LEXUS SC300 1999 Owners Manual

COMFORT ADJUSTMENT
163
CAUTION
Push and pull the child restraint system in different dir ections
to be sure it is secure. Follow all the installation instructions
provided by its manufacturer.

COMFORT ADJUSTMENT
1644. To remove the convertible seat, press the buckle±release
button and allow the belt to retract completely. The belt will
move freely again and be ready to work for an adult or older
child passenger.
(C) Booster seat installation
A booster seat is used in forward±facing position only.

COMFORT ADJUSTMENT
165
CAUTION

A forward±facing child restraint system should be put on
the front seat only when it is unavoidable. Always move the
seat as far back as possible, because the force of a deploying
airbag could cause death or serious injury to the child.

If you must put the convertible seat on the front seat, make
sure the seat belt hanger is secured in raised position. For
details, see page 117 in the ºSeat beltº.

COMFORT ADJUSTMENT
166
1. Sit the child on a booster seat. Run the lap and shoulder
belt through or around the booster seat and child following the
instructions provided by its manufacturer and insert the tab
into the buckle.
Make sure the shoulder belt is correctly across the child's
shoulder and that the lap belt is positioned as low as possible
on child's hips. See ºSeat beltsº on page 115 for details.

COMFORT ADJUSTMENT
167
CAUTION

Always make sure the shoulder belt is positioned across the
center of child's shoulder. The belt should be kept away
from child's neck, but not falling off child's shoulder.
Failure to do so could reduce the amount of pr otection in an
accident and cause serious injuries in a collision.

High±positioned lap belts and loose±fitting belts both could
cause serious injuries due to sliding under the lap belt
during a collision or other unintended result. Keep the lap
belt positioned as low on hip as possible.

For child's safety, do not place the shoulder belt under
child's arm.

After inserting the tab, make sure the tab and buckle are
locked and that the lap and shoulder portions of the belt are
not twisted.

Do not insert coins, clips, etc. in the buckle as this may
prevent you from properly latching the tab and buckle.

If the seat belt does not function normally, immediately
contact your Lexus dealer. Do not use the seat until the seat
belt is fixed. It cannot protect your child from injury.

COMFORT ADJUSTMENT
168
2. To remove the child restraint system, press the
buckle±release button and allow the belt to retract.DRIVING POSITION MEMORYSYSTEM
The micro computer can memorize the position of the driver's
seat, the positions of the tilt and telescopic steering, and
outside rear view mirrors. Two different driving position
profiles can be entered into the computer's memory.
This can only be done when the ignition key is in the ºONº
position, and the selector lever is in the ºPº position.
Setting a driving position

COMFORT ADJUSTMENT
169
1. Adjust the driver's seat, tilt and telescopic steering and
outside rear view mirrors to the desired position.
2. While pushing the ºSETº button, push button º1º or
º2º until the signal beeps.
The beep sound means that the positions are recorded in the
computer 's memory.
By repeating these two steps and pressing the remaining
button, the driving position for another driver can be
recorded.
To set a new memorized position, select the desired position
and perform step 2. The previous memory will be erased and
the new position will be set.
To make only slight changes to an already memorized
position, the easiest way is to first activate the memorized
position, then make the desired changes and perform step 2
above.Activating a memorized position

COMFORT ADJUSTMENT
170
When you push button º1º or º2º, the signal beeps and the
driving position automatically adjusts to the position
recorded for that button.
Conditions for memorized position activation

Ignition key ºONº
Selector lever in ºPº position
All parts of the memorized positions can be activated.
However, if the brake pedal is being depressed, the seat
position will not change.

Key not in ignition switch
Within 30 seconds of opening driver's door
The memorized position can be activated, except for the
tilt and telescopic steering. If any driving position memory switch is pushed while one of
the memorized driving position profiles is being activated,
the operation will stop.
To activate the system, push the desired button (º1º or º2º)
again.
The driving position memory control system cannot be
operated while the vehicle is moving.
If the vehicle's battery is disconnected, the computer's
memory
will be erased and the memorized positions will have
to be set again.

COMFORT ADJUSTMENT
171
CAUTION

Do not start the vehicle while the adjustments are being
made.

Take care not to select the wrong button, or the seat could
strike the rear passenger or hit your body against the
steering wheel. If this happens, you can stop the movement
by pressing another driving position memory switch, or
depressing the brake pedal.

SECTION 1 ± 7
172
INSTRUMENTS AND CONTROLS
Theft deterrent
Theft deterrent system. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
172
Theft prevention labels . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
175
THEFT DETERRENT SYSTEM
To deter theft of the vehicle, this system is designed to give
an alarm if any of the doors, trunk or hood is forcibly
unlocked or the battery terminal is disconnected and then
reconnected while the vehicle is locked.
The alarm blows the horn intermittently and flashes the
headlights, tail lights and other exterior lights.