seat lexus LS400 1998 Audio System / LEXUS 1998 LS400 (OM50498U) Workshop Manual

COMFORT ADJUSTMENT
108
16L1681
CAUTION
Push and pull the child restraint system in different directions
to be sure it is secure. Follow all the installation instructions
provided by its manufacturer.
16L1691
4. To remove the convertible seat, press the bucklerelease button
and allow the belt to retract completely. The belt will move freely
again and be ready to work for an adult or older child passenger.

COMFORT ADJUSTMENT
109 (C) Booster seat installation
16L1594
A booster seat is used in forwardfacing position only.
16L152
Move seat fully back
CAUTION
A forwardfacing child restraint system should be put on the
front seat only when it is unavoidable. Always move the seat
as far back as possible, because the force of a deploying airbag
could cause death or serious injury to the child. Do not allow
the child to lean over the front door or around the front door
even if the child is seated in a child restraint system. It is
dangerous if the side airbag inflates, and the impact could
cause death or serious injury to the child.

COMFORT ADJUSTMENT
110
16L1702
1. Sit the child on a booster seat. Run the lap and shoulder belt
through or around the booster seat and child following the
instructions provided by its manufacturer and insert the tab into the
buckle.
Make sure the shoulder belt is correctly across the child’s shoulder
and that the lap belt is positioned as low as possible on child’s hips.
See ”Seat belts” on page 80 for details.
CAUTION
Always make sure the shoulder belt is positioned across the
center of child’s shoulder. The belt should be kept away
from child’s neck, but not falling off child’s shoulder.
Failure to do so could reduce the amount of protection in an
accident and cause serious injuries in a collision.
Highpositioned lap belts and loosefitting belts both could
cause serious injuries due to sliding under the lap belt
during a collision or other unintended result. Keep the lap
belt positioned as low on hip as possible.
For child’s safety, do not place the shoulder belt under
child’s arm.
After inserting the tab, make sure the tab and buckle are
locked and that the lap and shoulder portions of the belt are
not twisted.
Do not insert coins, clips, etc. in the buckle as this may
prevent you from properly latching the tab and buckle.
If the seat belt does not function normally, immediately
contact your Lexus dealer. Do not use the seat until the seat
belt is fixed. It cannot protect your child from injury.

COMFORT ADJUSTMENT
113
16L0401
1
Bolt 2
Anchor bracket 3
Spacer
4. Insert a 15 mm (0.6 in.) spacer, and tighten down the anchor
bracket for your child restraint system with a bolt. Torque the bolt
to 16.5 24.7 N·m (1.68 2.52 kgf·m, 12.2 18.2 ft·lbf.).
To comply with Canada Motor Vehicle Safety Standards, vehicles
sold in Canada are provided with a bracket set in the glovebox.
DRIVING POSITION MEMORY
SYSTEM
The micro computer can memorize the position of the driver’s seat,
the height of the shoulder belt anchor of the driver’s seat belt, and the
positions of the tilt and telescopic steering, and outside rear view
mirrors. Two different driving position profiles can be entered into
the computer’s memory.
Recording a driving position in the computer’s memory can only be
done when the ignition key is in the ”ON” position and the shift lever
is in the ”P” position.
Setting a driving position
16L055
1. Adjust the driver’s seat, driver’s shoulder belt anchor, tilt and
telescopic steering and outside rear view mirrors to the desired
position.
2. While pushing the ”SET” button, push button ”1” or ”2” until
the signal beeps.

COMFORT ADJUSTMENT
114The beep sound means that the positions are recorded in the
computer ’s memory.
By repeating these two steps and pressing the remaining button, the
driving position for another driver can be recorded.
To set a new memorized position, select the desired position and
perform step 2. The previous memory will be erased and the new
position will be set.
To make only slight changes to an already memorized position, the
easiest way is to first activate the memorized position, then make the
desired changes and perform step 2 above.
Activating a memorized position
16L056
When you push button ”1” or ”2”, the driving position will be
automatically adjusted to the position recorded for that button.Conditions for memorized position activation
Ignition key ”ON” and shift lever in ”P” position.
All parts of the memorized positions can be activated.
However, if the brake pedal is being depressed, the seat position
will not change.
Key not in ignition switch and within 30 seconds of opening
driver’s door.
The memorized position can be activated, except for the tilt and
telescopic steering.
If any driving position memory switch is pushed while one of the
memorized driving position profiles is being activated, the operation
will stop.
To activate the system, push the desired button (”1” or ”2”) again.
The driving position memory control system cannot be operated
while the vehicle is moving.
If the vehicle’s battery is disconnected, the computer’s memory will
be erased and the memorized positions will have to be set again.
CAUTION
Do not start the vehicle while the adjustments are being
made.
Take care not to select the wrong button, or the seat could
strike the rear passenger or hit your body against the
steering wheel. If this happens, you can stop the movement
by pressing another driving position memory switch, or
depressing the brake pedal.

STARTING AND DRIVING
157
BEFORE STARTING THE ENGINE
1. Check the area around the vehicle before entering it.
2. Adjust seat position, seatback angle, head restraint height and
steering wheel angle.
3. Adjust inside and outside rear view mirrors.
4. Lock all doors.
5. Fasten seat belts.
Remember to check that the service reminder indicators function
when turning the key to ”ON”, and check the fuel gauge to see that
you have sufficient fuel.
IGNITION SWITCH WITH
STEERING LOCK
31L0011
”START” Starter motor on. The key will return to the ”ON”
position when released.
For starting tips, see page 159.
”ON” Engine on and all accessories on.
This is the normal driving position.
NOTICE
Do not leave the key in the ”ON” position if the engine is not
running. The battery will discharge and the electronic ignition
system/distributor ignition system could be damaged.
”ACC” Accessories such as the radio operate, but the engine
is off.
If you leave the key in the ”ACC” or ”LOCK” position and open the

MAINTENANCE
215 Tire rotation
Rotate the tires every 12000 km (7500 miles). See page 242 for
additional information.
Fluid leaks
Check underneath for leaking fuel, oil, water or other fluid after the
vehicle has been parked for a while. If you smell fuel fumes or notice
any leak, have the cause found and corrected immediately.
Doors and engine hood
Check that all doors, including trunk lid, operate smoothly and all
latches lock securely. Make sure the engine hood secondary latch
secures the hood when the primary latch is released.
Vehicle interior
Items listed below should be checked regularly, e.g. while
performing periodic services, cleaning the vehicle, etc.
Lights
Make sure the headlights, stop lights, tail lights, turn signal lights,
and other lights are working. Check headlight aim.
Service reminder indicators and warning buzzers
Check that all service reminder indicators and warning buzzers
function properly.Steering wheel
Check that it has the specified freeplay. Be alert for changes in
steering condition, such as hard steering, excessive freeplay or
strange noise.
Seats
Check that all front seat controls such as seat adjusters, seatback
recliner, etc. operate smoothly. Check that the head restraints move
up and down smoothly and that the locks hold securely in any latched
position.
Seat belts
Check that the seat belt system such as buckles, retractors and
anchors operate properly and smoothly. Make sure the belt webbing
is not cut, frayed, worn or damaged.
Accelerator pedal
Check the pedal for smooth operation and uneven pedal effort or
catching.
Brake pedal
Check the pedal for smooth operation and the proper clearance and
freeplay. Check the brake booster function.
Brakes
At a safe place, check that the brakes do not pull to one side when
applied.

ELECTRICAL COMPONENTS
251
No.FUSEAMPERECIRCUIT
1 TURN7.5Turn signal lights
2 WIPER20Windshield wipers
3 HEATER10
Air conditioning system,
Rear window defogger, Multiport
fuel injection system/sequential
multiport fuel injection system
4 FR FOG15Fog lights
5 ECUIG10Power steering control system,
Charging system,
Vehicle skid control system
6 PWRIG15
Automatic headlight leveling
system, Moon roof,
Headlight cleaner,
Power seat switch,
Tilt and telescopic steering, Shift
lock system
7 GAUGE10
Gauges and meters, service
reminder indicators and warning
buzzers,
Backup lights,
Vehicle skid control system,
Multiport fuel injection
system/sequential multiport fuel
injection system, Automatic
transmission system
8 IGN10SRS, Multiport fuel injection
system/sequential multiport fuel
injection system
9 RR FOG7.5No circuit
10 FUEL OPN10Fuel opener system
No.FUSEAMPERECIRCUIT
11 RR CIG15Rear cigarette lighter,
Power outlet
12 FR CIG15Front cigarette lighter, SRS
13 A/C7.5Air conditioning system
14 P RR
DOOR20Rear door lock,
Rear power window
15 STOP LP25Stop lights,
High mounted stop light
16 RADIO
NO.215
Audio system,
Outside rear view mirror,
Shift lock system,
Air conditioning system
17 PANEL7.5Instrument panel lights,
Air conditioning system, Glovebox
light, Audio system
18 STARTER7.5
Starting system,
Automatic transmission system,
Multiport fuel injection
system/sequential multiport fuel
injection system
19 TAIL7.5Tail lights, Side marker lights,
License plate lights
20 STOPS7.5
Shift lock system,
Height control system, Antilock
brake system,
Vehicle skid control system
21 RR S/HTR15No circuit
22 WASHER20Windshield washer

ELECTRICAL COMPONENTS
252
No.FUSEAMPERECIRCUIT
23 AIR SUS20Height control system
24 D RR
DOOR20Rear door lock,
Rear power window
25 HORN10Horns
26 ETCS15Electronic throttle control system
27 HLP L
UPR10Lefthand headlight (high beam)
28 HLP R
UPR10Righthand headlight (high beam)
29 EFI NO.210Emission control system
30 MIRHTR15Outside rear view mirror defogger
31 FR S/HTR15Seat heater
32 ALTS7.5Charging system
33 TEL15Telephone
34 CRT15Multi information display
35 RADIO
NO.120Audio system
36 MPXB10Power window, Door lock,
Tilt and telescopic steering
37 ECUB7.5Vehicle skid control system,
Daytime running light system
38 HAZ10Emergency flashers
No.FUSEAMPERECIRCUIT
39 EFI NO.120Multiport fuel injection
system/sequential multiport fuel
injection system
40 DOME10Interior light, Vanity lights,
Foot lights, Rear personal light,
Garage door opener
41 OBD7.5Onboard diagnosis system
42 DRL10Vehicles sold in Canada
Daytime running light system
43 HLP R
LW R15Righthand headlight (low beam)
44 HLP L
LW R15Lefthand headlight (low beam)

ELECTRICAL COMPONENTS
261
ADDING WASHER FLUID
64L017
If the washer tank becomes nearly empty, add washer fluid.
You may use plain water as washer fluid. However, in cold areas
where temperatures range below the freezing point, use washer fluid
containing antifreeze. This product is available at your Lexus dealer
and most auto parts stores. Follow the manufacturer’s directions for
how much to mix with water.
NOTICE
Do not use engine antifreeze or any other substitute because it
may damage your vehicle’s paint.
CHECKING THE HEADLIGHT AIM
(Vehicles with discharge headlight only)
64L0732
1
Adjusting bolt (vertical movement)
2
Beam angle gauge and adjusting bolt
(horizontal movement)
Before checking the headlight aim:
1. Be sure that the body around the headlight is not deformed.
2. Park the vehicle on a level spot.
3. The driver gets into the driver’s seat and puts the vehicle in a state
readying for a driving (with a full tank).
4. Bounce the vehicle several times.