start system may not be possible immediately after reconnecting the 12-
volt battery. If this happens, use the wire- less remote control or the mechanical key to lock/unlock the doors.
●Start the engine with the engine switch in ACCES-
SORY mode. The engine may not start with the engine switch turned off. However, the
engine will operate nor- mally from the second attempt.
●The engine switch mode
is recorded by the vehicle. If the 12-volt battery is reconnected, the vehicle will return the engine switch
mode to the status it was in before the 12- volt battery was disc onnected. Make sure to turn off the engine switch switch> before disconnect the 12-volt bat- tery. Take extra care when connecting the 12-volt battery if the engine switch
mode prior to discharge is unknown.
If the engine will not start even after multiple attempts at all methods above, contact any authorized Lexus
retailer or Lexus authorized repairer, or any reliable repairer.
12-volt battery
Location
WARNING
■Chemicals in the 12-volt battery
The 12-volt battery contains poisonous
and corrosive sulfuric acid and may pro- duce hydrogen gas which is flammable and explosive. To reduce the risk of death
or serious injury, take the following pre- cautions while working on or near the 12-volt battery:
●Do not cause sparks by touching the
12-volt battery terminals with tools.
●Do not smoke or light a match near the 12-volt battery.
●Avoid contact with eyes, skin and clothes.
●Never inhale or swallow electrolyte.
●Wear protective safety glasses when
working near the 12-volt battery.
●Keep children away from the 12-volt battery.
■Where to safely charge the 12-volt battery
Always charge the 12-volt battery in an open area. Do not charge the 12-volt bat-
tery in a garage or closed room where there is insufficient ventilation.

349
6
-$@-$I@0.@0.&@ &&

6-3. Do-it-yourself maintenance
Maintenance and care
■If the electronic key battery is depleted
The following symptoms may occur:
●The smart entry & start system and wire- less remote control will not function properly.
●The operational range will be reduced.
Prepare the following before replacing
the battery:
 Flathead screwdriver
 Small flathead screwdriver
 Lithium battery CR2032
■Use a CR2032 lithium battery
●Batteries can be purchased at any autho-
rized Lexus retailer or Lexus authorized repairer, or any reliable repairer, local electrical appliance shops or camera
stores.
●Replace only with the same or equivalent
type recommended by the manufacturer.
●Dispose of used batteries according to
the local laws.
1 Take out the mechanical key.
2 Remove the cover.
To prevent damage to the key, wrap the tip
of the screwdriver with tape.
3 Remove the depleted battery.
Insert a new battery with the “+” terminal
facing up.
Electronic key battery
Replace the battery with a new one
if it is depleted.
Items to prepare
Replacing the battery

350
-$@-$I@0.@0.&@ &&

6-3. Do-it-yourself maintenance
1Turn the engine switch switch> off.
2 Open the fuse box cover.
Engine compartment: type A fuse
box (LC500)
Left-hand drive vehicles:
Push the tab in and lift the lid off.
Right-hand drive vehicles:
Push the tab in and lift the lid off.
WARNING
■Removed battery and other parts
These parts are small and if swallowed by
a child, they can cause choking. Keep away from children. Failure to do so could result in death or serious injury.
■Certification for the electronic key
battery
CAUTION
RISK OF EXPLOSION IF BATTERY IS REPLACED BY AN INCORRECT TYPE.
DISPOSE OF USED BATTERIES ACCORDING TO THE INSTRUCTIONS
NOTICE
■When replacing the battery
Use a screwdriver of appropriate size. Applying excessive force may deform or
damage the cover.
■For normal operation after replacing the battery
Observe the following precautions to prevent accidents:
●Always work with dry hands.Moisture may cause the battery to rust.
●Do not touch or move any other com-
ponent inside the remote control.
●Do not bend either of the battery ter- minals.
Checking and replacing
fuses
If any of the electrical components
do not operate, a fuse may have
blown. If this happens, check and
replace the fuses as necessary.
Checking and replacing fuses

389
7
-$@-$I@0.@0.&@ &&

7-2. Steps to take in an emergency
When trouble arises
■When the electronic key does not work properly
●Make sure that the smart entry & start system has not been deactivated using the Remote Touch or at any authorized
Lexus retailer or Lexus authorized repairer, or any reliable repairer. If it is off, turn the function on.
●Check if battery-saving mode is set. If it is set, cancel the function. ( P.124)
Use the mechanical key (P.113) in
NOTICE
●Install the tab so that it does not cover
the clip installation position . Fail-
ure to do so may cause damage to the clip and make it impossible to install
the cover.
A
If the electronic key does not
operate properly
If communication between the
electronic key and vehicle is inter-
rupted ( P.124) or the electronic
key cannot be used because the
battery is depleted, the smart entry
& start system and wireless remote
control cannot be used. In such
cases, the doors and trunk can be
opened and the engine tem> can be started by following
the procedure below.
NOTICE
■In case of a smart entry & start system malfunction or other key-related
problems
Take your vehicle with all the electronic keys provided with your vehicle, to any authorized Lexus retailer or Lexus
authorized repairer, or any reliable repairer as soon as possible.
Locking and unlocking the
doors, opening the trunk and
using the key li nked functions

398
-$@-$I@0.@0.&@ &&

7-2. Steps to take in an emergency
ponents when the vehicle is running at a low speed for an extended period, such as in heavy traffic.
■When the 12-volt battery is removed or
discharged
●Information stored in the ECU is cleared.
When the 12-volt battery is depleted, have the vehicle inspected at any autho-rized Lexus retailer or Lexus authorized
repairer.
●Some systems may require initialization.
( P.436)
■When removing the 12-volt battery ter- minals
When the 12-volt battery terminals are removed, the information stored in the ECU is cleared. Before removing the 12-
volt battery terminals, contact any autho- rized Lexus retailer or Lexus authorized repairer.
■Charging the 12-volt battery
The electricity stored in the 12-volt battery will discharge gradually even when the
vehicle is not in use, due to natural dis- charge and the draining effects of certain
electrical appliances. If the vehicle is left for a long time, the 12-volt battery may dis-charge, and the engine
may be unable to start. (The 12-volt battery recharges automatically during driving.)
■When recharging or replacing the 12-volt battery
●In some cases, it may not be possible to unlock the doors using the smart entry &
start system when the 12-volt battery is discharged. Use the wireless remote control or the mechanical key to lock or
unlock the doors.
●The engine may not start
on the first attempt after the 12-volt bat- tery has recharged but will start normally after the second attempt. This is not a
malfunction.
●The engine switch mode
is memorized by the vehicle. When the 12-volt battery is reconnected, the system will return to the mode it was in before
the 12-volt battery was discharged.
Before disconnecting the 12-volt battery, turn the engine switch off. If you are unsure what mode the engine
switch was in before the 12-volt battery discharged, be especially careful when reconnecting the 12-volt
battery.
●If the 12-volt battery discharges, it may
not be possible to shift the shift position to other positions. In this case, the vehicle cannot be towed without lifting both rear
wheels because the rear wheels will be locked. ( P.363)
■When replacing the 12-volt battery
●Use a Central Degassing type 12-volt battery (European Regulations).
●LC500: Use a 12-volt battery that the case size is same as the previous one (LN4), 20 hour rate capacity (20HR) is
equivalent (80Ah) or greater, and per- formance rating (CCA) is equivalent (685A) or greater.
LC500h: Use a 12-volt battery that the case size is same as the previous one (LN3), 20 hour rate capacity (20HR) is
equivalent (70Ah) or greater, and perfor- mance rating (CCA) is equivalent
(600A) or greater. • If the sizes differ, the 12-volt battery can-not be properly secured.
• If the 20 hour rate capacity is low, even if the time period where the vehicle is not used is a short time, the 12-volt battery
may discharge and engine may not be able to start.
●Use a 12-volt battery with a handle. If a 12-volt battery without a handle is used, removal is more difficult.
●After exchanging, firmly attach the fol-lowing items to the exhaust hole of the 12-
volt battery. • Use the exhaust hose that was attached to the 12-volt battery before exchanging.
• Use the exhaust hole plug included with the 12-volt battery exchanged or the one installed on the battery prior to the
exchange. (Depending on the 12-volt battery to be exchanged, the exhaust hole may be plugged.)

423
8
-$@-$I@0.@0.&@ &&

8-2. Customization
Vehicle specifications
8-2.C usto miz ation
■Changing by using the meter con-
trol switches
1 Press or of the meter con-
trol switches, select .
2 Press or of the meter con-
trol switches, select the item, and
press “OK”.
3 Press or of the meter con-
trol switches, select the desired set-
ting, and press “OK”.
To go back to the previous screen or
exit the customize mode, press .
■Changing by using the Remote
Touch
1 Press the “MENU” button on the
Remote Touch.
2 Select “Setup” on the menu screen
and select “Vehicle”.
3 Select “Vehicle customisation”,
“LEXUS park assist” or “Drive
mode customisation”.
Various setting can be changed. Refer
to the list of settings that can be
changed for details.
For details on the Remote Touch, refer
to the “NAVIGATION SYSTEM
OWNER’S MANUAL”.
■When customizing using the Remote
Touch
Stop the vehicle in a safe place, apply the
parking brake, and shift the shift position to P. Also, to prevent 12-volt battery discharge,
leave the engine running while cust omizing the features.
Some function settings are changed simultaneously with other functions being cus-
Customizable features
Your vehicle includes a variety of
electronic features that can be per-
sonalized to your preferences. The
settings of these features can be
changed by using the meter control
switches, the Remote Touch or at
any authorized Lexus retailer or
Lexus authorized repairer, or any
reliable repairer.
Customizing vehicle features
WARNING
■During customization
As the engine needs to be running during customi-
zation, ensure that the vehicle is parked in a place with adequate ventilation. In a closed area such as a garage, exhaust
gases including harmful carbon monox- ide (CO) may collect and enter the vehi-cle. This may lead to death or a serious
health hazard.
NOTICE
■During customization
To prevent 12-volt battery discharge,
ensure that the engine is running while customizing features.
Customizable features

424
-$@-$I@0.@0.&@ &&

8-2. Customization
tomized. Contact any authorized Lexus retailer or Lexus authorized repairer, or
any reliable repairer.
Settings that can be changed using the Remote Touch
Settings that can be changed using the meter control switches
Settings that can be changed by any authorized Lexus retailer or Lexus autho-
rized repairer, or any reliable repairer
Definition of symbols: O = Available, — = Not available
■Gauges, meters and multi-information display ( P.82, 88, 92)
Function*1Default settingCustomized setting
Language*2English
French
—O—
German
Spanish
Italian
Russian
Units*2km (L/100 km)km (km/L)OO—miles (MPG)
Eco Driving Indicator Light*3OffOn
(Self-lighting)—O—
EV indicator*4On
(Self-lighting)Off—O—
Drive information 1
Current fuel
economy
*5—O—Average fuel
economy
(after reset)
Drive information 2
Distance
(driving range)
*5—O—Average vehi-
cle speed
(after reset)
Pop-up displayOnOff—O—
Ring position memoryOffOn—O—
A
B
C
ABC

429
8
-$@-$I@0.@0.&@ &&

8-2. Customization
Vehicle specifications
■Smart entry & start system and wireless remote control (P.113, 122)
■Smart entry & start system (P.122)
Driver’s door linked door unlock-
ing functionOnOffO—O
Locking/unlocking of the trunk
when both side doors are
locked/unlocked
OnOff——O
Time elapsed before the door lock
indicator lights turn off30 seconds
1 minute
——O10 minutes
20 minutes
FunctionDefault settingCustomized setting
Operation signal (Emergency
flashers)OnOffO—O
Time elapsed before automatic
door lock function is activated if
door is not opened after being
unlocked
30 seconds
60 seconds
——O120 seconds
Open door warning buzzerOnOff——O
FunctionDefault settingCustomized setting
Smart entry & start systemOnOffO—O
Smart door unlockingBoth side doorsDriver’s doorO—O
Number of consecutive door lock
operations
As many as
desired2 times——O
FunctionDefault settingCustomized settingABC
ABC
ABC

430
-$@-$I@0.@0.&@ &&

8-2. Customization
■Wireless remote control (P.113)
■Driving position memory (P.140)
■Steering wheel (P.145)
FunctionDefault settingCustomized setting
Wireless remote controlOnOff——O
Unlocking operation
Both side doors
unlocked in one
step
Driver’s door
unlocked in one
step, both side
doors unlocked in
two steps
O—O
Trunk unlocking operationPress and hold
(short)
One short press
——O
Push twice
Press and hold
(long)
Off
FunctionDefault settingCustomized setting
Selecting the door linking driving
position memory with door unlock
operation
Driver’s doorBoth side doors——O
FunctionDefault settingCustomized setting
Auto tilt & telescopic away functionTilt only
Telescopic only
O—OTilt & telescopic
Off
ABC
ABC
ABC

431
8
-$@-$I@0.@0.&@ &&

8-2. Customization
Vehicle specifications
■Outside rear view mirrors (P.147)
■Power windows (P.150)
■Turn signal lever (P.186)
■Automatic light control system (P.191)
FunctionDefault settingCustomized setting
Automatic mirror folding and
extending operation
Linked to the
locking/unlock-
ing of the doors
Off
——OLinked to operation
of the engine switch

Linked mirror function when
reversingOnOff——O
FunctionDefault settingCustomized setting
Mechanical key linked operationOffOn——O
Wireless remote control linked
operationOffOn——O
Wireless remote control linked
operation signal (buzzer)OnOff——O
FunctionDefault settingCustomized setting
The number of times the turn signal
lights flash automatically when the
turn signal lever is moved to the
first position during a lane change
3
5
——O7
Off
FunctionDefault settingCustomized setting
Light sensor sensitivityStandard-2 to 2O—O
Follow me home
(Time elapsed before headlights
automatically turn off)
30 seconds
60 seconds
——O90 seconds
120 seconds
ABC
ABC
ABC
ABC