light LEXUS RX350 2016 Owner's Guide

80
RX350_U_OM48E90U 2. Instrument cluster 
Except F SPORT models 
F SPORT models
The units used on the meter and some indicators may differ depending on the
target region.Warning lights and indicators The warning lights and indicators on th e instrument cluster, center panel and
outside rear view mirrors inform the driv er of the status of the vehicle’s vari-
ous systems.
For the purpose of explanation, the following illustration displays all warning
lights and indicators illuminated.

812. Instrument cluster
2
Instrument cluster
RX350_U_OM48E90U Warning lights inform the driver of malfun ctions in any of the vehicle’s systems.
Warning lights * 1
(U.S.A.)
Brake system warning light
(  P. 6 3 4 )
* 1
(Canada)
ABS warning light
(  P. 6 3 4 )
* 1
(Canada)
Brake system warning light
(  P. 6 3 4 )
* 2
(U.S.A.)
Parking brake indicator
(  P. 6 3 5 )
* 1
Brake system warning light
(  P. 6 3 4 )
* 2
(Canada)
Parking brake indicator
(  P. 6 3 5 )
* 1
(if equipped)
Charging system warning
light (  P. 6 3 4 ) * 1, 2
Brake hold operated
indicator (  P. 6 3 5 )
* 1
(U.S.A.)
Malfunction indicator lamp
(  P. 6 3 4 ) * 1
Electric power steering
system warning light
(  P. 6 3 5 )
* 1
(Canada)
Malfunction indicator lamp
(  P. 6 3 4 ) * 1
Electric power steering
system warning light
(  P. 6 3 5 )
* 1
SRS warning light
(  P. 6 3 4 ) (if equipped)
LDA indicator (  P. 6 3 5 )
LKA indicator (  P. 6 3 5 )
* 1
(U.S.A.)
ABS warning light
(  P. 6 3 4 ) * 1
Slip indicator (  P. 6 3 5 )

82 2. Instrument cluster
RX350_U_OM48E90U * 1
: These lights turn on when the engine switch is turned to IGNITION ON mode to
indicate that a system check is being perfor med. They will turn off after the engine is
started, or after a few seconds. There may be a malfunction in a system if the lights do
not turn on, or turn off. Have the vehicle inspected by your Lexus dealer.
* 2
: The light flashes to indicate a malfunction.
The indicators inform the driver of the op erating state of the vehicle’s various sys-
tems. * 1, 2
(if equipped)
PCS warning light
(  P. 636)
* 1
Tire pressure warning light
(  P. 636)
Low fuel level warning light
(  P. 636)
* 1
Master warning light
(  P. 636)
Seat belt reminder light
(  P. 636)
Indicators Turn signal indicator
(  P. 2 3 4 ) Cruise control indicator
(  P. 302, 314, 326)
(U.S.A.)
Headlight indicator
(  P. 2 4 1 ) (if equipped)
Radar cruise control
indicator (  P. 302, 314)
(Canada)
Tail light indicator
(  P. 2 4 1 ) Cruise control “SET”
indicator
(  P. 302, 314, 326)
Headlight high beam
indicator (  P. 2 4 2 ) (if equipped)
LDA indicator (  P. 2 9 3 )
LKA indicator (  P. 2 8 3 )
* 1
(if equipped) Automatic High Beam
indicator (  P. 2 4 5 ) (if equipped)
LDA indicator (  P. 2 9 3 )
LKA indicator (  P. 2 8 3 )
Fog light indicator
(  P. 2 4 9 ) * 4
(if equipped)LDA indicator (  P. 2 9 3 )
LKA indicator (  P. 2 8 3 )

832. Instrument cluster
2
Instrument cluster
RX350_U_OM48E90U ●
Drive mode indicators 
Except F SPORT models (if equipped)
Intuitive parking assist
indicator (  P. 3 3 0 ) (Canada)
Parking brake indicator
(  P. 235, 236)(if equipped)
“BSM” indicator (  P. 3 5 5 )
* 1
Brake hold standby
indicator (  P. 2 3 9 )(if equipped)
“RCTA” indicator
(  P. 3 5 5 )
* 1
Brake hold operated
indicator (  P. 2 3 9 )
* 2, 3
(if equipped)
BSM outside rear view
mirror indicators
(  P. 3 5 5 ) * 1
Eco Driving Indicator Light
(  P. 1 0 4 )
* 1, 4
Slip indicator (  P. 3 76 )
* 6
Security indicator
(  P. 74 , 76 )
* 1, 5
VSC OFF indicator
(  P. 377) * 1
(AWD
models only)
All-wheel drive lock
indicator (  P. 3 7 3 )
* 1, 5
(if equipped)
PCS warning light
(  P. 2 74 ) * 7
Low outside temperature
indicator (  P. 8 5 )
(U.S.A.)
Parking brake indicator
(  P. 2 3 5 ) * 1, 6
“A I R B A G O N / O F F ”
indicator (  P. 4 9 )
Eco drive mode indicator
(  P. 3 6 9 ) “SPORT” indicator
(  P. 3 6 9 )

84 2. Instrument cluster
RX350_U_OM48E90U 
F SPORT models
* 1
: These lights turn on when the engine switch is turned to the IGNITION ON mode to
indicate that a system check is being perfor med. They will turn off after the engine is
started, or after a few seconds. There may be a malfunction in a system if the lights do
not turn on, or turn off. Have the vehicle inspected by your Lexus dealer.
* 2
: In order to confirm operation, the BSM outside rear view mirror indicators illuminate
in the following situations:
• When the BSM function is enabled on of the multi-information display, the
engine switch is turned to IGNITION ON mode.
• When the engine switch is in IGNITION ON mode, the BSM function is enabled
on of the multi-information display.
If the system is functioning correctly, the BSM outside rear view mirror indicators will
turn off after a few seconds.
If the BSM outside rear view mirror indica tors do not illuminate or do not turn off,
there may be a malfunction in the system.
If this occurs, have the vehicle inspected by your Lexus dealer.
* 3
: This light illuminates on the outside rear view mirrors.
* 4
: The light flashes to indicate that the system is operating.
* 5
: The light comes on when the system is turned off.
* 6
: This light illuminates on the center panel.
* 7
: When the outside temperature is approximately 37  F (3  C) or lower, the indicator
will flash for approximately 10 seconds, then stay on.Eco drive mode indicator
(  P. 3 6 9 ) “SPORT S” indicator
(  P. 3 6 9 )
“SPORT S+” indicator
(  P. 3 6 9 ) “CUSTOMIZE” indicator
(  P. 3 6 9 )
WA R N I N G ■
If a safety system warning light does not come on
Should a safety system light such as the ABS and SRS warning light not come on when
you start the engine, this could mean that these systems are not available to help pro-
tect you in an accident, which could result in death or serious injury. Have the vehicle
inspected by your Lexus dealer immediately if this occurs.

872. Instrument cluster
2
Instrument cluster
RX350_U_OM48E90U ■
Rev indicator (F SPORT models)
When the engine reaches a set
speed, a ring-shaped indicator will
be displayed on the tachometer. The desired engine speed at which
the Rev indicator will begin to be dis-
played can be set on of the multi-
information display. (  P. 9 6 )
■
Rev peak (F SPORT models)
The engine speed reaches or
exceeds 5000 rpm, an afterimage
of the tachometer will be displayed
at the highest engine speed for
approximately 1 second.
The brightness of the instrument panel lights can be adjusted.
Darker
Brighter • The brightness of the instrument
panel lights can be adjusted individu-
ally for day mode and night mode
* .
• If the brightness is adjusted when the
surroundings are bright and the tail
lights are on (day mode brightness
adjustment), the brightness level of
night mode will be adjusted at the
same time.
* : Day mode and night mode:  P. 8 8Instrument panel light control 1
2

88 2. Instrument cluster
RX350_U_OM48E90U ■
The meters and display illuminate when
The engine switch is in IGNITION ON mode. ■
Brightness of the meters (day mode and night mode)
The brightness of the meters is changed between day mode and night mode. ●
Day mode: When the tail lights are off or when the tail lights are on but the surrounding
area is bright ●
Night mode: When the tail lights are on and the surrounding area is dark ■
Outside temperature display ●
In the following situations, the correct outside temperature may not be displayed, or the
display may take longer than normal to change.
• When stopped, or driving at low speeds (less than 12 mph [20 km/h])
• When the outside temperature has changed suddenly (at the entrance/exit of a
garage, tunnel, etc.) ●
When “  ” or “E” is displayed, the sy stem may be ma lfunctioning.
Take your vehicle to your Lexus dealer. ■
Clock settings screen (vehicles with a navigation system only)
If the clock adjustment screen is displayed continuously when attempting to change the
clock settings, the system may be malfunctioning.
Have the vehicle inspected by your Lexus dealer. ■
Customization
Some functions can be customized. (  P. 9 6 )
NOTICE ■
To prevent damage to the engine and its components ●
Do not let the indicator needle of the tachometer enter the red zone, which indicates
the maximum engine speed. ●
The engine may be overheating if the engine coolant temperature gauge is in the red
zone (H). In this case, immediately stop the vehicle in a safe place, and check the
engine after it has cooled completely. (  P. 6 6 8 )

1012. Instrument cluster
2
Instrument cluster
RX350_U_OM48E90U ■
Meter settings Scheduled maintenance (U.S.A. only)
Maintenance data reset Select to reset the message indicating
maintenance is required, after the
required maintenance is performed.
(  P. 565)
Oil maintenance
Engine oil maintenance data reset Select to reset the engine oil mainte-
nance information (message indicat-
ing maintenance is required and
distance until the next oil change)
after engine oil maintenance is per-
formed. (  P. 577)Item Settings Details
Item Settings Details
Language Select to change the language dis-
played.
Units Select to change the units of measure
displayed.
(Eco Driving
Indicator Light) On
Select to enable/disable the Eco Driv-
ing Indicator Light. (  P. 1 0 4 )
Off
Switch settings Select to display how to change the
top screen.
Drive information 1 Select to select up to 2 items that will
be displayed on each Drive informa-
tion screen (Drive information 1
screen, Drive information 2 screen,
and Drive inform ation 3 screen)
respectively.
(Selectable items:  P. 9 3 )Drive information 2
Drive information 3

104 2. Instrument cluster
RX350_U_OM48E90U Displays suggestions to the driver in the following situations. To select a response
to a displayed suggestion, use the meter control switches. The suggestion function can be turn ed on/off. (Customizable features:  P. 700)■
Suggestion to enable the power back door
If the power back door system is disabled (setting on set to off) and the
power back door switch on the instru ment panel is operated, a suggestion
message will be displayed asking if yo u wish to enable the power back door
system. To enable the power back door system, select “Yes”. After enabling the power back door syst em, press the power back door switch
again to open or close the power back door.■
Suggestion to turn off the headlights
If the headlights are left on for a certai n amount of time after the engine switch
has been turned off, a suggestion message will be displayed asking if you wish
to turn the headlights off. To turn the headlights off, select “Yes”.If a front door is opened after the engine switch is turned off, this suggestion mes-
sage will not be displayed.■
Eco Driving Indicator
Eco Driving Indicator will not operat e under the following conditions:●
The shift lever is in any position other than D. ●
A paddle shift switch (i f equipped) is operated.●
Sport mode is selected. ●
The vehicle speed is approximately 80 mph (130 km/h) or higher.Suggestion function
Eco Driving Indicator Light
During Eco-friendly acceleration (Eco driv-
ing), the Eco Driving Indicator Light will turn
on. When the acceleration exceeds the Zone
of Eco driving, or when the vehicle is stopped,
the light turns off.
Eco Driving Indicator Zone Display
Suggests the Zone of Eco driving with current
Eco driving ratio based on acceleration.
Eco driving ratio based on acceleration
If the acceleration exceeds the Zone of Eco
driving, the right side of the Eco Driving Indi-
cator Zone Display will illuminate.
Zone of Eco driving 1
2
3
4

1052. Instrument cluster
2
Instrument cluster
RX350_U_OM48E90U ■
Background color of the indicator/shift position display area (except F SPORT models)
The background color of the indicator/shift position display area is changed according to
the driving mode as follows (  P. 3 6 9 ) :●
Eco drive mode: Blue ●
Sport mode: Red ■
G-force display (if equipped) ●
The G-force values may not be zero even when the vehicle is parked, such as when it is
parked on an incline. ●
Depending on the vehicle usage conditions, the brake fluid pressure display may not
reach its maximum reading even though the brake pedal is fully depressed.●
If a battery terminal is disconnected and reconnected, the steering amount display may
be disabled temporarily. After driving the vehi cle for a while, the display will be enabled.■
Suspension of the settings display ●
Some settings cannot be changed while driv ing. When changing settings, park the
vehicle in a safe place. ●
If a warning message is displayed, operation of the settings displa y will be suspended.■
Tire pressure ●
It may take a few minutes to display the tire inflation pressure after the engine switch is
turned to IGNITION ON mode. It may also take a few minutes to display the tire infla-
tion pressure after inflation pressure has been adjusted. ●
“---” may be displayed if the tire position information cannot be determined due to
unfavorable radio wave conditions. ●
Tire inflation pressure changes with temperat ure. The displayed values may also be dif-
ferent from the values measured using a tire pressure gauge.■
Liquid crystal display
Small spots or light spots may appear on the display. This phenomenon is characteristic
of liquid crystal displays, and there is no problem continuing to use the display. ■
Customization
Some functions can be customized. (  P. 9 6 , 6 9 9 )