low LEXUS SC300 1999 User Guide

KEYS AND DOORS
20In the following cases, the battery in the key may be
discharged. If this is a case, replace it using a special
screwdriver.


The remote control does not work.

The operational range of wireless remote control becomes
extremely short.

The indicator light on the key is dimmed or does not come
on.
For the replacement of the battery, see ºReplacing the
batteryº on page 25. You can also have the battery of the key
replaced by your Lexus dealer.
If you lose the wireless key, contact your Lexus dealer as soon
as possible to avoid the possibility of theft, or an accident.
You can use up to 4 wireless remote control keys for the same
vehicle. Contact your Lexus dealer for detailed information.
The wireless remote control key is an electronic
component. Observe the following instructions in order
not to cause damage to the key.

Do not leave the wireless remote control key on places
where the temperature becomes high such as on the
dashboard.

Do not disassemble it.

Avoid knocking it hard against other objects or dropping
it.

Avoid putting it in water.
Locking/Unlocking the doors
When you push the ºLOCKº button on the key briefly, all
the doors can be locked from outside the vehicle.
At this time, you can hear one beep. However, when you push
the ºLOCKº button with any door not closed securely, the
buzzer sounds for 10 seconds. To stop the buzzer, close all the
doors securely or push the ºUNLOCKº button. If the key is
in the ignition switch, locking cannot be done.
Make sure all the doors are locked when you leave the
vehicle. Push the ºLOCKº button once again. If they were
already locked, the turn signal lights will flash.
NOTICE
Do not push the ºLOCKº button any longer than 2 to 3
seconds. Pushing the button longer activates an alarm.
For details, see page 22.
When you push the ºUNLOCKº button, the driver's door
is unlocked. Pushing that button once again within 3
seconds from the first push, all other doors are also
unlocked.

KEYS AND DOORS
22
Sounding an alarm
When you push the ºLOCKº button for about 2 to 3
seconds, an alarm sounds to deter any person trying to
break into or damage your vehicle.
If you want to stop the alarm, push any button.
This function does not work when the ignition key is in the
ºONº position.
For vehicles sold in U.S.A.This device complies with Part 15 of the FCC Rules.
Operation is subject to the following two conditions:
(1) This device may not cause harmful interference,
and (2) this device must accept any interference
received, including interference that may cause
undesired operation.

KEYS AND DOORS
23
This equipment has been tested and found to comply
with the limits for a Class B digital device, pursuant
to Part 15 of the FCC Rules. These limits are
designed to provide reasonable protection against
harmful interference in a residential installation.
This equipment generates, uses and can radiate radio
frequency energy and, if not installed and used in
accordance with the instructions, may cause harmful
interference to radio communications. However,
there is no guarantee that interference will not occur
in a particular installation. If this equipment does
cause harmful interference to radio or television
reception, which can be determined by turning the
equipment off and on, the user is encouraged to try to
correct the interference by one or more of the
following measures:
± Reorient or relocate the receiving antenna.
± Increase the separation between the equipment and
receiver.
± Connect the equipment into an outlet on a circuit
different from that to which the receiver is
connected.
± Consult the dealer or an experienced radio / TV
technician for help.

KEYS AND DOORS
25
Replacing the battery
When you replace the battery, prepare a lithium battery
CR1616 and a special screwdriver.
CAUTION
Special care should be taken that small children do not
swallow the removed battery or components.
NOTICE
When replacing the battery, be careful not to lose the
components, screws and O±ring.
1. Remove the screw, and then the cover while pushing it in
the arrow direction.

SWITCHES
36
For high beam, push the lever forward. Pull it back for
low beam. For the headlight flasher, pull it further back.
A blue light in the instrument cluster indicates high beam or
headlight flasher is on.
The headlight flasher works even when the headlight switch
is off.

SWITCHES
37
For signaling turns, move the lever up or down in the
conventional manner.
The ignition key must be in the ºONº position.
The turn signal is self±cancelling after a turn, but after a lane
change, you may have to cancel it by hand. You can also
signal a lane change by moving the turn signal lever partway
and holding it there.
If the green light in the instrument cluster flashes faster than
normal, it indicates that the front or rear turn signal bulb has
burned out. If this indicator light does not come on,
the fuse
or the indicator light itself has probably failed.
FOG LIGHT SWITCH
To turn on the fog lights, turn the switch to the ºONº
position. The fog lights come on only when the headlights
are on low beam.

SWITCHES
38
WINDSHIELD WIPER ANDWASHER SWITCH
To turn the wipers on, move the lever down. To make the
washer squirt, push the button on the end of the lever.
The ignition key must be in the ºONº position.
For mist wiper operation (a single wipe), pull the lever toward
you and release it.
The interval adjuster lets you adjust the wiping time interval
between wiper sweeps if the wiper lever is in the ºINTº
position. Tw ist the lever upward to increase the time between
sweeps, and downward to decrease it.
Also, the wipers will automatically operate a couple of times
after the washer squirts even with the lever in the ºOFFº
position. The low washer fluid warning light in the instrument cluster
comes on when the fluid level in the tank becomes nearly
empty. For information on adding washer fluid, see ºAdding
washer fluidº on page 396.
In cold weather, warm the windshield with the defroster
before using the washer. This will help prevent icing, which
could block your vision.
NOTICE
Do not operate the wipers if the windshield is dry. It may
scratch the glass.

SWITCHES
41
To raise or lower the windows, use the switch on each door.
The passenger's window can also be controlled by the
switch on the driver's door.
The power windows work when the ignition key is in the
ºONº position.
Key off operation: Even if the ignition key is turned to the
ºACCº or ºLOCKº position, the window can be operated
until any of the doors is opened (or for about 60 seconds).

SWITCHES
42
Operating the driver's switch
To raise or lower the windows, pull the switch halfway up
or push it halfway down.
Automatic operation: To fully lower the window
automatically, push the switch fully down.
To stop the window partway, lightly pull the switch in the
opposite direction and then release it.

SWITCHES
43
Operating the passenger's switch
To lower the window, push the switch down. Pull it up to
raise the window. The window moves as long as the switch
is operated.
With the ºWINDOW LOCKº switch pressed in, only the
driver's window can be raised or lowered.
The indicator lights on the switch tell you which of the
switches can be operated.