engine lexus LS400 2000 Engine / LEXUS 2000 LS400 (OM50533U) Workshop Manual

STARTING AND DRIVING
305
CRUISE CONTROL
The cruise control allows you to cruise the vehicle
at a desired speed over 40 km/h (25 mph) with your
foot off the accelerator pedal.
Your cruising speed can be maintained although a slight
speed change may occur when driving up or down a
gradient, within the limits of engine performance. On
steeper hills, a great speed change will occur so it is
better to drive without the cruise control.
When the cruise control is on, the driving pattern of the
automatic transmission is fixed in the normal position,
regardless of the position of the selector switch.
CAUTION
To help maintain maximum control of your vehicle,
do not use the cruise control when driving in heavy
or varying traffic, or on slippery (rainy, icy or
snow±covered) or winding roads.
 Avoid vehicle speed increases when driving
downhill. If the vehicle speed is too fast in relation to
the cruise control set speed, cancel the cruise
control then downshift the transmission to use
engine braking to slow down.

STARTING AND DRIVING
308
3Resetting to a faster speed
Press the control lever upward in the ºRES/ACCº
direction and hold it. Release the lever when the desired
speed is attained. While the lever is held upward, the
vehicle will gradually gain speed.
When the difference between the actual vehicle speed
and the set speed is less than 5 km/h (3 mph), the set
speed can be increased 1.6 km/h (1 mph) each time by
pressing the control lever upward in the ºRES/ACCº
direction quickly within 0.6 seconds.
However, a quicker way to reset is to accelerate the
vehicle and then press the control lever downward in the
ºSET/COASTº direction. 4 Resetting to a slower speed
Press the control lever downward in the ºSET/COASTº
direction and hold it. Release the lever when the desired
speed is attained. While the lever is held downward, the
vehicle speed will gradually decrease.
When the difference between the actual vehicle speed
and the set speed is less than 5 km/h (3 mph), the set
speed can be lowered 1.6 km/h (1 mph) each time by
pressing the control lever downward in the
ºSET/COASTº direction quickly within 0.6 seconds.
However, a quicker way to reset is to depress the brake
pedal and then press the control lever downward in the
ºSET/COASTº direction.
Even if you downshift the transmission from the ºDº
position to º4º with the cruise control on, engine braking
will not be applied because the cruise control is not
cancelled. To decrease the vehicle speed, reset to a
slower speed with the cruise control lever or depress the
brake pedal. If you use the brake pedal, cruise control
is cancelled.
5 Resuming the preset speed
If the preset speed is cancelled by pulling the control
lever or by depressing the brake pedal, pushing the lever
up in the ºRES/ACCº direction will restore the speed set
prior to cancellation. However, once the vehicle speed
falls below about 40 km/h (25 mph), the preset speed will
not be resumed.

STARTING AND DRIVING
313
31L052±1

Slip indicator light
When you turn the ignition switch on, this system
always turns on. Leave the system on during
ordinary driving so that it can operate when needed.
When traction control is applied, the slip indicator
light blinks.
You may hear a sound in the engine compartment for a
few seconds when the engine is started or just after the
vehicle is started. This means that the traction control
system is in the self ±check mode, and does not indicate
malfunction.
When the traction control system is operating, you may
feel vi bration of your vehicle, caused by operation of the
brakes. This indicates the system is functioning
properly. When getting the vehicle out of mud or new snow, etc.
the traction control system will help operate to prevent
the wheels from spinning.
To turn off the traction control system, see page 317.

STARTING AND DRIVING
315
VEHICLE SKID CONTROLSYSTEM
The vehicle skid control system helps to provide
comprehensive control of the systems such as an
anti±lock brake system, traction control, engine
control, electronically modulated air suspension,
etc. This system automatically controls the output
of the brakes or engine to help prevent the vehicle
from skidding when cornering on a slippery road
surface or abrupt steering wheel operation occurs.
31L052±1

STARTING AND DRIVING
316

Slip indicator light
If the vehicle is going to skid during driving, the slip
indicator light flashes and an alarm sounds.
The vehicle skid control activates when the vehicle
speed is about more than 15 km/h (9 mph).
Depressing the brake pedal repeatedly causes a small
noise from the engine compartment. This is a pump
pulsating sound of the brake system and it is not a
malfunction.
You may hear a sound in the engine compartment for a
few seconds when the engine is started or just after the
vehicle is started. This means that the vehicle skid
control is in the self±check mode and does not indicate
a malfunction.
31L017b

STARTING AND DRIVING
321
BRAKE SYSTEM
The tandem master cylinder brake system is a hydraulic
system with two separate sub±systems. If either
sub±system should fail, the other will still work.
However, the pedal will be harder to press, and your
stopping distance will be longer. Also, the brake system
warning light may come on.
CAUTION
Do not drive your vehicle with only a single brake
system. Have your brakes fixed immediately.
Brake booster
The brake booster uses engine vacuum to power±assist
the brakes. If the engine should quit while you are
driving, you can bring the vehicle to a stop with normal
pedal pressure. There is enough reserved vacuum for
one or two stops but no more!

STARTING AND DRIVING
322
CAUTION
Do not pump the brake pedal if the engine stalls.
Each push on the pedal uses up your reserved
vacuum.
 Even if the power assist is completely lost, the brakes
will still work. But you will have to push the pedal
hard, much harder than normal. And your braking
distance will be longer.
Anti±lock brake system
The anti±lock brake system is designed to help
prevent lock±up of the wheels during a sudden
braking or braking on slippery road surfaces. This
assists in providing stability and steering
performance of the vehicle under these
circumstances.
Effective way to press the ABS brake pedal: When the
anti±lock brake system function is in action, just hold the
brake pedal down more firmly. Especially, in a panic stop,
you need to keep it depressed more firmly, and do not pump
the brake. Pumping the brake pedal makes the stopping dis-
tance longer.

STARTING AND DRIVING
323
The anti±lock brake system becomes operative after the
vehicle has accelerated to a speed in excess of
approximately 10 km/h (6 mph). It stops operating when
the vehicle decelerates to a speed below approximately
5 km/h (3 mph).
Depressing the brake pedal on slippery road surfaces
such as on the manhole cover, the steel plate under the
construction, joints in the bridge, etc. on a rainy day
tends to activate the anti±lock brake system.
You may hear a click or motor sound in the engine
compartment for a few seconds when the engine is
started or just after the vehicle is started. This means
that the anti±lock brake system is in the self±check
mode, and does not indicate a malfunction.
When the anti±lock brake system is activated, the
following conditions may occur, however, do not
indicate a malfunction of the system:

You may hear the anti±lock brake system operating
and feel the brake pedal pulsating and the vibrations
of the vehicle body and steering wheel. You may also
hear the motor sound in the engine compartment
even after the vehicle is stopped.
 At the end of the anti±lock brake system activation,
the brake pedal may move a little to the forward.

STARTING AND DRIVING
327
Drum±in±disc type parking brake system
Your vehicle has a drum±in±disc type parking brake
system. This type of brake system needs
bedding±down of the brake shoes periodically or
whenever the parking brake shoes and/or drums are
replaced.
Have your Lexus dealer perform the bedding±down.
Brake assist system
When you slam the brakes on, the brake assist
system judges as an emergency stop and provides
more powerful braking for a driver who cannot hold
down the brake pedal firmly.
When you slam the brakes on, more powerful braking
will be applied. At this time, you may hear a sound in the
engine compartment and feel the vibrations of the brake
pedal. This does not indicate a malfunction.
The brake assist system becomes operative after the
vehicle has accelerated to a speed in excess of
approximately 10 km/h (6 mph). It stops operating when
the vehicle decelerates to a speed below approximately
5 km/h (3 mph).
For an explanation of this system's warning light, see
ªABSº w arning light on page 68 or 326 and ªV ehicle skid
control failure warningº on page 318.

DRIVING TIPS
332
BREAK±IN PERIOD
Drive gently and avoid high speeds.
You need not follow a break±in schedule with your new
Lexus. But following a few simple tips for the first 1600
km (1000 miles) can add to the future economy and long
life of your vehicle:
Do not drive over 88 km/h (55 mph).
 Avoid overrevving. Maintain engine speed between
2000 and 4000 rpm.
 Avoid full±throttle starts.
 Try to avoid hard stops during the first 300 km (200
miles).
 Do not drive for a long time at any single speed, either
fast or slow.
 Do not tow a trailer during the first 800 km (500 miles).
OPERATION IN FOREIGN
COUNTRIES
If you plan to drive your Lexus in another country ...
First, comply with the vehicle registration laws.
Second, confirm the availability of the correct fuel
(unleaded and minimum octane rating).
TIPS FOR DRIVING IN VARIOUS CONDITIONS
Always slow down in gusty crosswinds. This will
allow you much better control.
 Drive slowly onto curbs and, if possible, at a right
angle. Avoid driving onto high, sharp±edged objects
and other road hazards. Failure to do so can lead to
severe tire damage resulting in tire bursts.
 When parking on a hill, turn the front wheels until they
touch the curb so that the vehicle will not roll. Apply
the parking brake, and place the transmission in ºPº.
If necessary, block the wheels.
 Washing your vehicle or driving through deep water
may get the brakes wet. To see whether they are wet,
check that there is no traffic near you and then press
the pedal lightly. If you do not feel a normal braking
force, the brakes are probably wet. To dry them, drive
the vehicle cautiously while lightly pressing the brake
pedal with the parking brake applied. If they still do
not work safely, pull to the side of the road and call a
Lexus dealer for assistance.
CAUTION
 Before driving off, make sure the parking brake is
fully released and that the parking brake reminder
light is off.
 Do not leave your vehicle unattended while the
engine is running.