bulb LINCOLN BLACKWOOD 2002 Owners Manual

Brake system warning
Illuminates if the parking brake is
engaged. Also illuminates to indicate
a system check. If the brake
warning lamp does not illuminate at
these times, or illuminates after
releasing the parking brake, seek service immediately.
Anti-lock brake system (ABS)
Illuminates to ensure the circuit is
functional. If the light does not
illuminate momentarily at start up,
remains on or continues to flash, the
ABS needs to be serviced. With the
ABS light on, normal braking is still functional.
Turn signal
Illuminates when the turn signals or
the hazard lights are turned on. If
the lights stay on continuously or
flash faster, check for a burned-out
bulb.
High beams
Illuminates when the high beam
headlamps are turned on.
SecuriLockYanti-theft system
Illuminates when the anti-theft
alarm system is armed. If the light
fails to illuminate, continues to flash
or remains on, have the system
serviced.
Refer toSecuriLockypassive anti-theft systemin theControls and
featureschapter.
!
BRAKE
ABS
THEFT
Instrumentation
10

Allow the vehicle to sit for at least eight hours without starting the
engine. Then, start the engine and complete the above driving cycle. The
engine must warm up to its normal operating temperature. Once started,
do not turn off the engine until the above driving cycle is complete.
BULBS
Replacing exterior bulbs
Check the operation of the following lamps frequently:
²Headlamps
²Foglamps
²High-mount brakelamp
²Brakelamps
²Turn signals
²License plate lamp
²Tail lamps
²Back-up lamps
Do not remove lamp bulbs unless they can be replaced immediately with
new ones. If a bulb is removed for an extended period of time,
contaminants may enter the lamp housings and affect lamp performance.
Replacing headlamp bulbs
1. Make sure the headlamp control is in the OFF position.
2. Open the hood.
3. At the back of the headlamp,
remove the headlamp assembly
retainers by pushing rearward and
pulling up.
4. Pull the headlamp assembly
forward slightly to expose the
electrical connectors.
Maintenance and care
204

5. Rotate the bulb cover
counterclockwise and remove.
6. Disconnect the electrical
connector from the bulb by pulling
rearward.
7. Remove the bulb retainer ring by
turning it counterclockwise, then
slide the ring off the plastic base.
8. Without turning, carefully pull the
bulb out of the headlamp assembly.
Handle a halogen headlamp bulb carefully and keep out of
children's reach. Grasp the bulb only by its plastic base and do
not touch the glass. The oil from your hand could cause the bulb to
break the next time the headlamps are operated.
Maintenance and care
205

9. Insert the glass end of the new bulb into the headlamp assembly.
When the grooves in the plastic base are aligned, push the bulb into the
lamp assembly until the plastic base contacts the rear of the lamp
assembly.
10. To complete installation, follow the removal procedure in reverse
order.
Replacing front parking lamp/turn signal bulbs
1. Make sure the headlamp control is in the OFF position.
2. Open the hood.
3. At the back of the headlamp,
remove the headlamp assembly
retainers by pushing rearward and
pulling up.
4. Pull the headlamp assembly
forward slightly to expose the
electrical connectors.
5. Release clip and disconnect the
electrical connector from the bulb
socket.
6. Rotate the bulb socket
counterclockwise and remove.
7. Pull the bulb straight out of the
socket and push in the new bulb.
8. To complete installation of the
parking lamp/turn signal assembly,
follow the removal procedures in reverse order.
Maintenance and care
206

Replacing foglamp bulbs
The halogen bulb contains gas under pressure. The bulb may
shatter if the glass envelope is scratched or if the bulb is
dropped. Handle the bulb carefully. Grasp the bulb only by its
base. Avoid touching the glass envelope.
1. Rotate the foglamp bulb
counterclockwise and remove from
foglamp (the rear side of the
foglamp is shown).
2. Disconnect the electrical
connector from the foglamp bulb.
3. Connect the electrical connector
to the new foglamp bulb.
4. Install the foglamp bulb in
foglamp by rotating clockwise.
Replacing tail//turn/backup lamp bulbs
1. Open the tailgate dual doors to
expose the lamp assembly nut.
2. Remove the nut from the lamp
assembly.
3. Carefully pry the lamp assembly
away from the vehicle to expose the
bulb socket.
4. Rotate the bulb socket
counterclockwise and remove from
lamp assembly.
5. Pull bulb straight out of socket and push in the new bulb.
6. Install the bulb socket into the lamp assembly and rotate clockwise.
7. Carefully install the lamp assembly on the pickup box aligning the
three tabs into the slots.
8. Secure the lamp assembly on the vehicle with the nut.
Maintenance and care
207

Replacing rear cornering/backup lamp bulb
1. Reach behind the rear bumper
and remove two nuts from the lamp
assembly.
2. Carefully pull the lamp assembly
outward to expose the electrical
connector.
3. Rotate the bulb socket
counterclockwise and remove.
4. Pull the bulb straight out of the
socket and push in the new bulb.
5. To complete installation, follow the removal procedure in reverse
order.
Replacing high-mount brakelamp bulbs
1. Remove the two screws from the
high-mount brakelamp assembly.
2. Remove the bulb from the lamp
assembly by turning
counterclockwise.
3. Carefully pull the bulb straight
out of the socket and push in the
new bulb.
4. Install bulb socket in lamp
assembly by turning clockwise.
5. Install brakelamp assembly on the vehicle with two screws.
Replacing license plate lamp bulbs
For bulb replacement, see a dealer or qualified technician.
Replacing the interior bulbs
Check the operation of the following interior bulbs frequently:
²interior overhead lamp
²map lamp
For bulb replacement, see a dealer or qualified technician.
Maintenance and care
208

USING THE RIGHT BULBS
Replacement bulbs are specified in the chart below. Headlamp bulbs
must be marked with an authorized ªD.O.T.º for North America and an
ªEº for Europe to assure lamp performance, light brightness and pattern
and safe visibility. The correct bulbs will not damage the lamp assembly
or void the lamp assembly warranty and will provide quality bulb burn
time.
Function Number of bulbs Trade number
Headlamps 2 9007
Front park/turn lamps 2 3157 AK (amber)
Front sidemarker 2 194 AK (amber)
Foglamps 2 880
Dome/map lamps 2 579
Turn/tail/brake lamps 2 3157K
Rear cornering lamp 2 921
Backup lamp 2 921
License lamp 2 168
High-mount brake
lamp3 906
All replacement bulbs are clear in color except where noted.
To replace all instrument panel lights - see your dealer
Maintenance and care
209

Headlamps ...................................17
aiming ..............................210±211
autolamp system .......................18
bulb specifications ..................209
flash to pass ..............................17
high beam ...........................10, 17
replacing bulbs .......................204
turning on and off ....................17
warning chime ..........................13
Heating ........................................41
HomeLink universal
transceiver (see Garage
door opener) .........................65±68
Hood ..........................................169
I
Ignition .................................49, 222
Infant seats
(see Safety seats) .....................118
Inspection/maintenance (I/M)
testing ........................................203
Instrument panel
cleaning ...................................216
cluster ..................................8, 216
lighting up panel
and interior ...............................18
location of components ..............8
J
Jack ............................................157
positioning ...............................157
storage .....................................157
Jump-starting your vehicle ......162K
Keyless entry system
autolock .....................................85
locking and
unlocking doors ..................88±89
programming entry code .........88
Keys .................................49, 77±79
key in ignition chime ...............12
positions of the ignition ...........49
valet key ....................................49
L
Lamps
autolamp system .......................18
bulb replacement
specifications chart ................209
cargo lamps ...............................18
fog lamps ...................................17
headlamps .................................17
headlamps, flash to pass ..........17
instrument panel, dimming .....18
interior lamps .............63±64, 208
replacing bulbs .......204, 206±208
Lane change indicator
(see Turn signal) ........................49
Liftgate ........................................73
Lights, warning and indicator ......8
air bag ..........................................9
air suspension .........................133
anti-lock brakes (ABS) ....10, 129
anti-theft ...................................10
brake ..........................................10
charging system ........................11
check coolant ............................11
door ajar ....................................11
engine oil pressure ...................11
high beam .................................10
low fuel ........................................8
Index
241