oil LEXUS SC400 1991 Service Repair Manual

98
STOP LIGHT
1I
10
1C
21E 12
3D
13
1C
10 1H
1 3A
4
1 2
B10 B15
+
±
+
±
BM BL
B15 B14
Bd1
2 Bc1
11
Bd1
1
Bc1
7
7
84
33 4 1
11
1
2
55 1 2
W±B W±B W±B G±W
G±W
W
G±W
G±W
G±W
Y
V±G Y
Y
Y
G±W
G±W B
W±B
R±W
R±W R±W
W±B
W±B
W±B B
FROM POWER SOURCE SYSTEM
(
SEE PAGE 56 )
15A
STOP 10A
GA UGE
A
1
B
11
HOLD
CIRCUIT
W±B
STOP LIGHT
[REAR COMB. LIGHT]
LH RH
R10 R11
HIGH MOUNT STOP
LIGHT
(
W/O REAR SPOILER )
H8
HIGH MOUNT STOP
LIGHT (
W/ REAR SPOILER )
H9
LIGHT FAILURE SENSOR L3 C14 , C1 3
AB
BU1
9
V±G
STOP LIGHT
SW S12
REA R LIGHT WARNING
LIGHT [COMB. METER]
B21
W±B
W±B
WhereEverybodyKnowsYourName

11 5
CURRENT ALWAYS FLOWS TO TERMINAL (A)8 OF THE DOOR LOCK ECU THROUGH THE DOOR FUSE, AND TO TERMINAL (A)20
THROUGH THE DOME FUSE.
WHEN THE IGNITION SW IS TURNED ON, THE CURRENT FLOWING THROUGH THE ECU±IG FUSE " TERMINAL (A)2 OF THE ECU "
TERMINAL (B)8 FLOWS THROUGH THE COIL SIDE OF THE POWER MAIN RELAY TO GROUND, CAUSING THE RELAY TO OPERATE.
THE CURRENT FLOWING THROUGH THE POWER FUSE FLOWS TO THE DOOR LOCK CONTROL SW LH, CAUSING THE INDICATOR
LIGHT TO LIGHT UP.
1. MANUAL LOCK OPERATION
WHEN THE DOOR CONTROL SW OR KEY SW ARE PUSHED TO LOCK POSITION, A LOCK SIGNAL IS INPUT TO TERMINAL (A)17, (A)14
(FOR KEY SW) OF THE DOOR LOCK ECU AND CAUSES THE ECU TO FUNCTION. CURRENT FLOWS FROM TERMINAL (A)8 OF THE
ECU " TERMINAL (A)4 " TERMINAL 5 OF THE DOOR LOCK MOTORS " TERMINAL 2 " TERMINAL (A)3 OF THE ECU " TERMINAL
(A)16 " TO GROUND AND THE DOOR LOCK MOTOR CAUSES THE DOOR TO LOCK.
2. MANUAL UNLOCK OPERATION
WHEN THE DOOR LOCK CONTROL SW OR KEY ARE PUSHED TO UNLOCK POSITION, AN UNLOCK SIGNAL IS INPUT TO TERMINAL
(A)18, (A)10 (FOR KEY SW LH) OR (A)15 (FOR KEY SW RH) OF THE DOOR LOCK ECU AND CAUSES THE ECU TO FUNCTION.
CURRENT FLOWS FROM TERMINAL (A)8 OF THE ECU " TERMINAL (A)3 " TERMINAL 2 OF THE DOOR LOCK MOTORS " TERMINAL
5 " TERMINAL (A)4 OF THE ECU "TERMINAL (A)16 " TO GROUND AND THE DOOR LOCK MOTOR CAUSES THE DOOR TO
UNLOCK.
WHEN UNLOCK OPERATION OCCURS USING THE LH DOOR KEY SW, PERFORMING THE UNLOCK OPERATION ONCE UNLOCKS
ONLY THE DRIVER'S DOOR. TO UNLOCK ALL THE OTHER DOORS TOGETHER, UNLOCK OPERATION MUST BE PERFORMED AGAIN
WITHIN 3 SECONDS OF THE FIRST OPERATION.
3. IGNITION KEY REMINDER OPERATION
* OPERATION OF DOOR LOCK BUTTON (OPERATION OF DOOR LOCK MOTORS)
WHEN THE IGNITION KEY IS IN THE CYLINDER (UNLOCK WARNING SW ON) AND THE DOOR IS OPENED AND LOCKED USING
DOOR LOCK BUTTON (DOOR LOCK MOTOR), THE DOOR IS LOCKED ONCE BUT EACH DOOR IS UNLOCKED SOON BY THE
OPERATION OF THE ECU. AS A RESULT OF ECU ACTIVATION, THE CURRENT FLOWS FROM TERMINAL (A)8 OF THE ECU "
TERMINAL (A)3 " TERMINAL 2 OF THE DOOR LOCK MOTORS " TERMINAL 5 " TERMINAL (A)4 OF THE ECU " TERMINAL (A)16
" TO GROUND AND CAUSES ALL THE DOORS TO UNLOCK.
THE SAME APPLIES TO OPERATION OF THE DOOR LOCK CONTROL SW AND DOOR LOCK KEY SW.
* KEY LESS LOCK OPERATION
WHEN THE IGNITION KEY IS STILL INSERTED IN THE CYLINDER (UNLOCK WARNING SW ON), THE DOOR IS OPEN AND UNLOCK
OPERATION IS PREVENTED BY KEEPING THE DOOR LOCK BUTTON PRESSED TO THE LOCK SIDE, THE DOOR IS KEPT IN THE
LOCK CONDITION. IF THE DOOR IS THEN CLOSED, A SIGNAL IS INPUT TO THE ECU FROM THE DOOR COURTESY SW. THIS
ACTIVATES THE ECU AND EACH DOOR IS UNLOCKED.
SYSTEM OUTLINE
WhereEverybodyKnowsYourName