lock lexus LC500 2018 Manual PDF

224
-$@-$I@0.@0.&@ &&

4-5. Using the driving support systems
●The vehicle is driven on a surface that is bright due to reflected light, etc.
●The vehicle is driven in an area where the brightness changes suddenly, such as at the entrances and exits of tunnels, etc.
●Light from the headlights of an oncoming vehicle, the sun, etc. enters the camera.
●The vehicle is driven where the road diverges, merges, etc.
●The vehicle is driven on a slope.
●The vehicle is driven on a road which tilts left or right, or a winding road.
●The vehicle is driven on an unpaved or rough road.
●The vehicle is driven around a sharp curve.
●The traffic lane is excessively narrow or wide.
●The vehicle is extremely tilted due to car-rying heavy luggage or having improper tire pressure.
●The distance to the preceding vehicle is extremely short.
●The vehicle is moving up and down a
large amount due to road conditions during driving (poor roads or road seams).
●The headlight lenses are dirty and emit a faint amount of light at night, or the beam
axis has deviated.
●The vehicle is struck by a crosswind.
●The vehicle has just changed lanes or crossed an intersection.
●Snow tires, etc. are equipped.
■Warning message
If the following warning message is dis- played on the multi-information display and the LKA indicator illuminates in orange, fol-
low the appropriate troubleshooting proce- dure.
Warning mes-
sageDetails/Actions
“Lane Keep-
ing Assist
Malfunction
Visit Your
Dealer”
The system may not be
operating properly.
 Have the vehicle
inspected any authorized
Lexus retailer or Lexus
authorized repairer, or
any reliable repairer.
“Front Cam-
era Vision
Blocked
Clean and
Demist Wind-
shield”
Dirt, rain, condensation,
ice, snow, etc. are present
on the windshield in front
of the camera sensor.
 Turn the LKA system
off, remove any dirt, rain,
condensation, ice, snow,
etc. from the windshield,
and then turn the LKA sys-
tem back on.
“Front Cam-
era Unavail-
able”
The operation conditions
of the camera sensor
(temperature, etc.) are
not met.
 When the operation
conditions of the camera
sensor (temperature, etc.)
are met, the LKA system
will become available.
Turn the LKA system off,
wait for a little while, and
then turn the LKA system
back on.

262
-$@-$I@0.@0.&@ &&

4-5. Using the driving support systems
■ECB (Electronically Controlled
Brake System)
The electronically controlled system
generates braking force correspond-
ing to the brake operation
■ABS (Anti-lock Brake System)
Helps to prevent wheel lock when the
brakes are applied suddenly, or if the
brakes are applied while driving on a
slippery road surface
■Brake assist
Generates an increased level of brak-
ing force after the brake pedal is
depressed when the system detects a
panic stop situation
■VSC (Vehicle Stability Control)
Helps the driver to control skidding
when swerving suddenly or turning on
slippery road surfaces
■Secondary Collision Brake (if
equipped)
When the airbag sensor detects a colli-
sion, the brakes and brake lights are
automatically controlled to reduce the
vehicle speed and that helps reduce
the possibility of further damage due to
a secondary collision.
■TRC (Traction Control)
Helps to maintain drive power and pre-
vent the drive wheels from spinning
when starting the vehicle or accelerat-
ing on slippery roads
■Hill-start assist control
Helps to reduce the backward move-
ment of the vehicle when starting on an
uphill
■VGRS (Variable Gear Ratio Steer-
ing) (if equipped)
Adjusts the front wheel turning angle in
accordance with the vehicle speed and
steering wheel movement
■DRS (Dynamic Rear Steering) (if
equipped)
Contributes to the turning characteris-
tics and responsiveness of the vehicle
by slightly adjusting the rear wheel
angle of the vehicle in accordance with
steering wheel movement.
■EPS (Electric Power Steering)
Employs an electric motor to reduce
the amount of effort needed to turn the
steering wheel
■AVS (Adaptive Variable Suspen-
sion System)
By independently controlling the
damping force of the shock absorbers
for each of the 4 wheels according to
Driving assist systems
To keep driving safety and perfor-
mance, the following systems oper-
ate automatically in response to
various driving situations. Be aware,
however, that these systems are
supplementary and should not be
relied upon too heavily when oper-
ating the vehicle.
Summary of the driving assist
systems

270
-$@-$I@0.@0.&@ &&

4-6. Driving tips
Perform the following according to the
driving conditions:
 Do not try to forcibly open a window
or move a wiper that is frozen. Pour
warm water over the frozen area to
melt the ice. Wipe away the water
immediately to prevent it from
freezing.
 When the outside door handle is
frozen, unlock the doors using the
wireless remote control. If the out-
side door handles remain retracted
and do not move even if the doors
are unlocked using the wireless
remote control, pour warm water
over the frozen area to melt the ice
and wipe away the water immedi-
ately to prevent it from freezing. The
outside door handle may not retract
due to ice, however, the outside
door handle will return to the nor-
mal position after the ice melts.
 To ensure proper operation of the
climate control system fan, remove
any snow that has accumulated on
the air inlet vents in front of the
windshield.
 Check for and remove any excess
ice or snow that may have accumu-
lated on the exterior lights, vehicle’s
roof, chassis, around the tires or on
the brakes.
 Remove any snow or mud from the
bottom of your shoes before getting
in the vehicle.
■To protect windshield wipers
 P.198
Accelerate the vehicle slowly, keep a
safe distance between you and the
vehicle ahead, and drive at a reduced
speed suitable to road conditions.
Park the vehicle and shift the shift posi-
tion to P without setting the parking
brake. The parking brake may freeze
up, preventing it from being released. If
the vehicle is parked without setting
the parking brake, make sure to block
the wheels.
Failure to do so may be dangerous
because it may cause the vehicle to
move unexpectedly, possibly leading to
an accident.
NOTICE
■Repairing or replacing snow tires
Request repairs or re placement of snow
tires from any authorized Lexus retailer or Lexus authorized repairer, or any reli-able repairer.
This is because the removal and attach- ment of snow tires affects the operation
of the tire pressure warning valves and transmitters.
Before driving the vehicle
When driving the vehicle
When parking the vehicle

282
-$@-$I@0.@0.&@ &&

5-3. Using the air conditioning system
perature setting or the inside temperature.
■Registering air conditioning settings to electronic keys
●Unlocking the vehicle using an electronic key and turning the engine switch switch> to IGNITION ON mode will recall that key’s registered air conditioning settings.
●When the engine switch is turned off, the current air conditioning
settings will automatically be registered to the electronic key that was used to unlock the vehicle.
●The system may not operate correctly if more than one electronic key is in the
vicinity or if the smart entry & start system is used to unlock the passenger door.
●The doors that can recall the air condi-
tioning setting* when unlocked using the
smart entry & start system can be changed. For details, contact any autho-rized Lexus retailer or Lexus authorized
repairer, or any reliable repairer.*: The doors that can recall the driving posi-
tion memory are changed at the same
time.
■Operation of the air conditioning sys- tem in Eco drive mode
In Eco drive mode, the air conditioning sys- tem is controlled as follows to prioritize fuel
efficiency:
●Engine speed and compressor operation
controlled to restrict heating/cooling capacity
●Fan speed restricted when automatic mode is selected
To improve air conditioning performance, perform the following operations:
●Adjust the fan speed
●Turn off Eco drive mode ( P.242)
■When the outside temperature falls to
nearly 0°C (32°F)
The dehumidification function may not
operate even when “A/C” is selected.
■Ventilation and air conditioning odors
●To let fresh air in, set the air conditioning
system to the outside air mode.
●During use, various odors from inside and
outside the vehicle may enter into and accumulate in the air conditioning sys-tem. This may then cause odor to be
emitted from the vents.
●To reduce potential odors from occur-
ring: • It is recommended that the air condition-ing system be set to outside air mode
prior to turning the vehicle off. • The start timing of the blower may be delayed for a short period of time imme-
diately after the air conditioning system is started in automatic mode.
●When parking, the system automatically switches to fresh air intake mode to encourage better air circulation through-
out the vehicle, helping to reduce odors that occur when starting the vehicle.
■Air conditioning filter
 P.347
■Customization
Settings (e.g. A/C auto switch operation) can be changed.(Customizable features P.423)
WARNING
■To prevent the windshield from fog- ging up
Do not use the windshield defogger switch during cool air operation in extremely humid weather. The difference
between the temperature of the outside air and that of the windshield can cause the outer surface of the windshield to fog
up, blocking your vision.
■When the outside rear view mirror defoggers are operating
Do not touch the outside rear view mir- ror surfaces, as they can become very hot and burn you.

291
5
-$@-$I@0.@0.&@ &&

5-4. Using the interior lights
Interior features
5 -4. Us in g the i n te rior li gh ts
Outside door handle lights
Personal lights ( P.292)
Seat lights
Shift lever light
Door trim ornament lights
Door courtesy lights
Footwell lights
■Personal lights automatic on/off
●Illuminated entry system: The lights auto- matically turn on/off according to the
engine switch mode, the presence of the electronic key, whether the doors are locked/unlocked, and
whether the doors are opened/closed.
●If the personal lights remain on when the
engine switch is turned
off, the lights will go off automatically
after 20 minutes.
■When personal lights do not respond as normal
●When water, dirt, etc., have adhered to the lens surface
●When operated with a wet hand
●When wearing gloves, etc.
Interior lights list
Location of the interior lights
A
B
C
D
E
F
G

293
5
-$@-$I@0.@0.&@ &&

5-5. Using the storage features
Interior features
5-5.Using the storage features
Glove box (P.293)
Auxiliary net
Door pockets
Console box/auxiliary box
( P.294)
Cup holder ( P.294)
1 Open (press the glove box opener)
2 Unlock with the mechanical key
3 Lock with the mechanical key
■Glove box light
The glove box light turns on when the tail lights are on.
■Trunk opener main switch
 P.122
■If the 12-volt battery is discharged
The glove box cannot be opened as usual.
Refer to P.393 to open the glove box.
List of stor age features
Location of the storage features
WARNING
■Items that should not be left in the
vehicle
Do not leave glasses, lighters or spray cans in the storage spaces, as this may cause the following when cabin tempera-
ture becomes high:
●Glasses may be deformed by heat or cracked if they come into contact with other stored items.
A
B
C
D
E
●Lighters or spray cans may explode. If they come into contact with other
stored items, the lighter may catch fire or the spray can may release gas, causing a fire hazard.
■When the storage compartments are
not in use
When driving or when the storage com- partments are not in use, keep the lids closed.
In the event of sudden braking or sudden swerving, an accident may occur due to an occupant being struck by an open lid
or the items stored inside.
Glove box

297
5
-$@-$I@0.@0.&@ &&

5-6. Using the other interior features
Interior features
5-6.Using the other interior features
1To set the visor in the forward posi-
tion, flip it down.
2 To set the visor in the side position,
flip down, unhook, and swing it to
the side.
Open the cover.
The light turns on when the cover is
opened.
The GPS clock’s time is automatically
adjusted by utilizing GPS time infor-
mation.
For details, refer to the “NAVIGA-
TION SYSTEM OWNER’S MAN-
UAL”.
Please use as a power supply for elec-
tronic goods that use less than 12
VDC/10 A (power consumption of
120 W).
Open the lid.
■The power outlet can be used when
The engine switch

is in ACCESSORY or IGNITION ON mode
.
Other interior features
Sun visors
Vanity mirrors
NOTICE
■To prevent 12-volt battery discharge
Do not leave the lights on longer than necessary when the engine tem> is off.
Clock
Power outlet

305
6
-$@-$I@0.@0.&@ &&

6-1. Maintenance and care
Maintenance and care
■Notes for a smart entry & start system
If the door handle becomes wet while the
electronic key is within the effective range, the door may lock and unlock repeatedly. In that case, follow the following correction
procedures to wash the vehicle:
●Place the key in a position 2 m (6 ft.) or
more separate from the vehicle while the vehicle is being washed. (Take care to ensure that the key is not stolen.)
●Set the electronic key to battery-saving mode to disable the smart entry & start
system. ( P.124)
■Aluminum wheels
●Remove any dirt immediately by using a
neutral detergent.
●Wash detergent off with water immedi-
ately after use.
●To protect the paint from damage, make
sure to observe the following precau- tions.• Do not use acidic, alkaline or abrasive
detergent • Do not use hard brushes• Do not use detergent on the wheels when
they are hot, such as after driving or park- ing in hot weather
■Brake caliper coating
●When using detergent, use neutral deter-gent. Do not use hard brushes or abra-
sive cleaners, as they will damage the coating.
●Do not use detergent on the brake cali-pers when they are hot.
●Wash detergent off immediately after use.
■Bumpers
Do not scrub with abrasive cleaners.
■Front side windows water-repellent coating
●The following precautions can extend the effectiveness of the water-repellent coat-ing.
• Remove any dirt, etc. from the front side windows regularly.• Do not allow dirt and dust to accumulate
on the windows for a long period. Clean the windows with a soft, damp cloth as soon as possible.
• Do not use wax or glass cleaners that contain abrasives when cleaning the win-dows.
• Do not use any metallic objects to remove condensation build up.
●When the water-repellent performance has become insufficient, the coating can be repaired. Contact any authorized
Lexus retailer or Lexus authorized repairer, or any reliable repairer.
WARNING
■When washing the vehicle
Do not apply water to the inside of the
engine compartment. Doing so may cause the electrical components etc. to catch fire.
■When cleaning the windshield
Set the wiper switch to off. If the wiper switch is in AUTO, the wipers
may operate unexpectedly in the follow- ing situations, and may result in hands being caught or other serious injuries
and cause damage to the wiper blades.
Off
AUTO
●When the upper part of the windshield where the raindrop sensor is located is
touched by hand
●When a wet rag or similar is held close to the raindrop sensor
●If something bumps against the wind-shield
A
B

316
-$@-$I@0.@0.&@ &&

6-3. Do-it-yourself maintenance
1Pull the hood lock release lever.
The hood will pop up slightly.
2Pull up the auxiliary catch lever and
lift the hood.
■Front
Hood
Opening the hood
WARNING
■Pre-driving check
Check that the hood is fully closed and locked.
If the hood is not locked properly, it may open while the vehicle is in motion and cause an accident, which may result in
death or serious injury.
Positioning a floor jack
When using a floor jack, follow the
instructions in the manual provided
with the jack and perform the oper-
ation safely.
When raising your vehicle with a
floor jack, position the jack cor-
rectly. Improper placement may
damage your vehicle or cause
injury.
Location of the jack point

321
6
-$@-$I@0.@0.&@ &&

6-3. Do-it-yourself maintenance
Maintenance and care
LC500
LC500h
1 Remove the oil filler cap by turning
it counterclockwise.
2 Add engine oil slowly, checking the
dipstick.
3 Install the oil filler cap by turning it
clockwise.
■Engine oil consumption
A certain amount of engine oil will be con-
sumed while driving. In the following situa- tions, oil consumption may increase, and engine oil may need to be refilled in
between oil maintenance intervals.
●When the engine is new, for example
directly after purchasing the vehicle or after replacing the engine
●If low quality oil or oil of an inappropriate viscosity is used
●When driving at high engine speeds or with a heavy load, or when driving while accelerating or decelerating frequently
●When leaving the engine idling for a long time, or when driving frequently through heavy traffic
■After changing the engine oil (LC500h)
The engine oil maintenance data should be reset. Perform the following procedures:
1 While the vehicle is stopped, press
of the meter control switches.
2 Press or of the meter control
switches, and select .
3 Press or of the meter control
switches, select “Vehicle Settings”, and
then press “OK”.
4 Press or of the meter control
switches, select “Oil Maintenance”, and
then press “OK”.
5 Select “Yes” and then press “OK”.
A message will be displayed on the multi- information display.
WARNING
■Used engine oil
●Used engine oil contains potentially harmful contaminants which may cause skin disorders such as inflamma-
tion and skin cancer, so care should be taken to avoid prolonged and repeated contact. To remove used
engine oil from your skin, wash thor- oughly with soap and water.