keyless LINCOLN MARK VIII 1997 User Guide

127
Arming the SystemTo arm the system, do the following four steps in
sequence.
1. Remove the key from the ignition.
2. Open any door. The alarm indicator light will
start flashing to remind you to arm the system.
3. Lock the doors by using the power door lock
switch, pressing the remote entry transmitter
LOCK control or pressing the last two buttons
(7/8, 9/0) of the keyless entry keypad.
4. Close all doors. The alarm indicator light will
then remain on steadily for approximately 30
more seconds and then go out. When the light
goes out the system is armed.NOTE:Be sure to close all doors completely. If
not, the alarm indicator light will remain on.
Remember, your anti-theft system is armed only
after the alarm indicator light remains on steadily
for approximately 30 seconds after the last door is
closed, and then goes out.
You can also arm the anti-theft system with the
factory installed remote entry system or the keyless
entry system by following this sequence:
1. Remove the key from the ignition.
2. Close all of the doors.
3. Press the remote entry transmitter LOCK
control or press the last two buttons (7/8, 9/0)
of the keyless entry keypad to lock the doors.
The alarm indicator will come on for 30
seconds to show the alarm is arming and then
turn off to show that the alarm has armed.
File:05fncf8.ex
Update:Thu Jun 27 10:02:20 1996

128The anti-theft system is designed to work with the
factory installed remote entry system. It may not
work with other remote entry systems.Disarming an Untriggered Anti-Theft
SystemYou can disarm the system by:q
unlocking a front door with the key (turn the
key all the way to the end of travel or the
system will not disarm).
q
using the keyless entry unlock code.
q
using the UNLOCK button of the remote entry
transmitter.
q
turning the ignition to ON or ACC.
If you armed the system while inside your vehicle,
you can disarm it by turning the ignition to the ON
or ACC position. This allows you to open the front
door and exit without triggering the system.
Triggering the Alarm SystemThe armed system will be triggered if:q
any door is opened without disarming the
system (see previous paragraphs), or
q
the hood is opened.
Disarming a Triggered SystemThe alarm can be disarmed by:q
unlocking a front door with the key
q
using the keyless entry unlock code
q
using the UNLOCK control on the remote entry
transmitter
NOTE:The flashing lights and honking horn will
shut off automatically approximately three minutes
after the system is triggered. It will trigger again if
another intrusion occurs. However, the engine will
not be allowed to start until the system is disarmed.
File:05fncf8.ex
Update:Thu Jun 27 10:02:20 1996

305
K
Keyless entry system
locking and unlocking doors...... 119
programming entry code....... 120
Keys
key in ignition chime......... 84
positions of the ignition........ 83
removing from the ignition...... 84
stuck in lock position......... 83
L
Lamps
autolamp delay system........ 80
checking.............. 253
daytime running light system..... 78
dome lamps............. 96
flashing the lamps.......... 86
hazard flashers............ 89
headlamps............. 79
high beams............. 86
interior lamps............ 78map lamps............. 96
replacing bulbs............ 253
trailer............... 187
Lane change indicator (see Turn signal) . . 85
Lap belts............... 143
Lights, warning and indicator
airbag............... 45
anti-lock brakes (ABS)......... 11
brake................ 10
charging system........... 13
check engine............ 45
engine oil pressure.......... 11
hazard warning light......... 89
high beam............. 14
overdrive off............. 46
safety belt.............. 44
turn signal indicator......... 14
File:fnix8.ex
Update:Thu Jun 27 10:02:38 1996