maintenance lexus LC500 2018 Service Manual

336
-$@-$I@0.@0.&@ &&

6-3. Do-it-yourself maintenance
4Press or of the meter con-
trol switches and select .
5 Press or of the meter con-
trol switches and select “Vehicle
Settings”, and then press “OK”.
6 Press or of the meter con-
trol switches and select “TPWS
SET”, and then press “OK”.
7 Press or of the meter con-
trol switches and select “Set tire
pressure”, and then press and hold
“OK” until the tire pressure warning
light starts blinking.
A message is displayed on the multi-infor- mation display. Also, “--” is displayed for inflation pressure of each tire on the multi-
information display while the tire pressure warning system determines the position.
8 Drive the vehicle at approximately
40 km/h (25mph) or more for
approximately 10 to 30 minutes.
When initialization is complete, the infla- tion pressure of each tire will be displayed on the multi-information display.
Depending on the vehicle and driving con- ditions, initialization may take up to
approximately 1 hour to complete.
■The initialization operation
●Make sure to carry out initialization after
adjusting the tire inflation pressure. Also, make sure the tires are cold before carrying out initialization or tire inflation
pressure adjustment.
●If you have accidentally turned the engine
switch off during initial- ization, it is not ne cessary to manually restart the initializatio n again, as initializa-
tion will restart automatically the next time the engine switch is turned to IGNITION ON mode mode>.
●If you accidentally perform initialization
when initialization is not necessary, adjust the tire inflation pressure to the specified level when the tires are cold, and conduct
initialization again.
●While the position of each tire is being
determined and the inflation pressures are not being displayed on the multi-information display, if the inflation pres-
sure of a tire drops, the tire pressure warning light will come on.
■When initialization of the tire pressure warning system has failed
Initialization may take longer to complete if
the vehicle is driven on an unpaved road. When performing initialization, drive on a paved road if possible. Depending on the
driving environment an d condition of the tires, initialization will be completed in approximately 10 to 30 minutes. If initializa-
tion is not complete after driving approxi- mately 10 to 30 minutes, continue driving for a while. If the inflation of each tire is not
displayed after driving for approximately 1 hour, perform the following procedure.
●Park the vehicle in a safe place for approximately 20 minutes. Then drive straight (with occasional left and right
turns) at approximately 40 km/h (25 mph) or more for approximately 10 to 30 minutes.
However, in the following situations, the tire
inflation pressure will not be recorded and
the system will not operate properly. Per-
form initialization again.
●When performing init ialization, the tire

337
6
-$@-$I@0.@0.&@ &&

6-3. Do-it-yourself maintenance
Maintenance and care
pressure warning light does not blink 3 times. (Initialization will not occur while driving)
●After performing init ialization, the tire pressure warning light blinks for 1 minute
then stays on after driving for about 20 minutes.
If the inflation pressure of each tire is still not
displayed, have the vehicle inspected by
any authorized Lexus retailer or Lexus
authorized repairer, or any reliable repairer.
■When registering ID codes
●Initialize the tire pressure warning system after ID code registra tion. Initialization is
disabled if the system was initialized before registration.
●After ID code registration, the tires are hot by driving. Initia lize the tire pressure warning system after the tires become
cold.
The tire pressure warning valve and
transmitter is equipped with a unique
ID code. When replacing a tire pres-
sure warning valve and transmitter, it is
necessary to register the ID code.
When registering the ID codes, per-
form the following procedure.
1 Turn the engine switch switch> to IGNITION ON mode
.
2 Press or of the meter con-
trol switches and select .
3 Press or of the meter con-
trol switches and select “Vehicle
Settings”, and then press “OK”.
4 Press or of the meter con-
trol switches and select “TPWS
SET”, and then press “OK”.
5 Press or of the meter con-
trol switches and select “Change
wheel set”, and then press and hold
“OK” until the tire pressure warning
light starts blinking.
The change wheel set mode is activated and registration is started.
A message is displayed on the multi-infor- mation display, and “--” is displayed for inflation pressure of e ach tire. Then, the tire
pressure warning light blinks rapidly for approximately 1 minute and stays on.
6 Drive the vehicle at 40 km/h
(25mph) or more for approxi-
mately 10 to 30 minutes.
When registration is completed, the tire pressure warning light will go off and the inflation pressure of each tire will be dis-
played on the multi-information display.
WARNING
■When initializing the tire pressure
warning system
Do not initialize tire inflation pressure
without first adjusting the tire inflation pressure to the specified level. Other-wise, the tire pressure warning light may
not come on even if the tire inflation pres- sure is low, or it may come on when the tire inflation pressure is actually normal.
Registering ID codes

338
-$@-$I@0.@0.&@ &&

6-3. Do-it-yourself maintenance
The time elapsed before registration is completed differs according to the driving condition and environment.
■Canceling the change wheel set mode
●If turning the engine switch off when in the change wheel set
mode before driving, the change wheel set mode is canceled.
●After driving when in the change wheel set mode, the change wheel set mode cannot be canceled. To cancel the mode,
perform the procedure for ID code regis- tration again and turn the engine switch off before driving.
●If the change wheel set mode is canceled, the ID codes that have already been reg-
istered are communicated. When com- munication is finished, the tire pressure warning light will turn off.
■When ID code registration may not
operate properly
●Do not move the vehicle backward
during registration. Registration is started again from the beginning and it may take longer than usual.
●When another vehicle is running the side of the vehicle such as in heavy traffic, it
may take longer to detect the vehicle’s tire pressure warning valves and trans-mitters.
●If tire pressure warning valves and trans-mitters are in the vehicle, the ID codes
may not be registered.
If registration takes long time, perform the
procedure for ID code registration again
after parking the vehicle for 20 minutes.
If the ID codes cannot be registered even
when performing the above procedure,
contact any authorized Lexus retailer or
Lexus authorized repairer, or any reliable
repairer.

339
6
-$@-$I@0.@0.&@ &&

6-3. Do-it-yourself maintenance
Maintenance and care
Stop the vehicle in a safe place on a
hard, flat surface.
 Set the parking brake.
 Shift the shift position to P.
 Turn off the intrusion sensor and tilt
sensor ( P.78)
 Stop the engine .
Screwdriver
Wheel nut wrench
Jack
Jack handle
Towing eyelet
Replacing the tire
When raising your vehicle with a
jack, position the jack correctly.
Improper placement may damage
your vehicle or cause injury.
If necessary tire replacement
seems difficult to perform, contact
any authorized Lexus retailer or
Lexus authorized repairer, or any
reliable repairer.
Before jacking up the vehicle
Location of the jack and tools
A
B
C
D
E

340
-$@-$I@0.@0.&@ &&

6-3. Do-it-yourself maintenance
1Pull the strap up and remove the
rear luggage mat.
2 Take out the jack.
Remove the jack handle, and then take out the jack.
1 Chock the tires.
WARNING
■Using the tire jack
Observe the following precautions.
Improper use of the tire jack may cause the vehicle to suddenly fall off the jack, leading to death or serious injury.
●Do not use the tire jack for any pur-
pose other than replacing tires.
●Only use the tire jack that comes with this vehicle for replacing a tire. Do not use it on other vehicles, and do
not use other tire jacks for replacing tires on this vehicle.
●Put the jack properly in its jack point.
●Do not put any part of your body under the vehicle while it is supported by the
jack.
●Do not start the engine or drive the vehicle while the vehicle is supported by the jack.
●Do not raise the vehicle while some-
one is inside.
●When raising the vehicle, do not put an object on or under the jack.
●Do not raise the vehicle to a height greater than that required to replace
the tire.
●Use a jack stand if it is necessary to get under the vehicle.
●When lowering the vehicle, make sure that there is no-one near the vehicle. If
there are people nearby, warn them vocally before lowering.
Taking out the jack
Removing a tire

341
6
-$@-$I@0.@0.&@ &&

6-3. Do-it-yourself maintenance
Maintenance and care
2Slightly loosen the wheel nuts (one
turn).
3 Turn the tire jack portion by
hand until the notch of the jack is in
contact with the jack point.
The jack point guides are located under the rocker panel. They indicate the jack
point positions.
4 Raise the vehicle until the tire is
slightly raised off the ground.
5 Remove all the wheel nuts and the
tire.
When resting the tire on the ground, place
the tire so that the wheel design faces up to avoid scratching the wheel surface.
1 Remove any dirt or foreign matter
from the wheel contact surface.
TireWheel chock positions
Front left-
hand side
Behind the rear right-hand
side tire
Front right-
hand side
Behind the rear left-hand
side tire
Rear left-
hand side
In front of the front right-
hand side tire
Rear right-
hand side
In front of the front left-hand
side tire
A
WARNING
■Replacing a tire
Do not touch the disc wheels or the area around the brakes immediately after the vehicle has been driven.
After the vehicle has been driven the disc wheels and the area around the brakes will be extremely hot. Touching these
areas with hands, feet or other body parts while changing a tire, etc. may result in burns.
Installing the tire

342
-$@-$I@0.@0.&@ &&

6-3. Do-it-yourself maintenance
If foreign matter is on the wheel contact surface, the wheel nuts may loosen while the vehicle is in motion, causing the tire to
come off.
2 Install the tire and loosely tighten
each wheel nut by hand by approxi-
mately the same amount.
Turn the wheel nuts until the washers come
into contact with the disc wheel.
Disc wheel
Washer
3 Lower the vehicle.
4 Firmly tighten each wheel nut two
or three times in the order shown in
the illustration.
Tightening torque: 140 N•m (14.3 kgf•m, 103.3 ft•lbf)
5 Stow the jack and all tools.
A
B

343
6
-$@-$I@0.@0.&@ &&

6-3. Do-it-yourself maintenance
Maintenance and care
■Certification for the jack

344
-$@-$I@0.@0.&@ &&

6-3. Do-it-yourself maintenance
WARNING
■When installing the tire
Failure to follow these precautions could cause the wheel nuts to loosen and the tire to fall off, resulting in death or serious
injury.
●Never use oil or grease on the wheel bolts or wheel nuts.Oil and grease may cause the wheel
nuts to be excessively tightened, lead- ing to bolt or disc wheel damage. In addition, the oil or grease can cause
the wheel nuts to loosen and the wheel may fall off, causing a serious accident. Remove any oil or grease from the
wheel bolts or wheel nuts.
●Have the wheel nuts tightened with a torque wrench to 140 N•m (14.3 kgf•m, 103.3 ft•lbf) as soon as possible
after changing wheels.
●Do not attach a heavily damaged wheel ornament, as it may fly off the wheel while the vehicle is moving.
●When installing a ti re, only use wheel
nuts that have been specifically designed for that wheel.
●If there are any cracks or deformations in the bolt screws, nut threads or bolt
holes of the wheel, have the vehicle inspected by any authorized Lexus retailer or Lexus authorized repairer,
or any reliable repairer.
■After using the tools and jack
Before driving, make sure all the tools and jack are stored securely in place. Failure to do so may cause injury in case
of a collision or sudden braking.
NOTICE
■Repairing or replacing tires, wheels, tire pressure warning valves, trans-mitters and tire valve caps
 P.335

345
6
-$@-$I@0.@0.&@ &&

6-3. Do-it-yourself maintenance
Maintenance and care
■Effects of incorrect tire inflation pres- sure
Driving with incorrect tire inflation pressure may result in the following:
●Reduced fuel economy
●Reduced driving comfort and poor han-dling
●Reduced tire life due to wear
●Reduced safety
●Damage to the drivetrain
If a tire needs frequent inflating, have it checked by any authorized Lexus retailer or Lexus authorized repairer, or any reliable
repairer.
■Instructions for checking tire inflation pressure
When checking tire inflation pressure, observe the following:
●Check only when the tires are cold.If your vehicle has been parked for at least 3 hours or has not been driven for
more than 1.5 km or 1 mile, you will get an accurate cold tire inflation pressure read-ing.
●Always use a tire pressure gauge.It is difficult to judge if a tire is properly
inflated based only on its appearance.
●It is normal for the tire inflation pressure
to be higher after driving as heat is gen- erated in the tire. Do not reduce tire infla-tion pressure after driving.
●Passengers and luggage weight should be placed so that the vehicle is balanced.
Tire inflation pressure
Make sure to maintain proper tire
inflation pressure. Tire inflation
pressure should be checked at least
once per month. However, Lexus
recommends that tire inflation
pressure be checked once every
two weeks.
WARNING
■Proper inflation is critical to save tire performance
Keep your tires properly inflated. If the tires are not properly inflated, the following conditions may occur which
could lead to an accident resulting in death or serious injury:
●Excessive wear
●Uneven wear
●Poor handling
●Possibility of blowouts resulting from overheated tires
●Air leaking from between tire and
wheel
●Wheel deformation and/or tire dam- age
●Greater possibility of tire damage while driving (due to road hazards,
expansion joints, sh arp edges in the road, etc.)
NOTICE
■When inspecting and adjusting tire inflation pressure
Be sure to put the tire valve caps back on. If a valve cap is not installed, dirt or mois-
ture may get into the valve and cause an air leak, resulting in decreased tire infla-tion pressure.