ignition LEXUS SC300 1991 Service Repair Manual

172
REMOTE CONTROL MIRROR (w/ DRIVING POSITION MEMORY)
CURRENT IS ALWAYS APPLIED TO TERMINAL +B OF REMOTE CONTROL MIRROR ECU THROUGH THE ECU±B FUSE.
WHEN THE IGNITION SW IS TURNED TO ON OR ACC POSITION, THE CURRENT FLOWS TO TERMINAL ACC OF THE REMOTE
CONTROL MIRROR ECU THROUGH THE RADIO NO. 2 FUSE.
REMOTE CONTROL MIRROR OPERATION
WHEN THE IGNITION SW IS TURNED TO ON OR ACC POSITION, THE REMOTE CONTROL MIRROR ECU OPERATES. WHEN THE
SELECT SW OF THE REMOTE CONTROL MIRROR SW IS MOVED TO THE LH POSITION AND THE OPERATION SW IS MOVED TO
ªLEFTº SIDE, A SIGNAL IS INPUT FROM TERMINAL SWO2 OF REMOTE CONTROL MIRROR ECU TO TERMINAL 2 OF REMOTE
CONTROL MIRROR SW " TERMINAL 12 "TERMINAL SWI2 OF ECU.
AS A RESULT, THE CURRENT TO TERMINAL +B OF ECU FLOWS FROM TERMINAL MHL OF ECU "TERMINAL 1 OF REMOTE
CONTROL MIRROR LH " MOTOR " TERMINAL 2 "TERMINAL M+L OF ECU "TERMINAL GND "GROUND , ROTATING THE MOTOR
TO ADJUST THE ANGLE OF THE LEFT SIDE OF THE OUTER MIRROR (DRIVER'S).
TO CHANGE THE ANGLE OF THE RIGHT SIDE OF THE MIRROR, THE OPERATION SW OF THE REMOTE CONTROL MIRROR SW IS
MOVED TO THE ªRIGHTº SIDE.
THEN, A SIGNAL IS INPUT FROM TERMINAL SWO2 OF REMOTE CONTROL MIRROR ECU " TERMINAL 2 OF REMOTE CONTROL
MIRROR SW " TERMINAL 8 "TERMINAL SWI1 OF ECU. AS A RESULT, THE CURRENT TO TERMINAL +B OF REMOTE CONTROL
MIRROR ECU FLOWS FROM TERMINAL M+L OF ECU " TERMINAL 2 OF REMOTE CONTROL MIRROR " MOTOR " TERMINAL 1 "
TERMINAL MHL OF ECU " TERMINAL GND " GROUND, CAUSING THE ANGLE OF THE OUTER MIRROR (DRIVER'S) TO CHANGE ON
THE RIGHT SIDE.
THE MOVEMENT TO OTHER POSITIONS OCCURS SIMILARLY, SO ONLY THE CURRENT FLOW TO EACH MOTOR IS SHOWN:
SELECT SW RH POSITION, OPERATION SW LEFT POSITION
TERMINAL +B OF REMOTE CONTROL MIRROR ECU "TERMINAL MHR "TERMINAL 1 OF REMOTE CONTROL MIRROR " MOTOR "
TERMINAL 2 "TERMINAL M+R OF ECU "TERMINAL GND "GROUND .
SELECT SW RH POSITION, OPERATION SW RIGHT POSITION
TERMINAL +B OF REMOTE CONTROL MIRROR ECU "TERMINAL M+R "TERMINAL 2 OF REMOTE CONTROL MIRROR " MOTOR "
TERMINAL 1 "TERMINAL MHR OF ECU " TERMINAL GND "GROUND .
SELECT SW LH POSITION, OPERATION SW UP POSITION
TERMINAL +B OF REMOTE CONTROL MIRROR ECU " TERMINAL MVL " TERMINAL 3 OF REMOTE CONTROL MIRROR " MOTOR "
TERMINAL 2 "TERMINAL M+L OF ECU "TERMINAL GND "GROUND .
SELECT SW LH POSITION, OPERATION SW DOWN POSITION
TERMINAL +B OF REMOTE CONTROL MIRROR ECU "TERMINAL M+L "TERMINAL 2 OF REMOTE CONTROL MIRROR " MOTOR "
TERMINAL 3 "TERMINAL MVL OF ECU " TERMINAL GND "GROUND .
SELECT SW RH POSITION, OPERATION SW UP POSITION
TERMINAL +B OF REMOTE CONTROL MIRROR "TERMINAL MVR "TERMINAL 3 OF REMOTE CONTROL MIRROR " MOTOR "
TERMINAL 2 "TERMINAL M+R OF ECU "TERMINAL GND "GROUND .
SELECT SW RH POSITION, OPERATION SW DOWN POSITION
TERMINAL +B OF REMOTE CONTROL MIRROR "TERMINAL M+R "TERMINAL 2 OF REMOTE CONTROL MIRROR " MOTOR "
TERMINAL 3 "TERMINAL MVR OF ECU " TERMINAL GND "GROUND .
THE NUMBER OF TURNS OF EACH MOTOR (AMOUNT OF MOVEMENT OF EACH PART OF THE MIRROR) IS DETECTED BY THE
POSITION SENSORS AND INPUT TO THE ECU, MAKING IT POSSIBLE TO PERFORM MEMORY AND RETURN FUNCTIONS FOR THE
MIRROR POSITION USING THE DRIVING POSITION MEMORY AND RETURN SWITCH.
SYSTEM OUTLINE
WhereEverybodyKnowsYourName

173
D10 DOOR LOCK MOTOR, DOOR UNLOCK DETECTION SW AND DOOR OPEN DETECTION SW LH
3±6 : CLOSED WITH FRONT DOOR LH OPEN
D12 DRIVING POSITION MEMORY AND RETURN SW
4±3 : CLOSED WITH SET SW ON
2±3 : CLOSED WITH MEMORY NO. 1 SW ON
1±3 : CLOSED WITH MEMORY NO. 2 SW ON
R18 REMOTE CONTROL MIRROR SW 2±12: CONTINUITY WITH SELECT SW AT LH POSITION AND OPERATION SW AT LEFT POSITION
2±8: CONTINUITY WITH SELECT SW AT LH POSITION AND OPERATION SW AT RIGHT POSITION
9±12: CONTINUITY WITH SELECT SW AT RH POSITION AND OPERATION SW AT LEFT POSITION
9±8: CONTINUITY WITH SELECT SW AT RH POSITION AND OPERATION SW AT RIGHT POSITION
3±12: CONTINUITY WITH SELECT SW AT LH POSITION AND OPERATION SW AT UP OPERATION
3±8: CONTINUITY WITH SELECT SW AT LH POSITION AND OPERATION SW AT DOWN POSITION
10±12: CONTINUITY WITH SELECT SW AT RH POSITION AND OPERATION SW AT UP POSITION
10±8: CONTINUITY WITH SELECT SW AT RH POSITION AND OPERATION SW AT DOWN POSITION
R 7 REMOTE CONTROL MIRROR ECU
4±GROUND : ALWAYS APPROX. 12 VOLTS
7±GROUND : APPROX. 12 VOLTS WITH IGNITION SW AT ACC OR ON POSITION
11±GROUND : ALWAYS CONTINUITY 9±GROUND : APPROX. 12 VOLTS WITH REMOTE CONTROL MIRROR LH AT UP OPERATION
8±GROUND : APPROX. 12 VOLTS WITH REMOTE CONTROL MIRROR LH AT LEFT OPERATION
13±GROUND : APPROX. 5 VOLTS
12±GROUND : ALWAYS CONTINUITY 2±GROUND : APPROX. 12 VOLTS WITH REMOTE CONTROL MIRROR RH AT UP OPERATION
1±GROUND : APPROX. 12 VOLTS WITH REMOTE CONTROL MIRROR RH AT LEFT OPERATION
: PARTS LOCATION
CODESEE PAGECODESEE PAGECODESEE PAGE
D1030R 8B29R1831
D1230R1631T1029
R 7A29R1731
: JUNCTION BLOCK AND WIRE HARNESS CONNECTOR
CODESEE PAGEJUNCTION BLOCK AND WIRE HARNESS (CONNECTOR LOCATION)
1D20FRONT DOOR LH WIRE
1H
1I20COWL WIRE
1J
: CONNECTOR JOINING WIRE HARNESS AND WIRE HARNESS
CODESEE PAGEJOINING WIRE HARNESS AND WIRE HARNESS (CONNECTOR LOCATION)
IF136FRONT DOOR LH WIRE AND COWL WIRE (LEFT KICK PANEL)IF236FRONT DOOR LH WIRE AND COWL WIRE (LEFT KICK PANEL)
IP138FRONT DOOR RH WIRE AND COWL WIRE (RIGHT KICK PANEL)IP238FRONT DOOR RH WIRE AND COWL WIRE (RIGHT KICK PANEL)
BT140FLOOR WIRE AND COWL WIRE (LEFT KICK PANEL)
BU140FLOOR WIRE AND INSTRUMENT PANEL WIRE (LEFT KICK PANEL)
Ba142FLOOR WIRE AND FRONT SEAT LH WIRE (UNDER THE FRONT LH SEAT)
: GROUND POINTS
CODESEE PAGEGROUND POINTS LOCATION
IF36LEFT KICK PANEL
IG36INSTRUMENT PANEL BRACE LH
IH36UNDER THE ASHTRAY LH
: SPLICE POINTS
CODESEE PAGEWIRE HARNESS WITH SPLICE POINTSCODESEE PAGEWIRE HARNESS WITH SPLICE POINTS
I 3I1138COWL WIRE
I 438COWL WIREB 940FLOOR MAIN WIRE
I 5B2746FRONT SEAT LH WIRE
SERVICE HINTS
WhereEverybodyKnowsYourName

176
REMOTE CONTROL MIRRORS (w/o DRIVING POSITION MEMORY)
R18 REMOTE CONTROL MIRROR SW
12±GROUND : APPROX. 12 VOLTS WITH IGNITION SW AT ACC OR ON POSITION
11±8 : CONTINUITY WITH OPERATION SW AT LEFT OR UP POSITION
3±11 : CONTINUITY WITH OPERATION SW AT RIGHT OR DOWN POSITION
8±GROUND : ALWAYS CONTINUITY
: PARTS LOCATION
CODESEE PAGECODESEE PAGECODESEE PAGE
R1631R1731R1831
: JUNCTION BLOCK AND WIRE HARNESS CONNECTOR
CODESEE PAGEJUNCTION BLOCK AND WIRE HARNESS (CONNECTOR LOCATION)
1D20FRONT DOOR LH WIRE
1J20COWL WIRE
: CONNECTOR JOINING WIRE HARNESS AND WIRE HARNESS
CODESEE PAGEJOINING WIRE HARNESS AND WIRE HARNESS (CONNECTOR LOCATION)
IF238FRONT DOOR LH WIRE AND COWL WIRE (LEFT KICK PANEL)
IP138FRONT DOOR RH WIRE AND COWL WIRE (RIGHT KICK PANEL)
: GROUND POINTS
CODESEE PAGEGROUND POINTS LOCATION
IF36LEFT KICK PANEL
: SPLICE POINTS
CODESEE PAGEWIRE HARNESS WITH SPLICE POINTSCODESEE PAGEWIRE HARNESS WITH SPLICE POINTS
B 3240FRONT DOOR LH WIRE
21
3 X2 3 XX
X X 8 9 10 11 12
R16, R17 R18
SERVICE HINTS
WhereEverybodyKnowsYourName

213
R 4(A) RADIO AND PLAYER
(A) 3±GROUND : APPROX. 12 VOLTS WITH IGNITION SW AT ACC OR ON POSITION
(A) 4±GROUND : ALWAYS APPROX. 12 VOLTS
S14(B) STEREO POWER AMPLIFIER
(B) 7±GROUND : ALWAYS CONTINUITY
: PARTS LOCATION
CODESEE PAGECODESEE PAGECODESEE PAGE
A1528L 630S14B31
A3230R 2B29S22A29
C 9D28R 3C29S23B29
C20A30R 4A29T16A31
C21B30R1231T17B31
F1130R1331W 931
F1230S13A31W1031
: RELAY BLOCKS
CODESEE PAGERELAY BLOCKS (RELAY BLOCK LOCATION)
219ENGINE COMPARTMENT LEFT
: JUNCTION BLOCK AND WIRE HARNESS CONNECTOR
CODESEE PAGEJUNCTION BLOCK AND WIRE HARNESS (CONNECTOR LOCATION)
1C20INSTRUMENT PANEL WIRE
1E20FLOOR WIRE
: CONNECTOR JOINING WIRE HARNESS AND WIRE HARNESS
CODESEE PAGEJOINING WIRE HARNESS AND WIRE HARNESS (CONNECTOR LOCATION)
IF136FRONT DOOR LH WIRE AND COWL WIRE (LEFT KICK PANEL)
IF236FRONT DOOR LH WIRE AND COWL WIRE (LEFT KICK PANEL)
IG236INSTRUMENT PANEL WIRE AND COWL WIRE (R/B NO. 5)
IP138FRONT DOOR RH WIRE AND COWL WIRE (RIGHT KICK PANEL)
IQ138INSTRUMENT PANEL WIRE AND CONSOLE BOX WIRE (UNDER THE INSTRUMENT PANEL CENTER)IQ238INSTRUMENT PANEL WIRE AND CONSOLE BOX WIRE (UNDER THE INSTRUMENT PANEL CENTER)
BT140FLOOR WIRE AND COWL WIRE (LEFT KICK PANEL)
BV1
BV240FLOOR NO. 3 WIRE AND CONSOLE BOX WIRE (UNDER THE INSTRUMENT PANEL CENTER)
BV3
40FLOOR NO. 3 WIRE AND CONSOLE BOX WIRE (UNDER THE INSTRUMENT PANEL CENTER)
Bc140FLOOR NO 3 WIRE AND FLOOR WIRE (UNDER THE LEFT SIDE OF REAR SEAT CUSHION)Bc240FLOOR NO. 3 WIRE AND FLOOR WIRE (UNDER THE LEFT SIDE OF REAR SEAT CUSHION)
: GROUND POINTS
CODESEE PAGEGROUND POINTS LOCATION
II36UNDER THE ASHTRAY RH
BM40BACK PANEL CENTER
: SPLICE POINTS
CODESEE PAGEWIRE HARNESS WITH SPLICE POINTSCODESEE PAGEWIRE HARNESS WITH SPLICE POINTS
I3038CONSOLE BOX WIREB23
I3138CONSOLE BOX WIREB2440FLOOR NO. 3 WIRE
B16B25
40FLOOR NO. 3 WIRE
B1940FLOOR NO. 3 WIREB3540FLOOR MAIN WIRE
B22B3740FLOOR NO. 3 WIRE
SERVICE HINTS
WhereEverybodyKnowsYourName

216
RADIO AND PLAYER (w/o CD PLAYER)
R 5(A) RADIO AND PLAYER
(A) 3±GROUND : APPROX. 12 VOLTS WITH IGNITION SW AT ACC OR ON POSITION
(A) 4±GROUND : ALWAYS APPROX. 12 VOLTS
(A) 7±GROUND : ALWAYS CONTINUITY
: PARTS LOCATION
CODESEE PAGECODESEE PAGECODESEE PAGE
A1528R 3B29T16A31
A3230R 5C29T17B31
F1130R 6D29W 931
F1230R1231W1031
R 2A29R1331
: RELAY BLOCKS
CODESEE PAGERELAY BLOCKS (RELAY BLOCK LOCATION)
219ENGINE COMPARTMENT LEFT
: JUNCTION BLOCK AND WIRE HARNESS CONNECTOR
CODESEE PAGEJUNCTION BLOCK AND WIRE HARNESS (CONNECTOR LOCATION)
1C20FLOOR WIRE
1E20INSTRUMENT PANEL WIRE
: CONNECTOR JOINING WIRE HARNESS AND WIRE HARNESS
CODESEE PAGEJOINING WIRE HARNESS AND WIRE HARNESS (CONNECTOR LOCATION)
IE136ENGINE ROOM MAIN WIRE AND COWL WIRE (R/B NO. 4)
IF236FRONT DOOR LH WIRE AND COWL WIRE (LEFT KICK PANEL)
IG236INSTRUMENT PANEL WIRE AND COWL WIRE (R/B NO. 5)
IP138FRONT DOOR RH WIRE AND COWL WIRE (RIGHT KICK PANEL)
IQ138INSTRUMENT PANEL WIRE AND CONSOLE BOX WIRE (UNDER THE INSTRUMENT PANEL CENTER)IQ238INSTRUMENT PANEL WIRE AND CONSOLE BOX WIRE (UNDER THE INSTRUMENT PANEL CENTER)
BT140FLOOR WIRE AND COWL WIRE (LEFT KICK PANEL)
BU140INSTRUMENT PANEL WIRE AND FLOOR WIRE (LEFT KICK PANEL)
BV140FLOOR NO 3 WIRE AND CONSOLE BOX WIRE (UNDER THE INSTRUMENT PANEL CENTER)BV240FLOOR NO. 3 WIRE AND CONSOLE BOX WIRE (UNDER THE INSTRUMENT PANEL CENTER)
Bc140FLOOR NO 3 WIRE AND FLOOR WIRE (UNDER THE LEFT SIDE OF REAR SEAT CUSHION)Bc240FLOOR NO. 3 WIRE AND FLOOR WIRE (UNDER THE LEFT SIDE OF REAR SEAT CUSHION)
: GROUND POINTS
CODESEE PAGEGROUND POINTS LOCATION
II36UNDER THE ASHTRAY RH
BM40BACK PANEL CENTER
: SPLICE POINTS
CODESEE PAGEWIRE HARNESS WITH SPLICE POINTSCODESEE PAGEWIRE HARNESS WITH SPLICE POINTS
I3138CONSOLE BOX WIREB1940FLOOR NO. 3 WIRE
B1640FLOOR NO. 3 WIRE
SERVICE HINTS
WhereEverybodyKnowsYourName

7XXX XX X
10 12 12
87 BA
N2
C22
A1 3
A12
A(
W/ MEMORY )
R16, R17
54B
R16, R17 (
W/O MEMORY ) 1
R
14 ,
R15
AB
193
DEFOGGER RELAY
2±4 : CLOSED WITH IGNITION SW AT ON POSITION AND DEFOGGER SW (A/C CONTROL ASSEMBLY) ON
: PARTS LOCATION
CODESEE PAGECODESEE PAGECODESEE PAGE
A12B28R14A31R17A31
A13A28R15B31R17B31
C2230R16A31
N 227R16B31
: RELAY BLOCKS
CODESEE PAGERELAY BLOCKS (RELAY BLOCK LOCATION)
219ENGINE COMPARTMENT LEFT
: JUNCTION BLOCK AND WIRE HARNESS CONNECTOR
CODESEE PAGEJUNCTION BLOCK AND WIRE HARNESS (CONNECTOR LOCATION)
1A20ENGINE ROOM MAIN WIRE1B20ENGINE ROOM MAIN WIRE
1C20FLOOR WIRE
1D20FRONT DOOR LH WIRE
1E20INSTRUMENT PANEL WIRE
1H20COWL WIRE1J20COWL WIRE
3A22INSTRUMENT PANEL WIRE3G22INSTRUMENT PANEL WIRE
: CONNECTOR JOINING WIRE HARNESS AND WIRE HARNESS
CODESEE PAGEJOINING WIRE HARNESS AND WIRE HARNESS (CONNECTOR LOCATION)
IE136ENGINE ROOM MAIN WIRE AND COWL WIRE (R/B NO. 4)
IG136INSTRUMENT PANEL WIRE AND COWL WIRE (R/B NO. 5)
IP138FRONT DOOR RH WIRE AND COWL WIRE (RIGHT KICK PANEL)
IQ138INSTRUMENT PANEL WIRE AND CONSOLE BOX WIRE (UNDER THE INSTRUMENT PANEL CENTER)
Bc240FLOOR NO. 3 WIRE AND FLOOR WIRE (UNDER THE LEFT SIDE OF REAR SEAT CUSHION)
: GROUND POINTS
CODESEE PAGEGROUND POINTS LOCATION
EB34FRONT SIDE OF LEFT FENDER
IF36LEFT KICK PANEL
IJ36RIGHT KICK PANEL
BL40UNDER THE CENTER PILLAR RH
: SPLICE POINTS
CODESEE PAGEWIRE HARNESS WITH SPLICE POINTSCODESEE PAGEWIRE HARNESS WITH SPLICE POINTS
E 934ENGINE ROOM MAIN WIRE
SERVICE HINTS
WhereEverybodyKnowsYourName

188
SHIFT LOCK
1E
21E 17 1I 10
7 8 SHIFT LOCK
CONTROL SW
SHIFT LOCK
SOLENOID
TIMER
3
2 4
5
1
P1
±P
P2
SLS±
SLS+
1 2
IF 15A
CIG
15A
ECU±IG 15A
STOP
KEY INTERLOCK
SOLENOID
[IGNITION SW] STOP LIGHT
SW
ACC IG STP
KLS+ EL±RL
G±W G
G±R
V
W±B
W±B W±B
L±R
B±R
G±W G±W W B±R
L±R
SHIFT LOCK ECU
FROM POWER SOURCE SYSTEM
(
SEE PAGE 56 )
I15 S12
S10
1H
1
3A
5
3G
6
1E
20
IG1
12
1H
13
1J
1 1E
18
V
3A
1 3H
15
W±B
WhereEverybodyKnowsYourName

189
WHEN THE IGNITION SW IS TURNED TO ACC POSITION THE CURRENT FROM THE CIG FUSE FLOWS TO TERMINAL 1 OF THE SHIFT
LOCK ECU, IN THE ON POSITION, THE CURRENT FROM THE ECU±IG FUSE FLOWS TO TERMINAL 5 OF THE ECU.
1. SHIFT LOCK MECHANISM
WITH THE IGNITION SW ON, WHEN A SIGNAL THAT THE BRAKE PEDAL IS DEPRESSED (STOP LIGHT SW ON) AND A SIGNAL THAT
THE SHIFT LEVER IS PUT IN ªPº RANGE (CONTINUITY BETWEEN P1 AND P OF THE SHIFT LOCK CONTROL SW) IS INPUT TO THE
ECU, THE ECU OPERATES AND CURRENT FLOWS FROM TERMINAL 5 OF THE ECU " TERMINAL SL+ OF THE SHIFT LOCK
SOLENOID " SOLENOID " TERMINAL SL± " TERMINAL 3 OF THE ECU " GROUND. THIS CAUSES THE SHIFT LOCK SOLENOID TO
TURN ON (PLATE STOPPER DISENGAGES) AND THE SHIFT LEVER CAN SHIFT INTO RANGE OTHER THAN THE ªPº RANGE.
2. KEY INTER LOCK MECHANISM
WITH THE IGNITION SW ON OR ACC POSITION, WHEN THE SHIFT LEVER IS PUT IN ªPº RANGE (NO CONTINUIT\
Y BETWEEN P2 AND P
OF SHIFT LOCK CONTROL SW), THE CURRENT FLOWING FROM TERMINAL 2 OF THE ECU " KEY INTER LOCK SOLENOID IS CUT
OFF. THIS CAUSES THE KEY INTER LOCK SOLENOID TO TURN OFF (LOCK LEVER DISENGAGES FROM LOCK POSITION) AND THE
IGNITION KEY CAN BE TURNED FROM ACC TO LOCK POSITION. IF THE IGNITION IS LEFT IN ACC OR ON POSITION WITH THE SHIFT
LEVER IN OTHER THAN ªPº RANGE, THAN AFTER APPROX. ONE HOUR THE ECU\
OPERATES TO RELEASE THE LOCK.
S10 SHIFT LOCK ECU
1±GROUND : APPROX. 12 VOLTS WITH IGNITION SW AT ACC OR ON POSITION
5±GROUND : APPROX. 12 VOLTS WITH IGNITION SW AT ON POSITION
3±GROUND : ALWAYS CONTINUITY
4±GROUND : APPROX. 12 VOLTS WITH BRAKE PEDAL DEPRESSED
S12 STOP LIGHT SW
2±1 : CLOSED WITH BRAKE PEDAL DEPRESSED
: PARTS LOCATION
CODESEE PAGECODESEE PAGECODESEE PAGE
I1529S1029S1229
: JUNCTION BLOCK AND WIRE HARNESS CONNECTOR
CODESEE PAGEJUNCTION BLOCK AND WIRE HARNESS (CONNECTOR LOCATION)
1E20INSTRUMENT PANEL WIRE
1H
1I20COWL WIRE
1J
20COWL WIRE
3A
3G22INSTRUMENT PANEL WIRE
3H
: CONNECTOR JOINING WIRE HARNESS AND WIRE HARNESS
CODESEE PAGEJOINING WIRE HARNESS AND WIRE HARNESS (CONNECTOR LOCATION)
IG136INSTRUMENT PANEL WIRE AND COWL WIRE (R/B NO. 5)
: GROUND POINTS
CODESEE PAGEGROUND POINTS LOCATION
IF36LEFT KICK PANEL
X 78 12345
12
I15 S 10 S 12
BLACK
SYSTEM OUTLINE
SERVICE HINTS
WhereEverybodyKnowsYourName

177
SRS AIRBAG
NOTICE: When inspecting or repairing the SRS AIRBAG, perform the operation in accord\
ance with the
following precautionary instructions and the procedure and precautions in the Repair Manual for the applicable
model year.

Malfunction symptoms of the airbag system are difficult to confirm, so the diagnostic codes become the most
important source of information when troubleshooting.
When troubleshooting the airbag system, always inspect the diagnostic codes before disconnecting the
battery.

Work must be started after 30 seconds or longer from the time the Ignition SW is set to the ªLOCKº position
and the negative (±) terminal cable is disconnected from the battery.
(The airbag system is equipped with a back±up power source so that if work is started within 30 seconds of
disconnecting the negative (±) terminal cable of the battery, the airbag may be deployed.)
When the negative (±) terminal cable is disconnected from the battery, memory of the clock and audio systems
will be cancelled. So before starting work, make a record of the contents memorized by each me\
mory system.
Then when work is finished, reset the clock and audio system as before.
When the vehicle has tilt and telescopic steering, power seat, outside r\
ear view mirror and power shoulder
belt anchorage, which are all equipped with memory function, it is not possible to make a record of the memory
contents. So when the operation is finished, it will be necessary to explain this\
fact to the customer, and
request the customer to adjust the features and reset the memory.
To avoid erasing the memory of each memory system, never use a back±up \
power supply from outside the
vehicle.

When removing the steering wheel pad or handling a new steering wheel pad, keep the pad upper surfa\
ce
facing upward. Also, lock the lock lever of the twin lock type connector\
at the rear of the pad and take care
not to damage the connector.
(Storing the pad with its metallic surface up may lead to a serious accident if \
the airbag inflates for some
reason).

Store the steering wheel pad where the ambient temperature remains below\
93 °C (200 °F), without high
humidity and away from electrical noise.

Never use airbag parts from another vehicle. When replacing airbag parts\
, replace them with new parts.

Never disassemble or repair the steering wheel pad, center airbag sensor asse\
mbly or front airbag sensors.

Before repairing the body, remove the airbag sensors if during repair shocks are likely to be app\
lied to the
sensors due to vibration of the body or direct tapping with tools or oth\
er parts.

Do not reuse a steering wheel pad or front airbag sensors.
After evaluating whether the center airbag sensor assembly is damaged or not, decide whether or not to reuse
it. (See the Repair Manual for the method for evaluating the center airbag\
sensor assembly.)

When troubleshooting the airbag system, use a high±impedance (Min. 1\
0k W/V) tester.

The vehicle wiring harness exclusively for the airbag system is distinguish\
ed by corrugated yellow tubing, as
are the connectors.

Do not measure the resistance of the airbag squib.
(It is possible this will deploy the airbag and is very dangerous.)

If the wire harness used in the airbag system is damaged, replace the wh\
ole wire harness assembly.
When the connector to the airbag front sensors can be repaired alone (when \
there is no damage to the wire
harness), use the repair wire specially designed for the purpose.
(Refer to the Repair Manual for the applicable Model year for details o\
f the replacement method.)

INFORMATION LABELS (NOTICES) are attached to the periphery of the airbag componen\
ts. Follow the
instructions on the notices.
WhereEverybodyKnowsYourName

181
THE SRS (SUPPLEMENTAL RESTRAINT SYSTEM) AIRBAG IS A DRIVER PROTECTION DEVICE WHICH HAS A SUPPLEMENTAL ROLE
TO THE SEAT BELTS.
CURRENT FLOWS CONSTANTLY TO TERMINAL 6 OF THE CENTER AIRBAG SENSOR ASSEMBLY. WHEN THE IGNITION SW IS
TURNED TO ACC OR ON, CURRENT FROM THE CIG FUSE FLOWS TO TERMINAL 14 OF THE CENTER AIRBAG SENSOR ASSEMBLY.
ONLY WHEN THE IGNITION SW IS ON DOES THE CURRENT FROM THE IGN FUSE TO TERMINAL 7 .
IF AN ACCIDENT OCCURS WHILE DRIVING, DECELERATION CAUSED BY A FRONTAL IMPACT IS DETECTED BY EACH SENSOR AND
SWITCH, AND WHEN THE FRONTAL IMPACT EXCEEDS A SET LEVEL (WHEN THE SAFING SENSOR BUILT INTO THE CENTER AIRBAG
SENSOR ASSEMBLY IS ON AND THE CENTER AIRBAG SENSOR IS ON, FRONT AIRBAG SENSORS ARE OFF), CURRENT \
FROM THE
CIG OR IGN FUSE FLOWS TO TERMINAL 11 OF THE CENTER AIRBAG SENSOR ASSEMBLY " TERMINAL 1 OF THE AIRBAG SQUIB "
SQUIB " TERMINAL 2 " TERMINAL 10 OF CENTER AIRBAG SENSOR ASSEMBLY " TERMINAL 8, TERMINAL 13 OR BODY GROUND
" GROUND.
WHEN THE SAFING SENSOR BUILT INTO THE CENTER AIRBAG SENSOR ASSEMBLY IS ON AND THE FRONT AIRBAG SENSOR LH OR
RH IS ON, CENTER AIRBAG SENSOR IS OFF AND CURRENT FROM THE CIG OR IGN FUSE FLOWS TO TERMINAL 11 OF THE CENTER
AIRBAG SENSOR ASSEMBLY " TERMINAL 1 OF THE AIRBAG SQUIB " SQUIB " TERMINAL 2 " TERMINAL 10 OF CENTER AIRBAG
SENSOR ASSEMBLY " TERMINAL 3 OR 4 " TERMINAL 1 OF FRONT AIRBAG SENSOR " TERMINAL 2 " TERMINAL 2 OR 5 OF
CENTER AIRBAG SENSOR ASSEMBLY " TERMINAL 8, TERMINAL 13 OR BODY GROUND " GROUND , WHEN THE SAFING SENSOR
BUILT INTO THE CENTER AIRBAG SENSOR ASSEMBLY IS ON, AND THE FRONT AIRBAG SENSOR LH OR RH IS ON AND CENTER
AIRBAG SENSOR IS ON ONE OF THE ABOVE±MENTIONED CIRCUITS IS ACTIVATED SO THAT CURRENT FLOWS TO THE AIRBAG
SQUIB AND CAUSES IT TO OPERATE. THE BAG STORED INSIDE THE STEERING WHEEL PAD IS INSTANTANEOUSLY EXPANDED TO
SOFTEN THE SHOCK TO THE DRIVER.
: PARTS LOCATION
CODESEE PAGECODESEE PAGECODESEE PAGE
A2928C1228T 629
C 326F 126
C1028F 226
: JUNCTION BLOCK AND WIRE HARNESS CONNECTOR
CODESEE PAGEJUNCTION BLOCK AND WIRE HARNESS (CONNECTOR LOCATION)
1E20INSTRUMENT PANEL WIRE
1G20COWL NO. 2 WIRE
1J20COWL WIRE
3A
3B
3D22INSTRUMENT PANEL WIRE
3E
3H
: CONNECTOR JOINING WIRE HARNESS AND WIRE HARNESS
CODESEE PAGEJOINING WIRE HARNESS AND WIRE HARNESS (CONNECTOR LOCATION)
IK136ENGINE WIRE AND INSTRUMENT PANEL WIRE (RIGHT KICK PANEL)
: GROUND POINTS
CODESEE PAGEGROUND POINTS LOCATION
EC34FRONT SIDE OF INTAKE MANIFOLD
ED34REAR SIDE OF CYLINDER HEAD RH
IF36LEFT KICK PANEL
: SPLICE POINTS
CODESEE PAGEWIRE HARNESS WITH SPLICE POINTSCODESEE PAGEWIRE HARNESS WITH SPLICE POINTS
E2034ENGINE WIRE
SYSTEM OUTLINE
WhereEverybodyKnowsYourName