VSV LEXUS SC400 1991 Service Repair Manual
[x] Cancel search | Manufacturer: LEXUS, Model Year: 1991, Model line: SC400, Model: LEXUS SC400 1991Pages: 4087, PDF Size: 75.75 MB
Page 3841 of 4087
226
AUTOMATIC AIR CONDITIONER
1. HEATER BLOWER MOTOR OPERATION
CURRENT IS APPLIED AT ALL TIMES THROUGH HEATER FUSE (60A) TO TERMINAL 5 OF HEATER RELAY. WHEN THE IGNITION SW IS
TURNED ON, CURRENT FLOWS THROUGH HEATER FUSE (10A) TO TERMINAL 1 OF HEATER RELAY " TERMINAL 3 " TERMINAL HR
OF A/C CONTROL ASSEMBLY. AT THE SAME TIME, CURRENT ALSO FLOWS FROM HEATER FUSE (10A) TO TERMINAL IG+ OF A/C
CONTROL ASSEMBLY AND TERMINAL 2 OF WATER VALVE VSV " TERMINAL 1 " TERMINAL WV OF A/C CONTROL ASSEMBLY.
* LOW SPEED OPERATION
WHEN THE BLOWER SW (A/C CONTROL ASSEMBLY) IS PUSHED TO LOW SPEED POSITION, THE CURRENT TO TERMINAL HR OF A/C
CONTROL ASSEMBLY FLOWS TO TERMINAL E OF A/C CONTROL ASSEMBLY " GROUND AND TURNS THE HEATER RELAY. AS A
RESULT, THE CURRENT TO TERMINAL 5 OF HEATER RELAY FLOWS TO TERMINAL 4 OF RELAY " TERMINAL 2 OF BLOWER
RESISTOR " TERMINAL 1 " GROUND AND CAUSES THE BLOWER MOTOR TO ROTATE AT LOW SPEED.
* MEDIUM (M1, M2, M3) AND HIGH SPEED OPERATION
WHEN THE BLOWER SW (A/C CONTROL ASSEMBLY) IS SELECTED TO MEDIUM (M1, M2, M3) OR HIGH POSITION, THE CURRENT TO
TERMINAL HR OF A/C CONTROL ASSEMBLY FLOWS TO TERMINAL E " GROUND AND TURNS THE HEATER RELAY ON. THEN, THE
CURRENT TO TERMINAL IG+ OF A/C CONTROL ASSEMBLY FLOWS TO TERMINAL BLR " TERMINAL (B)2 OF POWER TRANSISTOR
" TERMINAL (A)1 " GROUND. AS A RESULT, THE CURRENT TO TERMINAL 5 OF HEATER RELAY FLOWS TO TERMINAL 4 "
TERMINAL 2 OF BLOWER MOTOR " TERMINAL 1 " TERMINAL (A)2 OF POWER TRANSISTOR " TERMINAL (A)1 " GROUND AND
BLOWER MOTOR IS ROTATED AT SELECTED SPEED BY THE A/C CONTROL ASSEMBLY CONTROLLING THE CURRENT FLOW FROM
TERMINAL (B)2 OF POWER TRANSISTOR TO TERMINAL (B)1.
* AUTO FUNCTION
WHEN THE AUTO SW IN HEATER CONTROL SW (A/C CONTROL ASSEMBLY) IS SELECTED, THE CURRENT FLOW IS THE SAME AS
ABOVE MENTIONS, BUT THE A/C CONTROL ASSEMBLY DECIDES THE APPROPRIATE AIR FLOW VOLUME ACCORDING TO SET
TEMPERATURE AND THE INPUT SIGNALS FROM EACH SENSOR. BY CONTROLLING THE CURRENT FLOW\
FROM TERMINAL BLR OF
THE A/C CONTROL ASSEMBLY TO TERMINAL (B)2 OF POWER TRANSISTOR " TERMINAL (A)1 " GROUND , THE A/C CONTROL
ASSEMBLY CONTROLS THE BLOWER MOTOR STEPLESSLY.
2. OPERATION OF AIR INLET CONTROL SERVO MOTOR
(SWITCHING FROM FRESH TO RECIRC)
WITH IGNITION SW TURNED ON, THE CURRENT FLOWS FROM HEATER FUSE (10A) TO TERMINAL IG+ OF A/C CONTROL ASSEMBLY
" TERMINAL MREC " TERMINAL 6 OF AIR INLET CONTROL SERVO MOTOR " TERMINAL 2 " TERMINAL MFRS OF A/C CONTROL
ASSEMBLY " TERMINAL E " GROUND , THE MOTOR ROTATES AND THE DAMPER MOVES TO THE RECIRC SIDE. WHEN THE
DAMPER OPERATES WITH THE A/C SW AT RECIRC POSITION, THE DAMPER POSITION SIGNAL IS INPUT FROM TERMINAL 5 OF THE
SERVO MOTOR TO TERMINAL TPI OF THE ECU (BUILT INTO THE A/C CONTROL ASSEMBLY). AS A RESULT, CURRENT TO THE SERVO
MOTOR CIRCUIT IS CUT OFF BY THE ECU, SO THE DAMPER STOPS AT THAT POSITION.
(SWITCHING FROM RECIRC TO FRESH)
WITH IGNITION SW TURNED ON, WHEN THE RECIRC/FRESH SW IS SWITCHED TO THE FRESH SIDE, THE CURRENT FLOWS FROM
TERMINAL IG+ OF A/C CONTROL ASSEMBLY " TERMINAL MFRS " TERMINAL 2 OF AIR INLET CONTROL SERVO MOTOR "
TERMINAL 6 " TERMINAL MREC OF A/C CONTROL ASSEMBLY " TERMINAL E " GROUND , THE MOTOR ROTATES AND THE
DAMPER STOPS AT THAT POSITION.
3. OPERATION OF AIR VENT MODE CONTROL SERVO MOTOR
WITH IGNITION SW TURNED ON, THE CURRENT FLOWS FROM HEATER FUSE (10A) TO TERMINAL IG+ OF A/C CONTROL ASSEMBLY.
(SWITCHING FROM DEF TO FACE)
THE CURRENT FLOWS FROM TERMINAL MFACE OF A/C CONTROL ASSEMBLY " TERMINAL 4 OF AIR VENT CONTROL SERVO
MOTOR " TERMINAL 5 " TERMINAL MDEF OF A/C CONTROL ASSEMBLY " TERMINAL E " GROUND . THE MOTOR ROTATES AND
THE DAMPER MOVES TO THE FACE SIDE. WHEN THE DAMPER OPERATES WITH THE A/C SW AT FACE POSITION, THE DAMPER
POSITION SIGNAL IS INPUT FROM TERMINAL 1 OF THE SERVO MOTOR TO THE TERMINAL TPM OF THE ECU (BUILT INTO THE A/C
CONTROL ASSEMBLY). AS A RESULT, CURRENT TO THE SERVO MOTOR CIRCUIT IS CUT OFF BY THE ECU, SO THE DAMPER STOPS
AT THAT POSITION.
(SWITCHING FROM FACE TO DEF)
THE CURRENT FLOWS FROM TERMINAL DEF OF A/C CONTROL ASSEMBLY " TERMINAL 5 OF AIR VENT CONTROL SERVO MOTOR
" TERMINAL 4 " TERMINAL MFACE OF A/C CONTROL ASSEMBLY " TERMINAL E " GROUND , THE MOTOR ROTATES AND THE
DAMPER STOPS AT THAT POSITION.
SYSTEM OUTLINE
WhereEverybodyKnowsYourName
Page 3844 of 4087
229
FRESH RECIRC
21
II1
7IE1 13
IQ1
13
IR2
5IR1 2IR11IG1 16 IR1 3 I27
B±Y
R±Y L±RL±Y
L±W
Y
B±R R±L
R±L
BR
B±YG±RLG
GR BR
R± Y
B±Y
R±Y
R±Y
GR
A
8A 7A9B 2A4C6A 3C 5C4A 10 B 23 B11
GR
R±Y
G
G±R B±Y
R±G
L±R L±Y
L±W
Y
B± R
VSV
(
FOR WATER VALVE )
AIR INLET CONTROL
SERVO MOTOR A33
V4
62 5 3 1
BR±W
A1 2 , A 1 3 ,A1 4
A/C CONTROL ASSEMBLY CABM
BLR LV HR A/C IN MGC IG+ WV MREC MFRS RDFGR TPI ST
LG
G±R
BR±W
2 1
NOISE FILTER
( FOR A/C SYSTEM )
N4
R±G R±L
IQ 1
16 IR1 6 Y±G
BR
Y± GBR BR
WhereEverybodyKnowsYourName
Page 3869 of 4087
27
Position of Parts in Engine Compartment
I 1 ISC Valve S 3Speed Sensor No. 1
I 2 Igniter S 4 Speed Sensor No. 2 (for ECT)
I 4 Ignition Coil S 6 Starter
I 6 Injector No. 1 S 7 Starter
I 7 Injector No. 2 S 8 Sub Throttle Actuator
I 8 Injector No. 3 S 9 Sub Throttle Position Sensor
I 9 Injector No. 4
I 10 Injector No. 5 T 1 Theft Deterrent Horn
I 11 Injector No. 6 T 2 Throttle Position Sensor T 3 Traction Brake Actuator
K 1 Knock Sensor No. 1 (on Front Side) T 4 Traction Brake Actuator
K 2 Knock Sensor No. 2 (on Rear Side) T 5 Traction pump and Motor
N 1 Neutral Start SW, Back±Up Light SW and A/T Indicator SW V 1 VSV (for EGR) (Exc. USA Spec) (for A/T) V 2 VSV (for EVAP)
N 2 Noise Filter (for Defogger System) V 4 VSV (for Water Valve)
N 3 Noise Filter (for Ignition System) V 7 VSV (for Intake Control Valve)
O 2 Oil Pressure SW W 1 Washer Level SW
O 3 Oxygen Sensor Main No. 1 (on Front Side) W 2 Washer Motor
O 4 Oxygen Sensor Main No. 2 (on Rear Side) W 3 Water Temp. Sender W 5 Wiper Motor
P 1 PPS Solenoid
P 20 Power Steering Pressure SW
WhereEverybodyKnowsYourName
Page 3902 of 4087
![LEXUS SC400 1991 Service Repair Manual
67
2. CONTROL SYSTEM
*EFI (ELECTRONIC FUEL INJECTION) SYSTEM
THE EFI SYSTEM MONITORS THE ENGINE CONDITION THROUGH THE SIGNALS INPUT FROM EACH SENSOR (IN\
PUT SIGNALS
FROM (1) TO (13) ETC.) TO THE ECU](/img/36/57051/w960_57051-3901.png "LEXUS SC400 1991 Service Repair Manual
67
2. CONTROL SYSTEM
*EFI (ELECTRONIC FUEL INJECTION) SYSTEM
THE EFI SYSTEM MONITORS THE ENGINE CONDITION THROUGH THE SIGNALS INPUT FROM EACH SENSOR (IN\
PUT SIGNALS
FROM (1) TO (13) ETC.) TO THE ECU")
67
2. CONTROL SYSTEM
*EFI (ELECTRONIC FUEL INJECTION) SYSTEM
THE EFI SYSTEM MONITORS THE ENGINE CONDITION THROUGH THE SIGNALS INPUT FROM EACH SENSOR (IN\
PUT SIGNALS
FROM (1) TO (13) ETC.) TO THE ECU. THE BEST FUEL INJECTION TIMING IS DECIDED BASED ON THIS DATA AND THE PROGRAM
MEMORIZED BY THE ECU, AND THE CONTROL SIGNAL IS OUTPUT TO TERMINALS #10, #20, #30, #40, #50 AND #60 OF THE ECU TO
OPERATE THE INJECTOR. (INJECT THE FUEL). THE EFI SYSTEM PRODUCES CONTROL OF FUEL INJECTION OPERATION BY THE
ECU IN RESPONSE TO THE DRIVING CONDITIONS.
* ESA (ELECTRONIC SPARK ADVANCE) SYSTEM
THE ESA SYSTEM MONITORS THE ENGINE CONDITION THROUGH THE SIGNALS INPUT TO THE ECU FROM EACH SENSOR (INPUT
SIGNALS FROM (1), (2), (4) TO (13) ETC.). THE BEST IGNITION TIMING IS DECIDED ACCORDING TO THIS DATA AND THE
MEMORIZED DATA IN THE ECU AND THE CONTROL SIGNAL IS OUTPUT TO TERMINAL IGT THIS SIGNAL CONTROLS THE IGNITER
TO PROVIDE THE BEST IGNITION TIMING FOR THE DRIVING CONDITIONS.
* OXYGEN SENSOR HEATER CONTROL SYSTEM (USA SPEC.)
THE OXYGEN SENSOR HEATER CONTROL SYSTEM TURNS THE HEATER ON WHEN THE INTAKE AIR VOLUME IS LOW (TEMP. OF
EXHAUST EMISSIONS IS LOW), AND WARMS UP THE OXYGEN SENSOR TO IMPROVE DETECTION PERFORMANCE OF THE
SENSOR.
THE ECU EVALUATES THE SIGNALS FROM EACH SENSOR (INPUT SIGNALS FROM (1), (2), (4)\
, (9) TO (11) ETC.,) AND OUTPUTS
CURRENT TO TERMINAL HT TO CONTROL THE HEATER.
* ISC (IDLE SPEED CONTROL) SYSTEM
THE ISC SYSTEM (STEP MOTOR TYPE) INCREASES THE RPM AND PROVIDES IDLING STABILITY FOR FAST IDLE±UP WHEN THE
ENGINE IS COLD, AND WHEN THE IDLE SPEED HAS DROPPED DUE TO ELECTRICAL LOAD AND SO ON. THE ECU EVALUATES
THE SIGNALS FROM EACH SENSOR (INPUT SIGNALS FROM (1), (4), (5), (8)\
, (9), (11) ETC.), OUTPUTS CURRENT TO TERMINAL ISC1,
ISC2, ISC3 AND ISC4 TO CONTROL ISC VALVE.
* EGR CONTROL SYSTEM
THE EGR CONTROL SYSTEM DETECTS THE SIGNAL FROM EACH SENSOR (INPUT SIGNALS \
FROM (1), (4), (9), (10) ETC.), AND
OUTPUTS CURRENT TO TERMINAL EGR TO CONTROL THE EGR VALVE.
* FUEL PUMP CONTROL SYSTEM
THE COMPUTER OUTPUTS CURRENT TO TERMINAL FPC AND CONTROLS THE FUEL PUMP ECU AND FUEL PUMP DRIVE SPEED
IN RESPONSE TO CONDITIONS.
* ACIS (ACOUSTIC CONTROL INDUCTION SYSTEM)
ACIS INCLUDES A VALVE IN THE BULKHEAD SEPARATING THE SURGE TANK INTO TWO PARTS. THIS VALE IS OPENED AND
CLOSED IN ACCORDANCE WITH THE DRIVING CONDITIONS TO CONTROL THE INTAKE MANIFOLD LENGTH IN TWO STAGES FOR
INCREASED ENGINE OUTPUT IN ALL RANGES FROM LOW TO HIGH SPEEDS.
THE ECU JUDGES THE VEHICLE SPEED BY THE SIGNALS ((4), (5)) FROM EACH \
SENSOR AND OUTPUTS SIGNALS TO THE
TERMINAL ACIS TO CONTROL THE VSV (FOR OPENING AND CLOSING THE INTAKE CONTROL VALVE).
3. DIAGNOSIS SYSTEM
WITH THE DIAGNOSIS SYSTEM, WHEN THERE IS A MALFUNCTION IN THE ECU SIGNAL\
SYSTEM, THE MALFUNCTIONING SYSTEM IS
RECORDED IN THE MEMORY. THE MALFUNCTIONING SYSTEM CAN BE FOUND BY READING THE CODE DISPLAYED BY THE
CHECKING ENGINE WARNING LIGHT.
4. FAIL±SAFE SYSTEM
WHEN A MALFUNCTION HAS OCCURRED IN ANY SYSTEM, IF THERE IS A POSSIBILITY OF \
ENGINE TROUBLE BEING CAUSED BY
CONTINUED CONTROL BASED ON THE SIGNALS FROM THAT SYSTEM, THE FAIL±SAFE SYSTEM EITHER CONTROLS THE SYSTEM
BY USING DATA (STANDARD VALUES) RECORDED IN THE ECU MEMORY OR ELSE STOPS THE ENGINE.
NOTE: THE SPECIFICATION DESCRIPTIONS ªUSA SPEC.º AND ªEXC. USA SPEC.º USED IN THIS SECTION INDICATE THE
FOLLOWING SPECIFICATIONS.
USA SPEC. : USA (50 STATES) SPECIFICATIONS
EXC. USA SPEC. : USA (EXCEPT CALIFORNIA) AND CANADIAN SPECIFICATIONS.
WhereEverybodyKnowsYourName
Page 3906 of 4087
71
*1 :W/TRACTIONCONTROL
* 2 : W/O TRACTION CONTROL
BK
I22 B12
5
1
2
34
M
21
A
21 DI
A
22 FPC B
46
THG B
44
THW
2 1
2
1
BT1
2BT1 1
FPC DI E FP +B
B
L±Y
B±R
B±R
B±R
BR BR
G
L±Y
B±R
W±B G
B±R P
R±G P
R±G P
R±G
G
W±B
G
W±B W±B
B±RG EGR GAS TEMP. SENSOR
(
FOR CALIFORNIA )
EFI WATER TEMP. SENSOR
ENGINE ECU (
M/T )
FUEL PUMP ECU
FUEL PUMP
F15 F16 E11
,E1 2
E3
E4
A
B
IJ1
8IJ1 14
2 1
1 2 1 1H
41K 10
44
4IJ111
11 EC ED
E18 E20
I32I33
B
49
B
50 B 26 B27
B
7
B
25 B 80 B79
A
15
B
75 B 74 B 39 R±Y R±Y
B±R
BR
W±B
W±B BR
W
W
RY
B
L G
L±R
G±R
G±B
B±W B±R
B±RB±RB±R
B±R
2
( *2 )
(*2 )
(*1 )
( *1 )
VSV
(
FOR EGR )
VSV (
FOR EVAP )
VSV
( FOR INTAKE
CONTROL VALVE )
V1
V2
V3
10A
MIR
HTR
FROM POWER SOURCE SYSTEM
(
SEE PAGE 56 )
(
FOR USA SPEC. )(
FOR USA SPEC.)
(
SHIELDED )
( SHIELDED )
KNOCK SENSOR NO. 2
( ON REAR SIDE )
KNOCK SENSOR NO. 1
(
ON FRONT SIDE )
K1
K2
(SHIELDED )
2341
KNK1 KNK2 G1 G2 G± NE
G1 G2 G± NE
B
EO1 EO2
DISTRIBUTOR
D13
EGR EVAP ACIS
ELS
15A
TAIL
ENGINE AND ECT ECU (
A/T )
E9 , E10
AB 2
13
B±R
B±R
DIODE
WhereEverybodyKnowsYourName
Page 3956 of 4087
567 8
EB1
EC ED D DCCCCD
CCCC
C IJ2 IJ2
IG2
EB1
C D C DC C CCC
DDCDDDDDCCCCC
ED
1 2
1
2 23
1 23
14
4 234 51
25
1346
2
B±O
B±W B±OB±Y
B± R
B± R
W
R± LBR
B± R B±Y W
L±R
B±Y LG
GR±Y B Y B
G±W L±Y
R± G P B± R
B± R
18 19 17 16 15 46 23 44 34
31 32 34 32 35 33 33 24 2 76 1 37B
B± Y
B±R W
L±R
W± B
W± B
BR
LG±BL±WV±R
G± YB± Y
B± O P
B±W B± O
BR
W
L±R
B±R
P
B±O
BR
BR
#30 #20 #40 #50 #60 THG ACMG THW A/C
B±R
B±R
B±R
EB1
Fro m
Spe ed Sen sor
< 21±7>
P± L
Y± L
V± Y
Y± G
W± Y Y±R
L±R
Y± B
Y± G L±R
L±R
BR
BR
65 63 42 64 43 38 39 40 58 57 41 45 66 A9
AIR FLOW METER
From Trac tion ECU
< 8±8>
From I gniter
< 1±6>
7P
E2 IDL2 VTA2
IDL1
VTA1
THA
VC KS
IGT
IGF
VT 01
VT 02
NEO
TR
IGSW
NS W
SP1
M±REL
BATT
ISC3
ISC1
ISC4
ISC2
+B1
+B I1
ISC
VALVEBR
R±BBR
Y± L
L±R
R
Y
L±R
L±R
L±R
BR
L±R
BR
BR
BR
BR
BR W
G
From Magnet ic
Cl ut ch Rel ay
< 22±1>
To A/ C Amp lif ie r
< 22±7>
E3
EGR GAS TEMP. SENSOR
E2
EFI WATER TEMP. SENSOR
S9
SUB THROTTL E
POSITI ON SENSOR T2
THROTTLE
POSITI ON SENSOR
BR
Engine Control
2LEXUSSC300
(
Cont ' d )
ENGI NE AND ECT ECU, ENGI NE ECU *
1: (
w/ Trac tion Control )
(
* 1)
( * 2)
( * 1)
( * 2)
(
* 1 ) *
2:
(
w/ o Tr a ct i o n Co nt r ol )
(
* 1 ) To Trac ti on
ECU< 8±8>
R±B
R
4311 8
B±O
BR (
* 3)
(
* 3) *
3: (
US A S pe c. )
* 4:
(
Ex . USA Spe c. )
E9 , E10 DC
BR
Front side of
intake manifold Rear side of
c ylinder head RH Rear side of
c ylinder head RH
C
C
C 1 2
1
2
2
1
C
C
C
C
C
C
D
D
C
C
C
C
D
D
C
D
C
D
D
20
77
27
7
25
26
22
21
80
79
4
69
4
6
29
20
28
19
17
V7
VSV (
for Int ake
Contr ol Valve )
V2
VSV
(
for EVAP )
V1
VSV
(
for EGR )
BY1
BY1
BY1 BY1
BR
R±B
(
* 4 )
W
(
* 4 )
B±R
BR±W
(
* 3 )
R±L
(
* 3
)
3142 1256
IK2
IK2
12
22
C
C
1
O3
OXYGEN SENSOR
MAIN No. 1
(
ON Front Side )
C48 71 61 75 74
1
O4
OXYGEN SENSOR
MAIN No. 2
(
ON Rear Side )
C
D
1 2
35 47
P2 0
POWER STEERING
PRESSURE SW
IK11
IJ1
IJ1
(SHIELDED )2341 C
C
1
1 49
50
D1 3
DI ST RI B UTOR
( SHIELDED )
EC
Front side of
intake manifold
G±Y G± R
8
14
K1
No. 1(
ON Fr ont Side )
KNOCK SENSOR
K2
No. 2 (
ON Rear Side ) BR BR
BR
W
W L
B Y
R R±G
P
W± B
W± B G±W
L±Y
GR±Y LG
B±Y
G±Y
BR
BR
BR
G1 G2 G± NE
#10
TT TE2 VF2 TE1 VF1 W STP E1 E1 1 E0 2 E01 DI FPC G1 G2 G± NE KNK1 KNK2 STA ACI S
PS OX2 OX1 HT OX3 EGR EVAP 39
G± R G±B
B±W BR± W
BR± W
BR
B±R
B±R
B±R
B±R
W
BR± W
W
R±L
BR BR
BR
R±L W
LG±B BR
BR
(
SHI ELDED )
(
SHI EL DED )
(
SHI ELDED )
( SHIELDED )
O8
OXYGEN SENSOR SUB
(
for California )
BR
BR
Y B
R± L
BR
(* 4)
(
* 4)
(A/ T )
WhereEverybodyKnowsYourName
Page 3986 of 4087
567 8
22 LEXUS SC300(
Cont ' d )
12
II1
7
II1 2 IR2
5
IR2 4
IR2
IR1
IR1
IR1
IR1
IR2
IR2
IR2
IR2 1J
82
1E
22
5
1B
3A 3A
3A
3E
3H 3G 3B
3G
11
1E
IQ1
IQ1 IQ1 IQ1 IQ1 IQ1 II1
5
IR2
IR1
IR1
IR1
IN1
4
EB1
12 IR1
13
IR1
IR1 5
IQ117
IQ1 6
IQ1 21 12 31
IQ1 16
D
D
D
D
D
D
C
D D
D
E
E
D
IR1
4
D
C
C
D
D
E
IQ1
D
E C
D
C
E
E
E
D
D D D
D D
IQ1
C E
D
IR1
IR2
5IN11E
18
1J
1
EA IF
POWER
VOLUME AUTO
BCD SW
(Room Temp.
Contr ol SW )
M
EIR1
M
W
P± L
R±L
L±W
G± Y
G± R[ R±L
R± W
BR±W G±W BR
R±Y V
W±G BR
G± Y
Y
B±R R± G
B±Y
B±R Y
G±O V±R
V±W
L±W
BR±W G±W BR
R±Y V
L±Y
G± Y Y
B±R P± L
P
GR
G±R G Y±L
Y±G L±Y
LG±R
Y± R
L
W
L±B
Y± B P±B
W± B R
L±R
R± Y B
L±R L±O
B
R± Y L±R R
W± B P±B
L±B Y±L W
L
Y±G
LG±R
L±Y
Y±R Y± L BR
BR
BR
BR
BR
BR±W
BR
BR±W
BR±W BRBR±W
Y± GBRW
Y± L
P± B
W± B
R
BR±W
G±W BR
R±Y V
W±G BR
G± Y
Y
B±R P± L
P±B
P± B
BR
GR
BR
LG
R±L
R±L
B± Y B±Y
R± L B±Y
P± L
W
L±R
L±W
BR±W BR
BR±W
BR±W
GRBR
G±R
BR L±G
L±G
W±B
W±B W±B R
L±R
BR± W
BR
L±W
BR
BR± W
11
12
13
14
351 2 2
4
5
6
7
8
9
3
4
4
2
1
6
1
1
W/ V
MGCIGN
RDFGR ACC+B
E
DI N
MDEF
LP
MFACE TC
TPM
TW
TE
ST
TR
IG+
SET5
SET4
SET3
SET2
SET1
SAUTO
HR
S5
TP
SG
MC
MH
A/ CI N
LCKIN
LV
BL R
DOUT
TAM
TPI
MR EC
MF RS
4 5
23
8
17
8 7 3 2
16
15
14
13
12
4
9
18
22
20 3
2
7 11 9
10 25 5 8
8
1
2
3
3
2
1 9 9
5
18
8 6
10 6
8 10 1 9 13
5 9 6 7 1 15 10 15
1 4 3
127
11
7
Automatic Air Conditioner
3 1 6 5
13 3 3 5
5
12
6 19 IR2
10
DEF FACE
A3
A/C PRESSURE SW
V4
VSV(
for Water Valve )
A15
A/C CONTROL
SW AND
RADIO SW
To TDCL< 2 ±4 >
A1
A/C AMBIENT
TEMP. SENSOR
A3 3
AI R INLET CONTROL
SERVO MOTOR
To Engine and ECT ECU
<2±7>
From I gniter
< 1±5>
From Defogger
Relay< 15±3>
To TDCL< 2±4>
From Rheostat < 5±7> < 6±7> A28
AIR VENT MODE
CONTROL SERVO
MOTOR
W6
WATER TEMP. SENSOR
(
for A/C System )
A16
A/C EVAPORATOR
TEMP. SENSOR
A20
A/C SOLAR SENSOR
A19
A/C ROOM TEMP. SENSOR 15A
CIG
10A
DOME
A12 , A13 , A14
ECD
A/ C CONTROL ASSEMBLY
II1 II1
1
4
BR
G±Y
7
BR
RECIRC FRESH
3H
12 IK110
To Check Connec tor
< 2±3>BR BR
P±B P±B
Fr ont side
of right
fender Lef t kic k panel
1
2
R±LN4
NOI SE FILTER C
3
E
6
WhereEverybodyKnowsYourName
Page 3999 of 4087
52
POWER SOURCE (Current Flow Chart)*1: USA
*2: CANADA
T9 T19T11 T12
T10 W5
V3 V5 V6 W3 W2
188
11 2
194
204 200
162 216
V4 200
112 90 134 68 156
192
226 94
VSV (for EVAP) Tension Reducer
Solenoid LHTheft
Deterrent and
Door Lock ECU
Tilt and power
Telescopic ECU
Seat Heater SW (A/T)
Traction Cut SWTrip SW and
Theft Deterrent Indicator
Telephone Transceiver and
Speaker Relay
Tension Reducer
Solenoid RHVSV
(for EGR)(EX. California)
Washer Level SW Vanity Light LH
Vanity Light RH
Washer Motor
Water Temp Sender
Wiper MotorVSV (
for Water Valve)
VSV (
for Fuel Pressure Up)
*Page Nos. of
Related Systems
Parts
Code or
Location
CB or Fuse
50A DEFOG
30A DOOR
30A POWER
15A STOP
15A ECU±B
10A MIR±HTR
10A HEATER
20A TURN
20A WIPER
10A GAUGE
15A ECU±IG
7.5A ENGINE
7.5A IGN
15A CIG
7.5A RADIO No.2
15A TAIL
7.5A PANEL
7.5A ST
15A TEL
10A DOME
20A RADIO No.1
25A HAZ±HORN
30A EFI
7.5A ALT SENCING
15A HEAD LH*1
15A HEAD RH*1
15A HEAD LH±LWR*2
15A HEAD RH±LWR*2
15A HEAD LH±UPR
15A HEAD RH±UPR
60A HEATER
7.5A TRAC
15A SEAT±HTR
Location
216
90
216
Traction ECU
Traction ECU
W1
V1 V2
T18
T16
T15
T14
T13
T8
* These are the page numbers of the first page on which the related system\
is shown.
The part indicated is located somewhere in the system, not necessarily o\
n the page indicated here.
[LOCATION](1): J/B No. 1 (See page 20)(2): R/B No. 2 (See page 19)(3): R/B No. 4 (See page 23)
20 19
22
WhereEverybodyKnowsYourName
Page 4081 of 4087
15
ABBREVIATIONS
DISCONNECTION AND CONNECTION OF BOLT
TYPE CONNECTORS
For engine and ECT ECU in this vehicle, connectors are used
which require a bolt built into the connector to be screwed down to
securely connect the connector.
1. Disconnect the connectorAfter completely loosening the bolt, the two parts of the
connector can be separated.
NOTICE:
Do not pull the wire harness when disconnecting the
connector.
2. Connect the connector
NOTICE:
Before connecting the connector, always check that the
terminals are not bent or damaged.
(a) Match the guide section of the male connectorcorrectly with the female connector, then press them
together.
(b) Tighten the bolt. Make sure the connectors are completely connected,
by tightening the bolt until there is a clearance of less
than 1 mm (0.04 in.) between the bottom of male
connector and the end of female connector.
ABBREVIATIONS
The following abbreviations are used in this manual.
A/C = Air Conditioning O/D = Overdrive
ABS = Anti±Lock Brake System R/B = Relay Block
A/T = Automatic Transmission RH = Right±Hand
CB = Circuit Breaker SRS = Supplement Restraint System
COMB. = Combination SW = Switch
ECT = Electronic Controlled Transmission TDCL = Total Diagnostic Communication Link
ECU = Electronic Control Unit TEMP. = Temperature
EGR = Exhaust Gas Recirculation TRAC = Traction Control
FL = Fusible Link VSV = Vacuum Switching Valve
ISC = Idle Speed Control W/ = With
J/B = Junction Block W/O = Without
LH = Left-Hand
* The titles given inside the components are the names of the terminals (ter\
minal codes) and are not treatedas being abbreviations.
WhereEverybodyKnowsYourName