LEXUS SC400 1991 Service Repair Manual

Resistance of ECU Wiring Connectors
TerminalsConditionSTD voltage (V)
#10 (E10 ± 20)
#20 (E10 ± 19)
#30 (E10 ± 18)+ B (E9 ± 31)13 2 14 2#40 (E10 ± 17)±+ B1 (E9 ± 32) ±13.2 ± 14.2
#50 (E10 ± 16)
#60 (E10 ± 15)
ISC1 (E10 ± 35)
ISC2 (E10 ± 34)+ B (E9 ± 31)10 30ISC3 (E10 ± 33)±
+ B1 (E9 ± 32) ±10 ± 30
ISC4 (E10 ± 32)
ACIS (E10 39)+ B (E9 ± 31)38 5 44 5ACIS (E10 ± 39)±
+ B1 (E9 ± 32) ±38.5 ± 44.5
HT (E10 71)+ B (E9 ± 31)51 63HT (E10 ± 71)±
+ B1 (E9 ± 32) ±5.1 ± 6.3
EVAP (E10 74)+ B (E9 ± 31)30 34EVAP (E10 ± 74)±
+ B1 (E9 ± 32) ±30 ± 34
ERG (E10 75)+ B (E9 ± 31)33 39ERG (E10 ± 75)±
+ B1 (E9 ± 32) ±33 ± 39
IDL1 (E10 ± 64)E2 (E10 65)Throttle valve openInfinity
IDL2 (E10 ± 63)± E2 ± (E10 ± 65)Throttle valve fully closed2,300 or less
VTA1 (E10 ± 43)E2 (E10 65)Throttle valve open3,300 ± 10,000
VTA2 (E10 ± 42)± E2 ± (E10 ± 65)Throttle valve fully closed200 ± 800
VC (E10 ± 41)±E2 ± (E10 ± 65)±4,000 ± 9,000
THA (E10 ± 45)±E2 ± (E10 ± 65)Intake air temp. 20
°C (68 °F)2,000 ± 3,000
THW (E10 ± 44)±E2 ± (E10 ± 65)Coolant temp. 80 °C (176 °F)200 ± 400
THG (E10 ± 46)±E2 ± (E10 ± 65)EGR gas temp. 50 °C (112 °F)69,400 ± 88,500
G1 (E10 ± 26)G (E10 7)Camposition sensor 10 + 40°C (14 104°F)125 190G2 (E10 ± 25)±G (E10 ± 7)Cam position sensor ± 10 ± + 40°C (14 ± 104°F)125 ± 190
NE (E10 ± 27)±G (E10 ± 7)Cam position sensor ± 10 ± + 40 °C (14 ± 104 °F)155 ± 240
Engine & ECT ECU Terminals
FI±134EFI SYSTEM ± Electronic Control System (Engine & ECT ECU)
WhereEverybodyKnowsYourName

wDisconnect the SST from the wiring connectors.
SST 09990±01000
4. REINSTALL ENGINE & ECT ECU TO FLOOR PANEL
(a) Connect the two ECU connectors.w Match the male connector correctly with the female
connector, then press them together.
w Tighten the bolt.
Make sure the connector is completely connected, by tight-
ening the bolt until there is a clearance of less than 1 mm
(0.04 in.) between bottom of the male connector and end of
the female connector.
(b) Install the ECU with the bolt.
(c) Install the ECU protector with the two nuts.
(d) Install the floor carpet.
(e) Install the instrument panel under cover with the two clips.
5. RECONNECT CABLE TO NEGATIVE TERMINAL OF BATTERY FI±135
EFI SYSTEM
± Electronic Control System (Engine & ECT ECU)
WhereEverybodyKnowsYourName

Fuel Cut RPM
INSPECTION OF FUEL CUT RPM
1. WARM UP ENGINEAllow the engine to warm up to normal operating
temperature.
2. CONNECT TACHOMETER Connect the test probe of a tachometer to terminal IG of the
check connector.
NOTICE
w Never allow the tachometer terminal to touch ground as
it could result in damage to the igniter and/or ignition
coil.
w As some tachometers are not compatible with this
ignition system, we recommend that you confirm the
compatibility of yours before use.
3. INSPECT FUEL CUT OPERATION
(a) Increase the engine speed to at least 2,500 rpm.
(b) Check for injector operating noise.
(c) Check that when the throttle lever is released, injectoroperation noise stops momentarily and then resumes.
HINT:
w The vehicle should be stopped.
w Measure with the A/C OFF.
Fuel return rpm: 1,400 rpm
4. REMOVE TACHOMETER
FI±136
± Electronic Control System (Fuel \
Cut RPM)EFI SYSTEM
WhereEverybodyKnowsYourName

SERVICE SPECIFICATIONS
SERVICE DATA
Fuel pumpResistance0.2 ± 3.0

Cold start
injectorResistance
Fuel leakage2 ± 4

One drop or less per minute
Fuel pressure
regulatorFuel pressureat no vacuum265 ± 304 kPa
(2.7 ± 3.1 kgf/cm2, 38 ± 44 psi)
InjectorResistance
Injection volume
Difference between each cylinder
Fuel leakage13.4 ± 14.2

55 ± 70 cc (3.4 ± 4.3 cu in.) per 15 sec.
10 cc (0.6 cu in.) or less
One drop or less per minute
Air flow meterResistance (THA ± E2)at±20 °C (±4 °F)
at 0 °C (32 °F)
at 20 °C (68 °F)
at 40 °C (104 °F)
at 60 °C (140 °F)
at 80 °C (176 °F)10 ± 20 k

4 ± 7 k

2 ± 7 k

0.9 ± 1.3 k

0.4 ± 0.7 k

0.2 ± 0.4 k

Throttle bodyThrottle body fully closed angle6°
Throttle
positionClearance between
stop screw and leverBetween terminalsResistance
sensor
(main)0 mm
0.40 mm
0.65 mm0 in.
0.016 in.
0.026 in.VTA1 ± E2 IDL1 ± E2
IDL1 ± E2
VTA1 E2
0.2 ± 0.8 k

2.3 k
or less
Infinity
33 100k
Throttle valve fully opened position
±VTA1 ± E2VC ± E2
y
3.3 ± 10.0 k

4.0 ± 9.0 k

Sub±throttle
positionClearance between
stop screw and leverBetween terminalsResistance
sensor
(w/ TRAC)0 mm
0.30 mm
0.50 mm0 in.
0.012 in.
0.020 in.VTA2 ± E2 IDL2 ± E2
IDL2 ± E2
VTA2 E2
0.2 ± 0.8 k

2.3 k
or less
Infinity
33 100k
Throttle valve fully opened position
±VTA2 ± E2VC ± E2
y
3.3 ± 10.0 k

4.0 ± 9.0 k

Sub±throttle
actuator
(w/ TRAC)Resistance (ACM ± A and A, BCM ± B and B)0.5 ± 1.0

ISC valveResistance (B1 ± S1 and S3, B2 ± S2 and S4)10 ± 30

Cold start
injector time
switchResistance STA ± STJ below 15 °C (59 °F)
above 30 °C (86 °F)
STA ± Ground25 ± 45

65 ± 85
25 ± 85

VSV for fuel
pressure
controlResistance37 ± 44

FI±137 ± Service SpecificationsEFI SYSTEM
WhereEverybodyKnowsYourName

SERVICE DATA (Cont'd)
Water temp.
sensorResistanceat ±20°C (±4 °F)
at 0 °C (32 °F)
at 20 °C (68 °F)
at 40 °C (104 °F)
at 60 °C (140 °F)
at 80 °C (176 °F)10 ± 20 k

4 ± 7 k

2 ± 7 k

0.9 ± 1.3 k

0.4 ± 0.7 k

0.2 ± 0.4 k

EGR gas
temp.
sensorResistanceat 50°C (112 °F)
at 100 °C (212 °F)
at 150 °C (302 °F)69 ± 89 k

12 ± 15 k

2 ± 4 k

Main oxygen
sensorHeater coil resistance5.1 ± 6.3

Sub±oxygen
sensorHeater coil resistance5.1 ± 6.3

ECUHINT:

Perform all voltage and resistance measurements with the ECU connected.

Verify that the battery voltage in 11 V or above with the ignition switch is ON.
Voltage
TerminalsConditionSTD voltage (V)
BATT ± E1±10 ± 14
IGSW
+B ± E1
+B1
IG SW ON10 ± 14
VC ± E2±4.0 ± 6.0
IDL1E2
Throttle (or sub±throttle) valve fully closed1 or lessIDL1
IDL2 ± E2
IG SW ONThrottle (or sub±throttle) valve fully open10 ± 14
VTA1E2
Throttle (or sub±throttle) valve fully closed0.1 or lessVTA1
VTA 2 ± E2
Throttle (or sub±throttle) valve fully open3.0 ± 6.0
KS ± E1IdlingPulse generation
THA ± E2
THW±E2Idling
Intake air temp. 20
°C (68 °F)1.0 ± 3.0
THW ± E2IdlingEngine coolant temp. 80 °C (176 °F)0.1 ± 1.0
STA ± E1Cranking6.0 or more
#10
#20
E01IG SW ON10 ± 14#20
#30
#40±
E01
E02IdlingPulse generation
IGT1
IGT2
± E1IdlingPulse generation
FI±138EFI SYSTEM
± Service Specifications
WhereEverybodyKnowsYourName

SERVICE DATA (Cont'd)
ECU (cont'd)Voltage (cont'd)
TerminalsConditionSTD voltage (V)
IGF1E1
IG SW ON1.0 or lessIGF1
IGF2± E1
IdlingPulse generation
G1
G2 G1 (±)
G2 (±)
±IdlingPulse generation
NE ± NE (+)IdlingPulse generation
M±REL ± E1IG SW ON10 ± 14
FPC E1
Cracking, Sudden racing (6,000 rpm)4.2 ± 6.0
FPC ± E1
IdlingPulse generation
DI ± E1Idling7.5 or more
FPU E1
IG SW ON10 ± 14
FPU ± E1
Restarting high temp.2.0 or less
PAG ± E1IG SW ON10 ± 14
ISC1
ISC2
ISC3
ISC4 ± E1
IG SW ON10 ± 14
VF1
VF2
± E1Maintain engine speed at 2,500 rpm for 120 seconds
after warming up then return to idling.1.0 ± 4.0
OXR1
OXL1 ± E1Maintain engine speed at 2,500 rpm for 120 seconds
after warming upPulse generation
(0 ± 1.0)
HTR1
HTR2 E01IG SW ON10 ± 14HTR2
HTL1
HTL2±
E01
E02Idling2.0 or less
EGR1
EGR2
EGR3
EGR4 ± E1
IG SW ON10 ± 14
EGR ± E1Idling10 ± 14
KNK1
KNK2
± E1IdlingPulse generation
NSW E1IG SW ON
Shift position ºPº or ºNº range1.0 or less
NSW ± E1IG SW ON
Ex. shift position ºPº or ºNº range10 ± 14
FI±139EFI SYSTEM
± Service Specifications
WhereEverybodyKnowsYourName

SERVICE DATA (Cont'd)
ECU (cont'd)Voltage (cont'd)
TerminalsConditionSTD voltage (V)
SPD ± E1IG SW ONRotate driving wheel slowly.4 or more
TE1
TE2± E1IG SW ON10 ± 14
WE1
IG SW ON2.0 or less
W ± E1Idling10 ± 14
AD ± E1Idling10 ± 14
OD1 ± E1IG SW ON4.0 ± 6.0
A/C E1
A/C SW ON (at idling)2.0 or less
A/C ± E1A/C SW OFF10 ± 14
ACMG E1
A/C SW ON (at idling)2.0 or less
ACMG ± E1A/C SW OFF10 ± 14
TR ± E1IG SW ON10 ± 14
VT01E2IG SW ON
Throttle (or sub±throttle) valve fully closed1.0 or lessVT01
VT02 ± E2IG SW ONIG SW ON Throttle (or sub±throttle) valve fully open3.0 ± 5.5
NE0 ± E1IG SW ON4.0 ± 6.0
Resistance of wiring connector side
TerminalsConditionSTD voltage (

)
±
#10
#20
#30
#40 +B
+B1±13.2 ± 14.2
±
STJ +B
+B1±2 ± 4
±
ISC1
ISC2
ISC3
ISC4 +B
+B1±10 ± 30
±
FPU +B
+B1±37 ± 44
±
EGR1
EGR2
EGR3
EGR4 +B
+B1±19.9 ± 23.4
±
EGR +B
+B1±33 ± 39
FI±140EFI SYSTEM
± Service Specifications
WhereEverybodyKnowsYourName

SERVICE DATA (Cont'd)
ECU (cont'd)Resistance of wiring connector side (cont'd)
TerminalsConditionSTD voltage (
)
±
HTR1
HTR2
HTL1
HTL2 +B
+B1±5.1 ± 6.3
±
PA G +B
+B1±30 ± 34
±IDL1 +BThrottle valve fully openInfinity
±IDL1
IDL2
+B
+B1Throttle valve fully closed2,300 or less
±VTA1E2
Throttle valve fully open3,300 ± 10,000
±VTA1
VTA2E2
Throttle valve fully closed200 ± 800
VC ± E2±4,000 ± 9,000
THS ± E2Intake air temp, 20
°C (68 °F)2,000 ± 3,000
THW ± E2Coolant temp. 80 °C (176 °F)200 ± 400
THG ± E2EGR gas temp. 50 °C (112 °F)69,400 ± 88,500
G1
G2 G1 (±)
G2 (±)
±Cam position sensor ± 10 ± +40
°C (14 ± 104 °F)835 ± 1,350
NE ± NE (±)engine speed sensor ± 10 ± +40 °C (14 ± 104 °F)835 ± 1,350
Fuel cut rpmw/ Vehicle speed 0 km/h and coolant temp. 80 °C (176 °F)
Fuel cut rpm
Fuel return rpm
1,800 rpm
1,400 rpm
FI±141EFI SYSTEM ± Service Specifications
WhereEverybodyKnowsYourName

TORQUE SPECIFICATIONS
Part tightenedNVmkgf Vcmft Vlbf
Fuel line Union bolt type
Flare nut type2930022
Fuel pipe X Delivery pipe39400 29
Fuel pump bracket X Fuel tank5.455 48 in.Vlbf
Fuel pump set plate X Fuel tank3.940 35 in. Vlbf
Fuel tank X Body25250 18
Fuel sender gauge X Fuel tank2.930 26 in. Vlbf
Fuel inlet pipe X Fuel tank2.930 26 in. Vlbf
Fuel tank main tube X Fuel tank29300 22
Fuel tank return tube X Fuel tank29300 22
Fuel tank evaporation vent tube X Fuel tank29300 22
Air flow meter X Air cleaner case10100 7
Cold start injector X Air intake chamber7.880 69 in. Vlbf
Cold start injector tube X Cold start injector15150 11
Air intake chamber X Intake manifold18185 13
EGR pipe X Air intake chamber18185 13
EGR pipe X RH cylinder head18185 13
Cold start injector tube X RH Delivery pipe15150 11
Throttle body X Air intake chamber18185 13
Fuel return pipe X Fuel pressure regulator35360 26
Fuel pressure regulator X RH delivery pipe29300 22
Delivery pipe X Intake manifold18185 13
Fuel inlet hose X LH delivery pipe39400 29
for SST33340 24
ISC valve X Air intake chamber18185 13
Cold start injector time switch X Front water by±pass joint34350 25
Water temperature sensor X Front water by±pass joint20200 14
Water inlet housing X Water pump18185 13
EGR gas temperature sensor X EGR valve adaptor20200 14
EGR valve adaptor X Air intake chamber18185 13
EGR valve X EGR valve adaptor18185 13
Knock sensor X Cylinder block44450 33
Intake manifold X Cylinder head18185 13
Main oxygen sensor X Exhaust manifold44450 33
Sub±oxygen sensor X Exhaust manifold4445033
FI±142EFI SYSTEM ± Service Specifications
WhereEverybodyKnowsYourName

EFI SYSTEM
NOTE: The specification descriptions ºUSA Spec.º and
º Exc. USA Spec. º used in this section indicate the following
specifications.
USA Spec .: USA (50 States) Specifications
Exc. USA Spec .: USA (except California) and Canadian
Specifications. FI±1
EFI SYSTEM
WhereEverybodyKnowsYourName