rear view mirror LEXUS LS430 2005 User Guide

OCCUPANT RESTRAINT SYSTEMS
223
CAUTION
Do not push the “LOCK” button any longer than 2 or 3
seconds. Pushing the button longer activates an alarm.
For details, see page 40.
Erasing the previous registration memory
The driver’s door must be closed with the ignition switch in the
“OFF” position.
1. Keep the smart key in which you want to cancel the
registration in possession and push the “SET” button.
2. Push the “LOCK” or “UNLOCK” button on the smart
key for about one second with the “SET” button held
down.
When the previous key ID memory is erased, two beeps
sound.MEMORY CALL SYSTEM USING A WIRELESS REMOTE
CONTROL KEY
This system allows you to adjust the driver’s seat, the
driver’s head restraint height, driver’s seat cushion
length, the height of the shoulder belt anchor of the
driver’s seat belt and outside rear view mirrors to the
memorized
position when you open the driver’s door after
unlocking it with a wireless remote control key. And when
you insert the key into the ignition switch, the tilt and
telescopic steering is adjusted.
To activate this system, the ID of the wireless remote
control key ne eds to be registered in the memory button.
Registering the wireless remote control key
ID code
Before the registration of the ID of the wireless remote control
key, the driving position must be memorized in the memory
button.
When registering, the driver’s door must be closed with the
ignition switch in the “OFF” position.
1. Keep the wireless remote control key in possession,
select a button in which you want to record the ID of the
key from buttons “1”, “2” and “3” and push it.
2. Push the “LOCK” or “UNLOCK” button on the wireless
remote control key for about one second with button “1”,
“2” or “3” held down.

SECTION 1 – 7
227
INSTRUMENTS AND CONTROLS150.
Steering wheel and mirrors
Tilt and telescopic steering column228
. . . . . . . . . . . . . . . . . . . . . . . . .
Outside rear view mirrors 230
. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Inside rear view mirror 234
. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Vanity mirrors 235
. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .\
. . . . . .

STEERING WHEEL AND MIRRORS
230
152.OUTSIDE REAR VIEWMIRRORS
16L282
Adjust the mirror so that you can just see the side of your
vehicle in the mirror.
Be careful when judging the size or distance of any object seen
in the outside rear view mirror on the passenger’s side
because it is a convex mirror. Any object seen in a convex
mirror will look smaller and farther away than if seen in a normal
flat mirror.
When the inside rear view mirror darkens in “AUTO” mode, the
outside rear view mirrors also darken to reduce the reflection
of the headlights of the following vehicle. For details, see
“Inside rear view mirror” on page 234. When you push the rear window and outside rear view mirror
defogger swi
tch or operate the wipers, the heater panels in the
outside rear view mirrors will quickly clear the mirror surface.
(See “Windshield wiper and washer switch” on page 58 and
“Rear window and outside rear view mirror defogger switch” on
page 63.)
CAUTION
 Do not adjust the mirror while the vehicle is moving.
Doing so may cause the driver to mishandle the
vehicle and an accident may occur resulting in death
or serious injuries.
 Since the mirror surfaces can get hot, do not touch
them when the rear window and outside rear view
mirror defogger switch is on.

STEERING WHEEL AND MIRRORS
231
Power rear view mirror control153.
16L641
 1Master switch 2Control switch
To adjust the power rear view mirror, first place the master
switch at “L” (left) or “R” (right), and push the contro\
l
switch on the desired side.
The power rear view mirrors can be adjusted when the ignition
switch is in the “ACC” or “ON” position. When you are backing up,
you can adjust the mirrors
down quickly by the following operations with the ignition
ON.
 Put the selector lever in the “R” position.
 Place the master switch at “L” (left) or “R” (right).
The mirrors return to the previous position by any of the
following operations.
 Put the selector lever in a position other than “R”.
 Place the master switch in the neutral position.
 Turn the ignition switch to the “ACC” position.NOTICE
If ice should jam the mirror, do not operate the control
or scrape the mirror face. Use a spray deicer to free the
mirror.

STEERING WHEEL AND MIRRORS
232
Folding and extending automatic rear view
mirrors
16L642
With the rear view mirror folding switch in the “AUTO”
position:
When you turn the ignition switch to “ACC” or “ON” position,
the folded rear view mirrors are automatically extended.
 When you turn the ignition switch to “LOCK” position, the
rear view mirrors are automatically folded.
The rear view mirrors can be folded or extended manually.
CAUTION
 To avoid personal injury and mirror malfunction, do
not touch the mirror while it is moving.
 Do not drive with the mirrors folded backward. Both
the driver and passenger side rear view mirrors must
be extended and properly adjusted before driving.
Folding rear view mirrors154.
16L643
To fold the mirrors, push the switch on the right side. To
extend the rear view mirrors, push the switch on the left
side.
The rear view mirrors can be folded backward for parking in
compact areas.
CAUTION
To avoid personal injury and any mirror malfunction,
do not touch the mirror while it is moving.
 Do not drive with the mirrors folded backward. Both
the driver and passenger side rear view mirrors must
be extended and properly adjusted before driving.

STEERING WHEEL AND MIRRORS
234
156.INSIDE REAR VIEW MIRROR
16L286
Adjust the mirror so that you can just see the rear of your
vehicle in the mirror.
Pushing the switch changes the mode between “AUTO”
and “DAY”.
The indicator comes on when the “AUTO” mode is selected.
“DAY” mode: The mirror surface is normal.
“AUTO” mode: If the mirror detects light from the
headlights of the vehicle behind you, the mirror surface
darkens slightly to reduce the reflected light.
When the inside rear view mirror surface changes, the outside
rear view mirror surfaces will also become darker.
When the ignition switch is turned on, the inside rear view
mirror always turns on in the “AUTO” mode. When the outside air temperature is low, it may take a little
longer for the mirror to darken in response to the detection of
headlights.
CAUTION
Do not adjust the mirror while the vehicle is moving.
Doing so may cause the
driver to mishandle the vehicle
and an accident may occur resulting in death or serious
injuries.

STARTING AND DRIVING
298
BEFORE STARTING THE ENGINE
1. Check the area around the vehicle before entering it.
2. Adjust seat cushion length, seat position, seatback angle,
seat cushion angle, seat cushion height, head restraint height
and steering wheel angle.
3. Adjust the inside and outside rear view mirrors.
4. Lock all doors.
5. Fasten seat belts.
Remember to check that the service reminder indicators
function when turning the ignition switch to “ON”, and check the
fuel gauge to see that you have sufficient fuel.
SMART IGNITION SWITCH WITH STEERING LOCK
31L345a
Carrying a smart key allows you to start the engine
without the key being inserted into the ignition switch.
The smart key system can be deactivated using a key cancel
switch. For details, see “Deactivating the smart key system”
on page 34.

STARTING AND DRIVING
313
(d) Backing up
31L324
 1Brake pedal 2“R” (Reverse) position
1. Bring the vehicle to a complete stop.
2. With the brake pedal held down with your foot, shift the
selector lever to the “R” position.
NOTICE
Never shift into reverse while the vehicle is moving.
When the selector lever is shifted into the “R” position, the
outside rear view mirrors automatically down to help backing
up. For details, see “Power rear view mirror control” on page
231.
Vehicles with rear view monitor system: When the selector
lever is shifted into the “R” position with the ignition switch in\
the “ON” position, rear view monitor system will activate. For
instructions, see “Rear view monitor system” on page 323.

STARTING AND DRIVING
323
REAR VIEW MONITOR SYSTEM
The rear view monitor system assists the driver by
displaying an image of the rear of the vehicle while
backing up. The displayed image on the screen is a
horizontally reversed mirror image of the inside rear view
mirror.
To display the rear view image on the screen, place the
selector lever in the “R” position when the ignition switch
is in the “ON” position.
If you move the selector lever out of the “R” position, the screen
returns to the previous screen. Operating another function of
the navigation system will display another screen.
The rear view monitor system is a supplemental device
intended to assist back up. When backing up, be sure to check
behind and all around the vehicle visually.
CAUTION
 Never depend on the rear view monitor system
entirely when backing up. Always make sure your
intended path is clear.
Use caution just as you would when backing up any
vehicle.
 Never back up while looking only at the screen. The
image on the screen is different from actual
conditions. Depicted distances between objects and
flat surfaces will differ from actual distances. If you
back up while looking only at the screen, you may hit
a vehicle, a person or an object. When backing up, be
sure to check behind and all around the vehicle
visually and with mirrors before proceeding.
 Do not use the system when the trunk is not
completely closed.
 If the back of the vehicle is hit, the position and
mounting angle of the camera may change. Be sure
to have the camera’s position and mounting angle
checked at your Lexus dealer.
 If the temperature changes rapidly , such as when hot
water is poured on the vehicle in cold weather, the
system may not operate normally.

DRIVING TIPS
389
Tires
Ensure that your vehicle’s tires are properly inflated. Adjust
the tire inflation pressure to the recommended cold tire
inflation pressure indicated below:
Tire inflation pressure, kPa (kgf/cm
2 or bar, psi)
P225/55R17 95H Front 220 (2.2, 32) Rear 220 (2.2, 32)
245/45R18 96W Front 230 (2.3, 33) Rear 230 (2.3, 33)
P245/45R18 96V Front 230 (2.3, 33) Rear 230 (2.3, 33)
 The trailer tires should be inflated to the pressure
recommended by the trailer manufacturer in respect to the
total trailer weight.
Trailer lights
 Trailer lights must comply with federal, state/provincial and
local regulations. See your local recreational vehicle dealer
or rental agency for the correct type of wiring and relays for
your trailer. Check for correct operation of the turn signals
and stop lights each time you hitch up. Direct splicing may
damage your vehicle’s electrical system and cause a
malfunction of your lights.
Breakin schedule
 Lexus recommends that you do not tow a trailer with a new
vehicle or a vehicle with any new power train component
(engine, transmission, differential, wheel bearing, etc.) for
the first 800 km (500 miles) of driving.
Maintenance
 If you tow a trailer, your vehicle will require more frequent
maintenance due to the additional load. For this
information, please refer to the scheduled maintenance
information in the “Owner’s Manual Supplement /
Scheduled Maintenance”.
 Retighten all fixing bolts of the towing ball and bracket after
approximately 1000 km (600 miles) of trailer driving.
Pretowing safety check
 Check that your vehicle remains level when a loaded or
unloaded trailer is hitched. Do not drive if the vehicle has
an abnormal nose −up or nose− down condition, and check
for improper tongue load, overload, worn suspension or
other possible causes.
 Make sure the trailer cargo is securely loaded so that it
cannot shift.
 Check that your rear view mirrors conform to any federal,
state/provincial or local regulations. If they do not, install
required rear view mirrors appropriate for towing purposes.