remote control LEXUS SC400 1991 Service Owner's Manual

172
REMOTE CONTROL MIRROR (w/ DRIVING POSITION MEMORY)
CURRENT IS ALWAYS APPLIED TO TERMINAL +B OF REMOTE CONTROL MIRROR ECU THROUGH THE ECU±B FUSE.
WHEN THE IGNITION SW IS TURNED TO ON OR ACC POSITION, THE CURRENT FLOWS TO TERMINAL ACC OF THE REMOTE
CONTROL MIRROR ECU THROUGH THE RADIO NO. 2 FUSE.
REMOTE CONTROL MIRROR OPERATION
WHEN THE IGNITION SW IS TURNED TO ON OR ACC POSITION, THE REMOTE CONTROL MIRROR ECU OPERATES. WHEN THE
SELECT SW OF THE REMOTE CONTROL MIRROR SW IS MOVED TO THE LH POSITION AND THE OPERATION SW IS MOVED TO
ªLEFTº SIDE, A SIGNAL IS INPUT FROM TERMINAL SWO2 OF REMOTE CONTROL MIRROR ECU TO TERMINAL 2 OF REMOTE
CONTROL MIRROR SW " TERMINAL 12 "TERMINAL SWI2 OF ECU.
AS A RESULT, THE CURRENT TO TERMINAL +B OF ECU FLOWS FROM TERMINAL MHL OF ECU "TERMINAL 1 OF REMOTE
CONTROL MIRROR LH " MOTOR " TERMINAL 2 "TERMINAL M+L OF ECU "TERMINAL GND "GROUND , ROTATING THE MOTOR
TO ADJUST THE ANGLE OF THE LEFT SIDE OF THE OUTER MIRROR (DRIVER'S).
TO CHANGE THE ANGLE OF THE RIGHT SIDE OF THE MIRROR, THE OPERATION SW OF THE REMOTE CONTROL MIRROR SW IS
MOVED TO THE ªRIGHTº SIDE.
THEN, A SIGNAL IS INPUT FROM TERMINAL SWO2 OF REMOTE CONTROL MIRROR ECU " TERMINAL 2 OF REMOTE CONTROL
MIRROR SW " TERMINAL 8 "TERMINAL SWI1 OF ECU. AS A RESULT, THE CURRENT TO TERMINAL +B OF REMOTE CONTROL
MIRROR ECU FLOWS FROM TERMINAL M+L OF ECU " TERMINAL 2 OF REMOTE CONTROL MIRROR " MOTOR " TERMINAL 1 "
TERMINAL MHL OF ECU " TERMINAL GND " GROUND, CAUSING THE ANGLE OF THE OUTER MIRROR (DRIVER'S) TO CHANGE ON
THE RIGHT SIDE.
THE MOVEMENT TO OTHER POSITIONS OCCURS SIMILARLY, SO ONLY THE CURRENT FLOW TO EACH MOTOR IS SHOWN:
SELECT SW RH POSITION, OPERATION SW LEFT POSITION
TERMINAL +B OF REMOTE CONTROL MIRROR ECU "TERMINAL MHR "TERMINAL 1 OF REMOTE CONTROL MIRROR " MOTOR "
TERMINAL 2 "TERMINAL M+R OF ECU "TERMINAL GND "GROUND .
SELECT SW RH POSITION, OPERATION SW RIGHT POSITION
TERMINAL +B OF REMOTE CONTROL MIRROR ECU "TERMINAL M+R "TERMINAL 2 OF REMOTE CONTROL MIRROR " MOTOR "
TERMINAL 1 "TERMINAL MHR OF ECU " TERMINAL GND "GROUND .
SELECT SW LH POSITION, OPERATION SW UP POSITION
TERMINAL +B OF REMOTE CONTROL MIRROR ECU " TERMINAL MVL " TERMINAL 3 OF REMOTE CONTROL MIRROR " MOTOR "
TERMINAL 2 "TERMINAL M+L OF ECU "TERMINAL GND "GROUND .
SELECT SW LH POSITION, OPERATION SW DOWN POSITION
TERMINAL +B OF REMOTE CONTROL MIRROR ECU "TERMINAL M+L "TERMINAL 2 OF REMOTE CONTROL MIRROR " MOTOR "
TERMINAL 3 "TERMINAL MVL OF ECU " TERMINAL GND "GROUND .
SELECT SW RH POSITION, OPERATION SW UP POSITION
TERMINAL +B OF REMOTE CONTROL MIRROR "TERMINAL MVR "TERMINAL 3 OF REMOTE CONTROL MIRROR " MOTOR "
TERMINAL 2 "TERMINAL M+R OF ECU "TERMINAL GND "GROUND .
SELECT SW RH POSITION, OPERATION SW DOWN POSITION
TERMINAL +B OF REMOTE CONTROL MIRROR "TERMINAL M+R "TERMINAL 2 OF REMOTE CONTROL MIRROR " MOTOR "
TERMINAL 3 "TERMINAL MVR OF ECU " TERMINAL GND "GROUND .
THE NUMBER OF TURNS OF EACH MOTOR (AMOUNT OF MOVEMENT OF EACH PART OF THE MIRROR) IS DETECTED BY THE
POSITION SENSORS AND INPUT TO THE ECU, MAKING IT POSSIBLE TO PERFORM MEMORY AND RETURN FUNCTIONS FOR THE
MIRROR POSITION USING THE DRIVING POSITION MEMORY AND RETURN SWITCH.
SYSTEM OUTLINE
WhereEverybodyKnowsYourName

173
D10 DOOR LOCK MOTOR, DOOR UNLOCK DETECTION SW AND DOOR OPEN DETECTION SW LH
3±6 : CLOSED WITH FRONT DOOR LH OPEN
D12 DRIVING POSITION MEMORY AND RETURN SW
4±3 : CLOSED WITH SET SW ON
2±3 : CLOSED WITH MEMORY NO. 1 SW ON
1±3 : CLOSED WITH MEMORY NO. 2 SW ON
R18 REMOTE CONTROL MIRROR SW 2±12: CONTINUITY WITH SELECT SW AT LH POSITION AND OPERATION SW AT LEFT POSITION
2±8: CONTINUITY WITH SELECT SW AT LH POSITION AND OPERATION SW AT RIGHT POSITION
9±12: CONTINUITY WITH SELECT SW AT RH POSITION AND OPERATION SW AT LEFT POSITION
9±8: CONTINUITY WITH SELECT SW AT RH POSITION AND OPERATION SW AT RIGHT POSITION
3±12: CONTINUITY WITH SELECT SW AT LH POSITION AND OPERATION SW AT UP OPERATION
3±8: CONTINUITY WITH SELECT SW AT LH POSITION AND OPERATION SW AT DOWN POSITION
10±12: CONTINUITY WITH SELECT SW AT RH POSITION AND OPERATION SW AT UP POSITION
10±8: CONTINUITY WITH SELECT SW AT RH POSITION AND OPERATION SW AT DOWN POSITION
R 7 REMOTE CONTROL MIRROR ECU
4±GROUND : ALWAYS APPROX. 12 VOLTS
7±GROUND : APPROX. 12 VOLTS WITH IGNITION SW AT ACC OR ON POSITION
11±GROUND : ALWAYS CONTINUITY 9±GROUND : APPROX. 12 VOLTS WITH REMOTE CONTROL MIRROR LH AT UP OPERATION
8±GROUND : APPROX. 12 VOLTS WITH REMOTE CONTROL MIRROR LH AT LEFT OPERATION
13±GROUND : APPROX. 5 VOLTS
12±GROUND : ALWAYS CONTINUITY 2±GROUND : APPROX. 12 VOLTS WITH REMOTE CONTROL MIRROR RH AT UP OPERATION
1±GROUND : APPROX. 12 VOLTS WITH REMOTE CONTROL MIRROR RH AT LEFT OPERATION
: PARTS LOCATION
CODESEE PAGECODESEE PAGECODESEE PAGE
D1030R 8B29R1831
D1230R1631T1029
R 7A29R1731
: JUNCTION BLOCK AND WIRE HARNESS CONNECTOR
CODESEE PAGEJUNCTION BLOCK AND WIRE HARNESS (CONNECTOR LOCATION)
1D20FRONT DOOR LH WIRE
1H
1I20COWL WIRE
1J
: CONNECTOR JOINING WIRE HARNESS AND WIRE HARNESS
CODESEE PAGEJOINING WIRE HARNESS AND WIRE HARNESS (CONNECTOR LOCATION)
IF136FRONT DOOR LH WIRE AND COWL WIRE (LEFT KICK PANEL)IF236FRONT DOOR LH WIRE AND COWL WIRE (LEFT KICK PANEL)
IP138FRONT DOOR RH WIRE AND COWL WIRE (RIGHT KICK PANEL)IP238FRONT DOOR RH WIRE AND COWL WIRE (RIGHT KICK PANEL)
BT140FLOOR WIRE AND COWL WIRE (LEFT KICK PANEL)
BU140FLOOR WIRE AND INSTRUMENT PANEL WIRE (LEFT KICK PANEL)
Ba142FLOOR WIRE AND FRONT SEAT LH WIRE (UNDER THE FRONT LH SEAT)
: GROUND POINTS
CODESEE PAGEGROUND POINTS LOCATION
IF36LEFT KICK PANEL
IG36INSTRUMENT PANEL BRACE LH
IH36UNDER THE ASHTRAY LH
: SPLICE POINTS
CODESEE PAGEWIRE HARNESS WITH SPLICE POINTSCODESEE PAGEWIRE HARNESS WITH SPLICE POINTS
I 3I1138COWL WIRE
I 438COWL WIREB 940FLOOR MAIN WIRE
I 5B2746FRONT SEAT LH WIRE
SERVICE HINTS
WhereEverybodyKnowsYourName

174
REMOTE CONTROL MIRROR (w/ DRIVING POSITION MEMORY)
WhereEverybodyKnowsYourName

175
REMOTE CONTROL MIRRORS (w/o DRIVING POSITION MEMORY)
1D
11
MM MM
132
2
3
1
12
92 103 118
IF2
20 IF2 9
1J
1 1D
10
IP1
13 IP1 12 IP1 9 LG±R
W±B W±B
W±B
LG±R
LG±R
LG±R LG±R
LG±R
R±Y
R±Y R±Y
LG
LG±B LG±B LG LG
LG±B LG
BR±B
LG±B
BR±B BR±B
LH RH LH RH
LEFT
RIGHT
UP
DOWN
LEFT
UP
RIGHT
DOWN
SELECT SW OPERATION SW
REMOTE
CONTROL
MIRROR LH REMOTE
CONTROL
MIRROR RH
GR
7. 5A
RADIO NO. 2
REMOTE CONTROL MIRROR SW
B32
R18
R17
R16 FROM POWER SOURCE SYSTEM
(
SEE PAGE 56 )
IF2
8
IF
WhereEverybodyKnowsYourName

176
REMOTE CONTROL MIRRORS (w/o DRIVING POSITION MEMORY)
R18 REMOTE CONTROL MIRROR SW
12±GROUND : APPROX. 12 VOLTS WITH IGNITION SW AT ACC OR ON POSITION
11±8 : CONTINUITY WITH OPERATION SW AT LEFT OR UP POSITION
3±11 : CONTINUITY WITH OPERATION SW AT RIGHT OR DOWN POSITION
8±GROUND : ALWAYS CONTINUITY
: PARTS LOCATION
CODESEE PAGECODESEE PAGECODESEE PAGE
R1631R1731R1831
: JUNCTION BLOCK AND WIRE HARNESS CONNECTOR
CODESEE PAGEJUNCTION BLOCK AND WIRE HARNESS (CONNECTOR LOCATION)
1D20FRONT DOOR LH WIRE
1J20COWL WIRE
: CONNECTOR JOINING WIRE HARNESS AND WIRE HARNESS
CODESEE PAGEJOINING WIRE HARNESS AND WIRE HARNESS (CONNECTOR LOCATION)
IF238FRONT DOOR LH WIRE AND COWL WIRE (LEFT KICK PANEL)
IP138FRONT DOOR RH WIRE AND COWL WIRE (RIGHT KICK PANEL)
: GROUND POINTS
CODESEE PAGEGROUND POINTS LOCATION
IF36LEFT KICK PANEL
: SPLICE POINTS
CODESEE PAGEWIRE HARNESS WITH SPLICE POINTSCODESEE PAGEWIRE HARNESS WITH SPLICE POINTS
B 3240FRONT DOOR LH WIRE
21
3 X2 3 XX
X X 8 9 10 11 12
R16, R17 R18
SERVICE HINTS
WhereEverybodyKnowsYourName