low LEXUS LX470 2006 Owner's Guide

GAUGES, METERS AND SERVICE REMINDER INDICATORS
49
Your vehicle may overheat during severe operating conditions,
such as:

Driving up a long hill on a hot day.
 Reducing speed or stopping after high speed driving.
 Idling for a long period with the air conditioning on in
stop−and−go traffic.
 Towing a trailer.
NOTICE
Do not remove the thermostat in the engine cooling
system as this may cause the engine to overheat. The
thermostat is designed to control the flow of coolant
to keep the temperature of the engine within the
specified operating range.
 Do not continue driving with an overheated engine.
See “If your vehicle overheats” on page 338.
ENGINE OIL PRESSURE GAUGE
13X623
 1
Normal driving 2Idling
The engine oil pressure gauge indicates engine oil
pressure when the ignition is on. Check it while driving to
make sure the needle is in the proper range.
If the engine oil pressure should stay below the normal range,
pull off the road to a safe place and stop the engine
immediately. Call a Lexus dealer or qualified repair shop for
assistance.
Engine oil pressure may not build up when the engine oil level
is too low. The engine oil pressure gauge is not designed to
indicate engine oil level, and the engine oil level must be
checked using the level dipstick.

GAUGES, METERS AND SERVICE REMINDER INDICATORS
50
NOTICE
Do not drive the vehicle with the engine oil pressure
below the normal range until the cause is fixed it may
ruin the engine.
VOLTMETER
13X503a
 1 Normal range 2Charging system warning light
The voltmeter tells whether the battery is charged or
discharged. Check it while the engine is running the
needle should always indicate as shown above.
If the needle reads below or above the normal range while the
engine is running, it indicates the charging system needs
immediate repair.
However, it is normal for the needle to drop below the normal
range during engine starting.

GAUGES, METERS AND SERVICE REMINDER INDICATORS
51
TACHOMETER
13X504c
The tachometer indicates engine speed in thousands of
rpm (revolutions per minute). Use it while driving to
prevent engine overrevving.
Driving with the engine running too fast causes excessive
engine wear and poor fuel economy. Remember, in most
cases the slower the engine speed, the greater the fuel
economy.
NOTICE
Do not let the indicator needle get into the red zone. This
may cause severe engine damage.
ODOMETER AND TRIP METER
13X505
“ODO/TRIP” knob
This meter displays the odometer and two trip meters. To
change the mode indication, push the “ODO/TRIP” knob
briefly. Each time you push the knob, the mode changes
in order from the odometer to trip meter A to trip meter B,
then back to the odometer, etc.
The odometer records the total distance the vehicle has
been driven. The twin trip meter records two different
distances independently.
For example, you can use one meter to calculate the fuel
economy and the other to measure the distance on each trip.
To set the A trip meter to zero, display the A meter reading,
push the knob and hold it. The same applies for the B trip
meter.
The data of trip meters will be cancelled if the electrical power
source is disconnected.

GAUGES, METERS AND SERVICE REMINDER INDICATORS
54
(a) Brake System Warning Light and Buzzer
This light comes on in the following cases when the ignition key
is in the “ON” position.
 When the parking brake is applied ...
This light comes on for a few seconds when the ignition key is
in the “ON” position even after the parking brake is released.
 When the brake fluid level is low ...
CAUTION
It is dangerous to continue driving normally when the
brake fluid level is low.
When the hydraulic brake booster fails ...
If the hydraulic booster causes a problem resulting in poor
braking performance, the warning light comes on and buzzer
sounds continuously.
Have your vehicle checked at your Lexus dealer in the
following cases:
 The light does not come on even if the parking brake is
applied when the ignition key is in the “ON” position.
 The light does not come on even if the ignition key is turned
on with the parking brake released.
A warning light turning on briefly during operation does not
indicate a problem.
CAUTION
If any of the following conditions occurs, immediately
stop your vehicle at a safe place and contact your Lexus
dealer.
 The light does not turn off even after the parking
brake is released while the engine is running.
 The warning buzzer comes on together with the
warning light.
In either case, this can indicate that the brakes may not
work properly and your stopping distance will become
longer. Depress the brake pedal firmly and bring the
vehicle to an immediate stop.
 The brake system warning light remains on together
with the “ABS” warning light.
In this case, not only the antilock brake system will fail,
but also the vehicle will become extremely unstable
during braking.

GAUGES, METERS AND SERVICE REMINDER INDICATORS
55
Any of the following conditions may occur, but do not
indicate the malfunction:

The light may stay on for about 60 seconds after the ignition
key is turned to the “ON” position. It is normal if it turns off
after a while.
 Depressing the brake pedal repeatedly may turn on the
warning light and buzzer. It is normal if the light turns off and
the buzzer stops sounding after a few seconds.
 You may hear a small sound in the engine compartment
after the engine is started or the brake pedal is depressed
repeatedly. This is a pump pulsating sound of the brake
system, and it is not a malfunction.
(b) Driver’s Seat Belt Reminder Light and
Buzzer
The light and buzzer act as a reminder to buckle up the driver’s
seat belt.
Once the ignition key is turned to “ON” or “START”, the
reminder light flashes and buzzer sounds if the driver’s seat
belt is not fastened. Unless the driver fastens the belt, the light
continues flashing and the buzzer stops after about 4 to 8
seconds.
(c) Front Passenger’s Seat Belt ReminderLight
The light acts as a reminder to have the front passenger buckle
up the seat belt.
Once the ignition key is turned to “ON” or “START”, the
reminder light flashes if a passenger sits in the front passenger
seat and does not fasten the seat belt. Unless the front
passenger fastens the belt, the light continues flashing.
If luggage or other load is placed on the front passenger seat,
depending on its weight and how it is placed on the seat,
built−in sensors in the seat cushion may detect the pressure,
causing the reminder light to flash.

GAUGES, METERS AND SERVICE REMINDER INDICATORS
56
(d) SRS Warning Light
The indicator comes on when the ignition key is turned to
the “ON” position. It goes off after about 6 seconds. This
means the SRS airbags and seat belt pretensioners are
operating properly.
The SRS warning light system monitors the airbag sensor
assembly, front airbag sensors, side and curtain shield airbag
sensor assemblies, curtain shield airbag sensor assemblies,
driver’s seat position sensor, driver’s seat belt buckle switch,
front passenger occupant cassification system and indicator
light, front passenger seat belt buckle switch, inflators, seat
belt pretensioners, roll sensing of curtain shield airbags off
indicator light, interconnecting wiring and power sources.
If any of the following conditions occurs, this indicates a
malfunction of the airbags or seat belt pretensioners. Contact
your Lexus dealer as soon as possible.
The light does not come on when the ignition key is turned
to the “ON” position or remains on for more than 6 seconds
or flashes.
 The light comes on or starts flashing while driving.
The SRS warning light will come on and front passenger
occupant classification indicator light will indicate “OFF” if
there is a malfunction in the front passenger occupant
classification system.
(e) Engine Oil Replacement Reminder Light (U.S.A. only)
The light acts as a reminder to replace the engine oil.
This light will come on when the ignition key is turned to “ON”
and will go off after about a few seconds.
When you drive for about 7200 km (4500 miles) after the
engine oil replacement, this light illuminates for about 3
seconds and then flashes for about 12 seconds with the
ignition key turned to “ON” position. If you continue driving
without the engine oil replacement, and if the driving range
exceeds 8000 km (5000 miles), the light will come on after the
ignition key is turned to “ON” position. The light will remain on\
thereafter.
If the light is flashing, we recommend that you replace the
engine oil at an early opportunity depending on the driving and
road condition. If the light comes on, replace it as soon as
possible.
You need to reset the light after the engine oil replacement.
Reset the light by following the procedure below:
1. Turn the ignition key to th e “LOCK” position with the
odometer re ading shown. (For details, see “Odometer and trip
meter” on page 51.)
2. Turn the ignition key to the “ON” position while holding down
the “ODO/TRIP” knob.
Hold down the knob until the light goes off. Before the light
goes off, it illuminates for 3 seconds, flashes for 2 seconds and
illuminates for 1 second.

GAUGES, METERS AND SERVICE REMINDER INDICATORS
57
If the system fails to reset, the light will remain flashing. In this
case, return to step 1 and try again.
(f) Malfunction Indicator Lamp
This
lamp comes on when the ignition key is turned to the
“ON” position and goes off after the engine starts. This
means that the warning light system is operating properly.
If the lamp remains on, or the lamp comes on while
driving, first check the following:
 Empty fuel tank
If the fuel tank is empty, refuel immediately.
 Loose fuel tank cap
If the fuel tank cap is loose, securely tighten it.
These cases are temporary malfunctions. The malfunction
indicator lamp will go off after taking several driving trips.
If the lamp does not go off even after several trips, contact your
Lexus dealer as soon as possible.
If the fuel tank is not empty or the fuel tank cap is not
loose...
 There is a problem somewhere in the engine, emission
control system, electronic throttle control system, automatic
transmission electrical system or warning light system itself.
Contact your Lexus dealer as soon as possible to service the
vehicle.
If engine speed does not increase when the accelerator pedal
is depressed, there may be a problem somewhere in the
electronic throttle control system. At this time, vibration may occur. However, if you depress the
accelerator pedal more firmly and slowly, you can drive your
vehicle at low speeds. Have your Lexus checked by your
Lexus dealer as soon as possible.
Even if the abnormality of the electronic throttle control system
is corrected during low speed driving, the system may not be
recovered until the engine is stopped and the ignition key is
turned to “ACC” or “LOCK” position.
CAUTION
Be especially careful to prevent erroneous pedal
operation.
Emissions inspection and maintenance (I/M) programs
Your vehicle may not pass a state emission inspection if the
malfunction indicator lamp remains on. Contact your Lexus
dealer to check your vehicle’s emission control system and
OBD (On
−Board Diagnostics) system before taking your
vehicle for the inspection.
For details, see “Emissions inspection and maintenance (I/M)
programs” on page 391.

GAUGES, METERS AND SERVICE REMINDER INDICATORS
58
(g) “ABS” Warning Light
The light comes on when the ignition key is turned to the “ON”
position. If the anti−lock brake system and the brake assist
system work properly, the light turns off after a few seconds.
Thereafter, if either of the systems malfunctions, the light
comes on again.
When the “ABS” warning light is on (and the brake system
warning light is off), the anti−lock brake system, the brake
assist system, the active traction control system and/or the
vehicle stability control system do/does not operate, but the
brake system still operates conventionally.
When the “ABS” warning light is on (and the brake system
warning light is off), the anti−lock brake system does not
operate so that the wheels could lock up during a sudden
braking or braking on slippery road surfaces.
If either of the following conditions occurs, this indicates
a malfunction somewhere in the components monitored
by the warning light system. Contact your Lexus dealer
as soon as possible to service the vehicle.
 The light does not come on when the ignition key is turned
to the “ON” position or remains on.
 The light comes on while you are driving.
A warning light turning on briefly during operation does not
indicate a problem.CAUTION
If the “ABS” warning light remains on together with the
brake system warning light, immediately stop your
vehicle at a safe place and contact your Lexus dealer.
In this case, not only the antilock brake system will fail
but also the vehicle will become extremely unstable
during braking.
Either of the following conditions may occur, but do not
indicate the malfunction:
 The light may stay on for about 60 seconds after the ignition
key is turned to the “ON” position. It is normal if it turns off
after a while.
 Depressing the brake pedal repeatedly may turn on the
light. It is normal if it turns off after a few seconds.
(h) Open Door Warning Light
This light remains on until all the side doors and back door are
completely closed.

GAUGES, METERS AND SERVICE REMINDER INDICATORS
59
(i) Tire Pressure Warning Light
This light comes on when the ignition key is turned to the “ON”
position. If the tire pressure warning system works properly
and tire inflation pressure is appropriate, the light goes off after
a few seconds.
This light comes on or flashes in the following cases when the
ignition key is turned to the “ON” position.
 When the low tire inflation pressure is detected while
driving...
If any tire has low inflation pressure, the light comes on.
The light goes off after the tire inflation pressure is adjusted
to a specified level.
 When initializing the system...
If initialization is completed, the light blinks three times.
 When the system malfunctions...
If the system malfunctions, the light blinks.
Although it is no problem to continue driving, have your
vehicle checked by your Lexus dealer as soon as possible.
(j) Unengaged “Park” Warning Light
This light warns that the transmission “Park” mechanism is not
engaged. If the four −wheel drive control is in the “N” position
while the selector lever is in the “P” position, the transmission
will disengage and the wheels will not lock.
CAUTION
To restore the park function, shift the fourwheel drive
control out of “N”.
(k) Automatic Transmission Fluid Temperature Warning Light
This light warns that the automatic transmission fluid
temperature is too high.
If this light comes on while you are driving, slow down and pull
off the road. Stop the vehicle at a safe place and put the
selector lever in “P” and leave the engine idling until the light
goes off. If the light goes off, you can start the vehicle again.
If the light does not go of f, call a Lexus dealer or qualified repair
shop for assistance.
NOTICE
Continued driving with the warning light on may
damage the automatic transmission.

GAUGES, METERS AND SERVICE REMINDER INDICATORS
60
(l) Vehicle Stability Control System andActive Traction Control System Warning
Light
This light warns that there is a problem somewhere in the
vehicle stability control system and active traction control
system.
If the “VSC/TRAC” warning light and “VSC OFF” indicator light
come on, have your vehicle checked by Lexus dealer as soon
as possible. However, it is no problem that the “VSC/TRAC”
warning light comes on when the brake actuator temperature
becomes high. (For details, see “Active traction control
system” on page 288.)
The lights will stay on with the ignition key turned to “ON”, and
will go off after about a few seconds.
The lights may stay on for 60 seconds after the ignition key is
turned to the “ON” position. It is normal if they go out after a
while.
Depressing the brake pedal repeatedly may turn on the lights.
It is normal if they go out after a few seconds.
When the “VSC/TRAC” warning light and “VSC OFF” indicator
light come on, the vehicle stability control system and/or active
traction control system do not operate, but there is no problem
to continue your driving.
(m) Variable Gear Ratio Steering System Warning Light
This light warns that there is a problem somewhere in the
variable gear ratio steering system.
The light will come on when the ignition key is turned to “ON”
and will go off after a few seconds.
If the light comes on while driving, the system is not working.
Although conventional steering operates when maneuvered,
a larger degree of wheel maneuvering (than at the time when
the system is functioning properly) is needed when driving at
low speed. At this time, the center position of the steering
wheel could be changed. Although it is no problem to continue
driving, have your vehicle repaired at your Lexus dealer.
In the following cases, contact your Lexus dealer:
 The warning light does not come on after the ignition key is
turned to “ON”.
 The warning light remains on after the ignition key is turned
to “ON”.
 The warning light comes on while driving.
The light will flash if you disconnect and reconnect the battery
terminal. This is because the system is reset temporarily.
However, it is no problem to drive. To turn off the light, drive for
a short while. The system will be set automatically and return
to normal.