ECO LEXUS RX270 2014 Repair Manual

225
2-3. Operating the lights and windshield wipers
2
When driving
RX350/270_EE
■Raindrop sensor
●If the wiper switch is turned to the position while the “ENGINE START
STOP” switch is in IGNITION ON mode, the wipers will operate once to show
that AUTO mode is activated.
●When the sensor sensitivity ring is turned toward high while in AUTO mode, the
wipers will operate once to indicate that the sensor sensitivity is enhanced.
●If the temperature of the raindrop sensor is 90°C (194°F) or higher, or -15°C
(5°F) or lower, automatic operation may not occur. In this case, operate the wip-
ers in any mode other than AUTO.
■If no windshield washer fluid sprays
Check that the washer nozzles are not blocked if there is washer fluid in the wind-
shield washer fluid reservoir.
CAUTION
■Caution regarding the use of windshield wipers in AUTO mode
The windshield wipers may operate unexpectedly if the sensor is touched or the
windshield is subject to vibration in AUTO mode. Take care that your fingers etc. do
not become caught in the windshield wipers.
■Caution regarding the use of washer fluid
When it is cold, do not use the washer fluid until the windshield becomes warm. The
fluid may freeze on the windshield and cause low visibility. This may lead to an acci-
dent, resulting in death or serious injury.
●The raindrop sensor judges the amount
of raindrops.
An optical sensor is adopted. It may not
operate properly when sunlight from the
rising or setting of the sun intermittently
strikes the windshield, or if bugs etc. are
present on the windshield.
RX350_270_EE_48D77E.book 225 ページ ２０１４年１月２４日　金曜日　午前１０時４分

226
2-3. Operating the lights and windshield wipers
RX350/270_EE
NOTICE
■When the windshield is dry
Do not use the wipers, as they may damage the windshield.
■When the washer fluid tank is empty
Damage to the washer fluid pump may be caused if the lever is pulled toward you
and held continually.
■When a nozzle becomes blocked
In this case, contact any authorized Lexus dealer or repairer, or another duly quali-
fied and equipped professional.
Do not try to clear it with a pin or other object. The nozzle will be damaged.
RX350_270_EE_48D77E.book 226 ページ ２０１４年１月２４日　金曜日　午前１０時４分

228
2-3. Operating the lights and windshield wipers
RX350/270_EE
NOTICE
■When the rear window is dry
Do not use the wipers, as they may damage the rear window.
■When the washer fluid tank is empty
Damage to the washer fluid pump may be caused if the lever is operated continu-
ally.
■When a nozzle becomes blocked
In this case, contact any authorized Lexus dealer or repairer, or another duly quali-
fied and equipped professional.
Do not try to clear it with a pin or other object. The nozzle will be damaged.
RX350_270_EE_48D77E.book 228 ページ ２０１４年１月２４日　金曜日　午前１０時４分

231
2-4. Using other driving systems
2
When driving
RX350/270_EE
Accelerate or decelerate the
vehicle to the desired speed,
and push the lever down to set
the speed.
“SET” will be displayed.
The vehicle speed at the
moment the lever is released
becomes the set speed.
■Adjusting the set speed
To change the set speed, operate the lever until the desired set
speed is obtained.
Increases the speed
Decreases the speed
Fine adjustment: Momentarily
move the lever in the desired
direction.
Large adjustment: Hold the
lever in the desired direction.
The set speed will be increased or decreased as follows:
Fine adjustment: By approximately 1.6 km/h (1 mph) each time the lever is
operated.
Large adjustment: The set speed can be increased or decreased continu-
ally until the lever is released.
STEP2
RX350_270_EE_48D77E.book 231 ページ ２０１４年１月２４日　金曜日　午前１０時４分

235
2-4. Using other driving systems
2
When driving
RX350/270_EE
Accelerate or decelerate the
vehicle to the desired speed,
and push the lever down to set
the speed.
“SET” will be displayed.
The vehicle speed at the
moment the lever is released
becomes the set speed.
■Adjusting the set speed
To change the set speed, operate the lever until the desired set
speed is displayed.
Increases the speed
Decreases the speed
Fine adjustment: Momentarily
move the lever in the desired
direction.
Large adjustment: Hold the
lever in the desired direction.
In the vehicle-to-vehicle distance control mode, the set speed will be
increased or decreased as follows:
STEP2
RX350_270_EE_48D77E.book 235 ページ ２０１４年１月２４日　金曜日　午前１０時４分

240
2-4. Using other driving systems
RX350/270_EE
Selecting conventional constant speed control mode
Constant speed control mode differs from vehicle-to-vehicle distance
control mode. When constant speed control mode is selected, your vehi-
cle will maintain a set speed regardless of whether or not there are other
vehicles in the lane ahead.
Press the “ON-OFF” button to
activate the cruise control.
Press the button again to deacti-
vate the cruise control.
Switch to constant speed con-
trol mode.
(Push the lever forward and
hold for approximately one sec-
ond.)
Constant speed control mode indi-
cator will come on.
When in constant speed control
mode, to return to vehicle-to-vehi-
cle distance control mode, push
the lever forward again and hold
for approximately 1 second.
After the desired speed has been
set, it is not possible to return to
vehicle-to-vehicle distance control
mode.
If the “ENGINE START STOP”
switch is turned off and then turned
to IGNITION ON mode again, the
vehicle will automatically return to
vehicle-to-vehicle distance control
mode.
RX350_270_EE_48D77E.book 240 ページ ２０１４年１月２４日　金曜日　午前１０時４分

257
2-4. Using other driving systems
2
When driving
RX350/270_EE
Selecting vehicle height
■Height modes
●“HI” mode: For driving on bumpy roads
30 mm (1.2 in.) higher than the normal height
“HI” mode cannot be selected when vehicle speed exceeds 30 km/h (19
mph).
●“N” mode: For ordinary driving
Normal height
●“LO” mode: For sporty driving
Vehicle front: 20 mm (0.8 in.) lower than the normal height
Vehicle rear: 5 mm (0.2 in.) lower than the normal height
●Luggage mode: For easy entry/exit and easy luggage loading/
unloading
30 mm (1.2 in.) lower than the normal height
■Height selector switch
Press the height selector switch for approximately 1 second.
Driver’s side instrument panel
Higher
Pressing this switch while the vehi-
cle is in luggage mode changes the
vehicle height to that of “N” mode.
Lower
Pressing this switch while the vehi-
cle is in “LO” mode changes the
vehicle height to that of luggage
mode.
RX350_270_EE_48D77E.book 257 ページ ２０１４年１月２４日　金曜日　午前１０時４分

259
2-4. Using other driving systems
2
When driving
RX350/270_EE
■Operating conditions
After stopping the engine, the vehicle will remain lowered for a maximum of 60
seconds.
●Height selector switch (driver's side instrument panel)
• While the engine is running, any vehicle height mode can be selected.
• Luggage mode can only be selected when the shift lever is in P position.
●Height selector switch (luggage compartment)
• When the engine is running and the shift lever is in the P position, any vehicle
height other than “LO” mode can be selected.
• When the “ENGINE START STOP” switch is turned off, the vehicle height
can only be lowered (only the “∨” side of the switch can be operated).
This switch can only be operated when the back door is open.
●Height control off switch
When the vehicle is stopped with the “ENGINE START STOP” switch in IGNI-
TION ON mode, vehicle height control can be disabled/re-enabled.
■When changing vehicle height modes
Before operating the height selector switch to raise/lower the vehicle height,
ensure that there are no objects in the surrounding area that could damage the
vehicle.
■When “N” mode is selected
During high speed driving, the vehicle height will automatically change to that of
“LO” mode.
■When “HI” mode is selected
The vehicle height will change to that of “N” mode when vehicle speed reaches 50
km/h (31 mph) or when vehicle speed has exceeded 30 km/h (19 mph) for approx-
imately 10 seconds. Even if vehicle speed is reduced below 30 km/h (19 mph), the
vehicle height will not automatically return to “HI” mode.
■When “LO” mode is selected
The vehicle height will change to that of “N” mode when the engine is restarted.
RX350_270_EE_48D77E.book 259 ページ ２０１４年１月２４日　金曜日　午前１０時４分

260
2-4. Using other driving systems
RX350/270_EE
■When luggage mode is selected
If the vehicle begins to move while still in luggage mode, the vehicle will automati-
cally change to “N” mode once speed exceeds 8 km/h (5 mph). Even if vehicle
speed is reduced below 8 km/h (5 mph), the vehicle height will not automatically
return to luggage mode.
■Operating sound of the air suspension
When the vehicle height is lowered, such as when entering and loading the vehicle,
or when the height selector switch is operated, the sound of the compressor oper-
ating or the mode changing may be heard. This does not indicate a malfunction.
■Automatic leveling function
Regardless of the number of occupants and the luggage load, vehicle height in any
mode is always adjusted to a fixed height by the automatic leveling function.
■Vehicle height mode change time
●If the height control is operated continuously to lower the vehicle, the suspen-
sion air tank may become full, causing operation of the vehicle height lowering
control to become slow.
●To protect the compressor, the system will only raise the vehicle for a total of
100 consecutive seconds. If it takes longer than this to reach the selected
height, operation may be suspended shortly and then restart. However, it may
not be possible to change the vehicle's height mode at this time.
■The electronically modulated air suspension will not operate when
The vehicle height control may not be able to change modes when the vehicle runs
over a high curb or other rugged surfaces where the suspension is stretched.
RX350_270_EE_48D77E.book 260 ページ ２０１４年１月２４日　金曜日　午前１０時４分

261
2-4. Using other driving systems
2
When driving
RX350/270_EE
CAUTION
■The electronically modulated air suspension must be turned off when
The electronically modulated air suspension must be turned off in the following situ-
ations as vehicle height may change due to the automatic leveling function, and, you
may catch part of your body in the vehicle and cause an accident, resulting in death
or serious injury.
●Any of the wheels is stuck in a ditch.
●It is necessary to jack up the vehicle.
●It is necessary to tow the vehicle with part of it lifted.
●When connecting/disconnecting a trailer
For safety, stop the engine if necessary.
■“HI” mode
●“HI” mode should only be used when driving on rough roads, for example when
driving off-road. Because the vehicle's center of gravity will become higher when
in the mode, the vehicle may become unstable when turning abruptly and cause
an accident, resulting in death or serious injury.
●Do not select “HI” mode when loading cargo on the roof luggage carrier.
Because the vehicle's center of gravity will become higher when in the mode, the
vehicle may become unstable when turning abruptly, and cause an accident,
resulting in death or serious injury.
RX350_270_EE_48D77E.book 261 ページ ２０１４年１月２４日　金曜日　午前１０時４分