engine LEXUS RX270 2014 User Guide

57
1-2. Opening, closing and locking the doors
1
Before driving
RX350/270_EE
Locking the front door from the outside without a key
Move the inside lock button to the lock position.
Close the door while pulling the door handle.
The door cannot be locked if the “ENGINE START STOP” switch is in
ACCESSORY or IGNITION ON mode, or the electronic key is left
inside the vehicle.
The key may not be detected correctly and the door may be locked.
Rear door child-protector lock
The door cannot be opened from
inside the vehicle when the lock is
set.
Unlock
Lock
These locks can be set to prevent
children from opening the rear
doors. Push down on each rear
door switch to lock both rear
doors.
STEP1
STEP2
RX350_270_EE_48D77E.book 57 ページ ２０１４年１月２４日　金曜日　午前１０時４分

62
1-2. Opening, closing and locking the doors
RX350/270_EE
Canceling the power back door system (vehicles with a power back door)
Turn off the main switch in the glove box to disable the power back door
system.
On
Off
The back door cannot be operated
even with the wireless remote con-
trol or power back door switch.
■The power back door can be operated when (vehicles with a power back door)
●The back door is unlocked.
●The power back door main switch is on.
●To open the power back door when the “ENGINE START STOP” switch is in
IGNITION ON mode, the power back door main switch must be on, the vehi-
cle speed must be lower than 3 km/h (1 mph) and the shift lever must be in P.
(When using the back door opener button only)
●The “ENGINE START STOP” switch is turned off. (When using the wireless
remote control only)
RX350_270_EE_48D77E.book 62 ページ ２０１４年１月２４日　金曜日　午前１０時４分

63
1-2. Opening, closing and locking the doors
1
Before driving
RX350/270_EE
■Luggage compartment lights
■Back door closer (vehicles with a power back door)
In the event that the back door is left slightly open, the back door closer will auto-
matically close it to the fully closed position.
●The back door closer will operate regardless of the “ENGINE START STOP”
switch mode.
●The back door can be opened while the back door closer is operating by press-
ing the back door opener button.
■Power back door operation (vehicles with a power back door)
●A buzzer sounds to indicate that the back door is opening/closing.
●The back door can still be opened and closed manually, even when the power
back door main switch is off.
●Pressing the back door opener button while the power back door system is
operating will cause the back door to switch to manual operation.
●If anything obstructs the power back door while it is closing/opening, a buzzer
will sound and the back door will automatically operate in the opposite direc-
tion.
●If two or more successive attempts are made to close the back door, a buzzer
will sound and the back door will switch to manual operation.The luggage compartment lights turn on
when the back door is opened with the lug-
gage compartment light switch on.
When the “ENGINE START STOP” switch is
turned off, the lights will go off automatically
after 20 minutes.
RX350_270_EE_48D77E.book 63 ページ ２０１４年１月２４日　金曜日　午前１０時４分

69
1-2. Opening, closing and locking the doors
1
Before driving
RX350/270_EE
CAUTION
■Power back door
Observe the following precautions when operating the power back door.
Failure to do so may cause death or serious injury.
●Check the safety of the surrounding area to make sure there are no obstacles or
anything that could cause any of your belongings to get caught.
●If anyone is in the vicinity, make sure they are safe and let them know that the back
door is about to open or close.
●If the power back door system is turned off with the main switch while the back
door is operating automatically, the automatic operation is stopped. The back
door then has to be operated manually. Take extra care when on an incline, as the
back door may open or close unexpectedly.
●If the operating conditions of the power back door are no longer met, a buzzer
may sound and the back door may stop opening or closing. The back door then
has to be operated manually. Take extra care when on an incline, as the back door
may open or close abruptly.
●On an incline, the back door may suddenly shut after it opens. Make sure the
back door is fully open and secure.
●In the following situations, the power back door may detect an abnormality and
automatic operation may be stopped. In this case, the back door has to be oper-
ated manually. Take extra care when on an incline, as the back door may open or
close abruptly.
• When the back door contacts an obstacle
• When the battery voltage suddenly drops, such as when the “ENGINE
START STOP” switch is turned to IGNITION ON mode or the engine is
started during automatic operation
●If a bicycle carrier or similar heavy object is attached to the back door, the power
back door may not operate, causing itself to malfunction, or the back door may
suddenly shut again after being opened, causing someone’s hands, head or neck
to be caught and injured. When installing an accessory part to the back door,
using a genuine Lexus part is recommended.
RX350_270_EE_48D77E.book 69 ページ ２０１４年１月２４日　金曜日　午前１０時４分

81
1
1-3. Adjustable components (seats, mirrors, steering wheel)
Before driving
RX350/270_EE
Driving position memory∗
Your preferred driving position (the position of the driver's seat, steering
wheel and outside rear view mirrors) can be memorized and recalled with
the touch of a button. It is also possible to set this function to activate auto-
matically when the doors are unlocked.
Three different driving positions can be entered into memory.
On some models, the same buttons are found on the front passenger’s side,
allowing the position of the front passenger’s seat to be memorized.
■Entering a position to memory
Turn the “ENGINE START STOP” switch to IGNITION ON
mode.
Adjust the driver’s seat, steering wheel and outside rear view
mirrors to the desired positions.
Press the “SET” button, then
within 3 seconds press button
“1”, “2” or “3” until the signal
beeps.
If the selected button has
already been preset, the previ-
ously recorded position will be
overwritten.
STEP1
STEP2
STEP3
∗: If equipped
RX350_270_EE_48D77E.book 81 ページ ２０１４年１月２４日　金曜日　午前１０時４分

82
1-3. Adjustable components (seats, mirrors, steering wheel)
RX350/270_EE
■Recalling the memorized position
Check that the shift lever is set in P.
Turn the “ENGINE START STOP” switch to IGNITION ON
mode.
Press button “1”, “2” or “3” until
the signal beeps to recall the
desired position.
STEP1
STEP2
STEP3
RX350_270_EE_48D77E.book 82 ページ ２０１４年１月２４日　金曜日　午前１０時４分

83
1-3. Adjustable components (seats, mirrors, steering wheel)
1
Before driving
RX350/270_EE
Linking driving position memory with door unlock operation (driver’s side only)
Record your driving position to button “1”, “2” or “3” before performing
the following.
Carry only the key (including the card key) to which you want to link the
driving position. If 2 or more keys are in the vehicle, the driving position
cannot be linked properly.
Shift the shift lever to P and close the driver's door. Turn the
“ENGINE START STOP” switch to IGNITION ON mode.
Press the desired button (“1”, “2” or
“3”) to recall the position. Then,
while keep pressing the button,
press the driver's door lock
switches (either lock or unlock)
until the signal beeps.
The driving position is recalled
when the driver's door is unlocked
using the entry function or wireless
remote control and the driver's
door is opened.
STEP1
STEP2
RX350_270_EE_48D77E.book 83 ページ ２０１４年１月２４日　金曜日　午前１０時４分

84
1-3. Adjustable components (seats, mirrors, steering wheel)
RX350/270_EE
Power easy access system (driver’s side only)
When the driver enters and exits the vehicle, the driver's seat and steer-
ing wheel will automatically perform the following operations:
Exiting the vehicle: When all of the
following actions have been per-
formed, the steering wheel will
move up and back to the point far-
thest away from the driver and the
seat will move backward (auto
away function):
• The shift lever has been shifted to P
• The “ENGINE START STOP”
switch has been turned off
• The driver’s seat belt has been
unfastened
Entering the vehicle: When either
of the following actions has been
performed, the steering wheel will
move toward the driver and seat
will move forward (auto return
function):
• The “ENGINE START STOP”
switch has been turned to ACCES-
SORY mode
• The driver’s seat belt has been fas-
tened
RX350_270_EE_48D77E.book 84 ページ ２０１４年１月２４日　金曜日　午前１０時４分

85
1-3. Adjustable components (seats, mirrors, steering wheel)
1
Before driving
RX350/270_EE
■When driving position memory is linked with door unlock operation
If the driver’s door is opened, the driver’s seat will move toward the memorized
position but stop slightly beforehand to allow easy access to the vehicle.
Turning the “ENGINE START STOP” switch to ACCESSORY mode or fastening
the driver’s seat belt moves the seat fully into the memorized position.
■Canceling the linked door unlock operation
Turn the “ENGINE START STOP” switch to IGNITION ON mode and
close the driver's door.
While pressing the “SET” button, press the driver’s door lock switches
(either lock or unlock) until the signal beeps.
■Operating the driving position memory after turning the “ENGINE START
STOP” switch off
Memorized positions (except for the steering wheel position) can be activated up
to 180 seconds after the driver’s door is opened and another 60 seconds after it is
closed again, even after turning the “ENGINE START STOP” switch off.
■Stopping seat position operation part-way through
Perform any of the following operations:
●Press the “SET” button.
●Press button “1”, “2” or “3”.
●Adjust the seat using the switches (only cancels seat position recall).
●Adjust the steering wheel using the tilt and telescopic steering control switch
(only cancels steering wheel position recall).
■Correct seat position
When the seat is in the most forward or most backward position, and the seat is
being moved in those directions, the system may not correctly recognize the cur-
rent position and the memorized position will not be correctly recalled.
■The auto away function for exiting the driver seat
If the seat is already close to the rearmost position, the auto away function may not
operate when the driver exits the vehicle.
■Customization
The distance that the driver’s seat moves backward during the auto away function
can be changed. (Customizable features →P. 6 2 2 )
STEP1
STEP2
RX350_270_EE_48D77E.book 85 ページ ２０１４年１月２４日　金曜日　午前１０時４分

94
1-3. Adjustable components (seats, mirrors, steering wheel)
RX350/270_EE
Steering wheel
Auto tilt away
When the “ENGINE START
STOP” switch is turned off, the
steering wheel returns to its
stowed position by moving up and
away to enable easier driver entry
and exit.
Tu r n i n g t h e “ E N G I N E S T A R T
STOP” switch to ACCESSORY or
IGNITION ON mode will return
the steering wheel to the original
position.
The steering wheel can be adjusted to a comfortable position.
Operating the switch moves the steering wheel in the following direc-
tions:
Up
Down
Away from the driver
Toward the driver
RX350_270_EE_48D77E.book 94 ページ ２０１４年１月２４日　金曜日　午前１０時４分