shock LEXUS SC300 1991 Service Workshop Manual

TORQUE SPECIFICATIONS
SA0WG±03
(FRONT)
\
 \
Part tightened NVm kgf Vcm ft Vlbf
\
 \
Hub nut 103 1,050 76
\
 \
Front and rear adjusting cam bolt 226 2,300 166
\
 \
Axle hub lock nut 199 2,030 147
\
 \
Lower ball joint X Steering knuckle 125 1,270 92
\
 \
Tie rod end X Steering knuckle 49 500 36
\
 \
Steering knuckle X Upper suspension arm 103 1,050 76
\
 \
Lower ball foint X Lower suspension arm 127 1,300 94
\
 \
Disc brake caliper X Steering knuckle 11 8 1,200 87
\
 \
Speed sensor set bolt 103 80 76 in. Vlbf
\
 \
Front shock absorber X Body 35 360 26
\
 \
Front shock absorber X Lower suspension arm 143 1,460 106
\
 \
Upper suspension arm mounting nut 164 1,670 121
\
 \
Piston rod lock nut 29 300 22
\
 \
Stabilizer link X Lower suspension arm 74 750 54
\
 \
Stabilizer link X Stabilizer bar 74 750 54
\
 \
Stabilizer bar bracket X Body 18 180 13
\
 \
Steering knuckle X Disc brake dust cover 19 195 14
(REAR)
\
 \
Part tightened N Vm kgf Vcm ft Vlbf
\
 \
Shock absorber X Lower suspension arm 143 1,460 106\
 \
Upper arm X Body 164 1,670 271\
 \
Rear axle carrier X Brake caliper 104 1,065 77\
 \
No. 1 lower arm X Rear axle carrier 59 600 43\
 \
No. 1 lower arm X Body 184 1,880 136
\
 \
No. 2 lower arm X Rear axle carrier 150 1,525 11 0
\
 \
No. 2 lower arm X Body 184 1,880 136
\
 \
Strut rod X Rear axle carrier 184 1,880 136
\
 \
Strut rod X Body 184 1,880 136
\
 \
Rear drive shaft X Axle hub 289 2,950 213
\
 \
Upper ball joint X Rear axle carrier 109 1,110 80
\
Parking brake backing plate X Rear axle carrier2626019\
 \
Rear drive shaft X Differential 83 850 64\
 
\

\
Differential mounting bolt \
Front
Rear 

147
142 

1,500
1,450 

108
105
\
 \
Differential carrier cover set bolt 47 475 34
\
 \
Suspension support X Body 27 280 20
\
 \
Suspension support X Shock absorber rod 27 280 20
\
 \
Stabilizer bar link nut 74 750 54
\
 \
Stabilizer bar bushing retainer bolt 28 290 21
±
SUSPENSION AND AXLE SERVICE SPECIFICATIONSSA±129
WhereEverybodyKnowsYourName

4. CHECK WHEEL BEARING LOOSENESS
(a) Check the backlash in bearing shaft direction.
Maximum: 0.05 mm (0.0020 in.)
(b) Check the axle hub deviation.
Maximum: 0.05 mm (0.0020 in.)
5. CHECK FRONT SUSPENSION FOR LOOSENESS
6. CHECK STEERING LINKAGE FOR LOOSENESS
7. CHECK BALL JOINT FOR EXCESSIVE LOOSENESS
8. CHECK SHOCK ABSORBER WORK PROPERLYwCheck for oil leak
w Check mounting busings for wear
w Bounce front and rear of the vehicle
SA±4
±
SUSPENSION AND AXLE GENERAL INSPECTION
WhereEverybodyKnowsYourName

FRONT SHOCK ABSORBER
COMPONENTS
SA00A±0A
±
SUSPENSION AND AXLE FRONT SUSPENSIONSA±27
WhereEverybodyKnowsYourName

FRONT SHOCK ABSORBER REMOVAL
SA0RN±04
1. JACK UP VEHICLE AND REMOVE FRONT WHEEL
2. REMOVE BRAKE CALIPER
(a) Remove the 2 bolts and caliper from the steering knuckle.
(b) Hang up the brake caliper using wire, etc.
3. REMOVE FRONT FENDER SPLUSH SHIELD
4. LH side only:MOVE WASHER TANK
(a) Remove the bolt.
(b) Remove the bolt and move the washer tank away from the body.
5. DISCONNECT ABS SPEED SENSOR AND WIRE HARNESS
(a) Remove the bolt and disconnect the speed sensor from the
steering knuckle.
SA±28
±
SUSPENSION AND AXLE FRONT SUSPENSION
WhereEverybodyKnowsYourName

(b) Remove the 3 bolts and disconnect the wire harness clampto prevent the wire harness being damaged when removing
or installing the through bolt.
6. LOOSEN PISTON ROD LOCK NUT
(a) Remove the plug from the support.
(b) Loosen the lock nut in the middle of the suspension support.
NOTICE: Only loosen the nut, do not remove it.
7. DISCONNECT UPPER SUSPENSION ARM
(a) R e m o v e t h e b o l t a n d n u t a n d d i s c onnect the upper
suspension arm from the member.
(b) Hang up the upper suspension arm using wire, etc.
8. REMOVE SHOCK ABSORBER
(a) Remove the bolt and nut and disconnect the shock absorber from the lower suspension arm.
±
SUSPENSION AND AXLE FRONT SUSPENSIONSA±29
WhereEverybodyKnowsYourName

(b) Remove 3 nuts and shock absorber from the body.
FRONT SHOCK ABSORBER
DISASSEMBLY
SA0RP±04
1. REMOVE SUSPENSION SUPPORT AND COIL SPRING
(a) Using SST, compress the coil spring.SST 09727±30020
NOTICE: Do not use an impact wrench.
It will damage the SST.
(b) Remove the suspension support center nut.
(c) Remove the suspension support, coil spring and spring bumper.
2. REMOVE INSULATOR FROM SUSPENSION SUPPORT
SA±30
±
SUSPENSION AND AXLE FRONT SUSPENSION
WhereEverybodyKnowsYourName

FRONT SHOCK ABSORBER
INSPECTION
SA0RQ±03
INSPECT SHOCK ABSORBER
Compress and extend the shock absorber rod and check that
there is no abnormal resistance or unusual operation
sounds.
If there is any abnormality, replace the shock absorber with
a new one.
NOTICE: When discarding the shock absorber, use the
following procedure.
FRONT SHOCK ABSORBER DISPOSAL
SA0RR±03
1. FULLY EXTEND SHOCK ABSORBER ROD
2. DRILL HOLE TO REMOVE GAS FROM CYLINDERUsing a drill, make a hole in the cylinder, as shown to remove
the gas inside.
CAUTION: The gas coming out is harmless, but be care-
ful of chips which may fly up when drilling.
FRONT SHOCK ABSORBER ASSEMBLY
SA0RS±05
1. INSTALL INSULATOR TO SUSPENSION SUPPORT HINT: Match the bolt of the suspension support with the cut±
out part of the insulator.
2. INSTALL SPRING BUMPER TO SHOCK ABSORBER
3. INSTALL COIL SPRING TO SHOCK ABSORBER
(a) Using SST, compress the coil spring. SST 09727±30020
NOTICE: Do not use an impact wrench.
It will damage the SST.
±
SUSPENSION AND AXLE FRONT SUSPENSIONSA±31
WhereEverybodyKnowsYourName

(b) Install the coil spring to the shock absorber.HINT: Fit the lower end of the coil spring into the gap of the
spring seat of the shock absorber.
4. INSTALL SUSPENSION SUPPORT
(a) Install the suspension support to the rod.
(b) Temporarily tighten a new nut.
(c) Turn the suspension support so that one of the bolts on the suspension support faces the same direction, as shown in
the illustration.
HINT: Align the bolt so that a line drawn between the rod and
the bolt would be 90 5 to the direction of the lower bushing.
5. REMOVE SST HINT: After removing the SST, again check the direction of
the suspension support.
FRONT SHOCK ABSORBER
INSTALLATION
SA063±05
1. INSTALL SHOCK ABSORBER TO BODY
(a) Install the shock absorber with coil spring to the body with the
3 nuts.
Torque: 35 N Vm (360 kgf Vcm, 26 ft Vlbf)
(b) Torque the temporarily tightened nut in the middle of the
suspension support.
Torque: 29 N Vm (300 kgf Vcm, 22 ft Vlbf)
(c) Install the plug to the suspension support.
SA±32
±
SUSPENSION AND AXLE FRONT SUSPENSION
WhereEverybodyKnowsYourName

2. CONNECT SHOCK ABSORBER TO LOWERSUSPENSION ARM
(a) Connect the shock absorber to lower suspension arm.
(b) Install the bolt from the rear vehicle and temporarily tighten the nut.
3. TEMPORARILY CONNECT UPPER SUSPENSION ARM TO MEMBER
(a) C onnect the upper suspension arm to the suspension
member.
(b) Install the bolt from the front vehicle and temporarily tighten the bolt and nut.
4. CONNECT ABS SPEED SENSOR AND WIRE HARNESS
(a) Clamp the wire harness to the upper suspension arm and body with the 3 bolts.
(b) Connect the speed sensor to the steering knuckle with the bolt.
Torque: 7.8 N Vm (80 kgf Vcm, 69 in. Vlbf)
5. LH side only:
CONNECT WASHER TANK
(a) Install and tighten the bolt.
±
SUSPENSION AND AXLE FRONT SUSPENSIONSA±33
WhereEverybodyKnowsYourName

(b) Install and tighten the bolt.
6. INSTALL FRONT FENDER SPLASH SHIELD
7. INSTALL DISC BRAKE CALIPERInstall the brake caliper to the steering knuckle with the 2
bolts.
Torque: 118 N Vm (1,200 kgf Vcm, 87 ft Vlbf)
8. STABILIZE SUSPENSION
(a) Install the front wheel and lower vehicle.
Torque: 103 N Vm (1,050 kgf Vcm, 76 ft Vlbf)
(b) Bounce the vehicle up and down several times to stabilize the
suspension.
(c) Jack up vehicle and remove the front wheel.
9. TIGHTEN BOLT AND NUT ON LOWER SIDE OF SHOCK ABSORBER
(a) Support the lower arm with a jack.
(b) Tighten the nut to the specified torque.
Torque: 143 N Vm (1,460 kgf Vcm, 106 ft Vlbf)
10. TIGHTEN BOLT AND NUT OF UPPER SUSPENSION ARM
Tighten the bolt and nut to the specified torque.
Torque: 164 N Vm (1,670 kgf Vcm, 121 ft Vlbf)
11. INSTALL FRONT WHEEL AND LOWER VEHICLE
Torque: 103 N Vm (1,050 kgf Vcm, 76 ft Vlbf)
12. CHECK FRONT WHEEL ALIGNMENT
(See page SA±5)
SA±34
±
SUSPENSION AND AXLE FRONT SUSPENSION
WhereEverybodyKnowsYourName