wheel LINCOLN MKT 2019 Owners Manual

Non-Limousine
Note:If the third row seat is stowed in thefloor, you will need to unstow it to accessthe spare tire.
1. Park on a level surface, set the parkingbrake and activate the hazard flashers.
2. Place the transmission in park (P) andturn the engine off.
3. Block the diagonally opposite wheel.
4.Remove the carpeted floor panel locatedin the rear of the vehicle, then removethe wing nut that secures the spare tireby turning it counterclockwise.
5. Lift and remove the spare tire from thetrunk.
6. Remove the second wing nut thatsecures the jack retention bracket byturning it counterclockwise. Then removethe jack kit from the vehicle.
7.Remove the jack, L-shaped bolt, and thewrench from the felt bag. Fold down thewrench socket to use to loosen the lugnuts and to operate the jack.
8. Remove the wheel cover with the lugwrench tip and loosen each wheel lugnut one-half turn counterclockwise, butdo not remove them until the wheel israised off the ground.
9. The vehicle jacking points are shownabove, and are depicted on the warninglabel on the jack.
336
MKT (TP4) , enUSA, Edition date: 201803, Second-Printing
Wheels and TiresE142551 E211099 E145908

10. Put the jack in the jack notch next tothe tire you are changing. Turn the jackhandle clockwise until the wheel iscompletely off the ground.
11. Remove the lug nuts with the lugwrench.
12.Replace the flat tire with the spare tire,making sure the valve stem is facingoutward. Reinstall the lug nuts until thewheel is snug against the hub. Do notfully tighten the lug nuts until the wheelhas been lowered.
13. Lower the wheel by turning the jackhandle counterclockwise.
14. Remove the jack and fully tighten thelug nuts in the order shown. SeeTechnical Specifications (page 340).
15. Install the wheel cover.
Limousine
1. Park on a level surface, set the parkingbrake and activate the hazard flashers.
2. Place the transmission in park (P) andturn the engine off.
3. Block the diagonally opposite wheel.
337
MKT (TP4) , enUSA, Edition date: 201803, Second-Printing
Wheels and TiresE201156 12
3
4
5
E75442 E142551

4. Remove the wing nut that secures thespare tire by turning it counterclockwise.
5. Lift and remove the spare tire from thetrunk.
6. Remove the lug wrench (A) and jack (B)from the jack foam pockets.
7. Remove the wheel cover with the lugwrench tip and loosen each wheel lugnut one-half turn counterclockwise, butdo not remove them until the wheel israised off the ground.
8. The vehicle jacking points are shownabove, and are depicted on the warninglabel on the jack.
9.Put the jack in the jack notch next to thetire you are changing. Turn the jackhandle clockwise until the wheel iscompletely off the ground.
10. Remove the lug nuts with the lugwrench.
11.Replace the flat tire with the spare tire,making sure the valve stem is facingoutward. Reinstall the lug nuts until thewheel is snug against the hub. Do notfully tighten the lug nuts until the wheelhas been lowered.
338
MKT (TP4) , enUSA, Edition date: 201803, Second-Printing
Wheels and TiresE211467 E211468 E145908 E201156

12. Lower the wheel by turning the jackhandle counterclockwise.
13. Remove the jack and fully tighten thelug nuts in the order shown. SeeTechnical Specifications (page 340).
14. Install the wheel cover.
Stowing the flat tire
If you are stowing the flat tire, remove theL-shaped bolt from the external pocket ofthe felt bag. With the third row seat in theraised position, stand the flat tire in the rearof the vehicle with the tire’s valve stem facingthe rear of the vehicle. Fasten the flat tire tothe vehicle by inserting the L-shaped boltthrough one of the lug bolt holes in thewheel. Turn it clockwise into the threadedhole in the vehicle until the tire is secured.
If you are stowing the temporary spare tire,place the tire over the jack and secure it withthe large wing nut.
Stowing the jack
1. Fully collapse the jack, fold the lugwrench socket into the handle and placethe jack and wrench into the felt bag asshown. Place the extension bolt orL-shaped bolt into the external pocket ofthe felt bag. Position the jack as shownto make sure that the locating holes inthe jack base can be placed on thelocating tabs of the jack mountingbracket in the spare tire tub.
2.Securely close the wrench compartmentand the jack bag using the Velcro™ straps.
3. Place the jack kit on the angled bracketin the spare tire tub, using the locatingtabs to position the jack correctly.
339
MKT (TP4) , enUSA, Edition date: 201803, Second-Printing
Wheels and Tires12
3
4
5
E75442 E194296 E211100

4. Insert the straight end of the jackretention bracket through the eyelet ofthe angled bracket and swing theretention bracket over the jack. With thejack in place, place the looped end of theretention bracket over the threaded studin the trunk floor and secure it with theplastic wing nut.
TECHNICAL SPECIFICATIONS
340
MKT (TP4) , enUSA, Edition date: 201803, Second-Printing
Wheels and TiresE211101

Wheel Lug Nut Torque Specifications
WARNING: When you install a wheel, always remove any corrosion, dirt or foreign materials present on the mounting surfaces of thewheel or the surface of the wheel hub, brake drum or brake disc that contacts the wheel. Make sure to secure any fasteners that attachthe rotor to the hub so they do not interfere with the mounting surfaces of the wheel. Installing wheels without correct metal-to-metal contactat the wheel mounting surfaces can cause the wheel nuts to loosen and the wheel to come off while your vehicle is in motion, resulting inloss of vehicle control, personal injury or death.
lb.ft (Nm) *Bolt size
100 lb.ft (135 Nm)1/2 x 20
150 lb.ft (204 Nm)M14 x 1.5 (Limousine only)
*Torque specifications are for nut and bolt threads free of dirt and rust. Use only Ford recommended replacement fasteners.
Retighten the lug nuts to the specified torque within 100 miles (160 kilometers) after any wheel disturbance (such as tire rotation, changing aflat tire, wheel removal).
341
MKT (TP4) , enUSA, Edition date: 201803, Second-Printing
Wheels and Tires

Wheel pilot boreA
Inspect the wheel pilot hole and mountingsurface prior to installation. Remove anyvisible corrosion or loose particles.
342
MKT (TP4) , enUSA, Edition date: 201803, Second-Printing
Wheels and TiresE145950

CAPACITIES AND SPECIFICATIONS - 3.5L
Capacities
WARNING: The air conditioning refrigerant system contains refrigerant under high pressure. Only qualified personnel should servicethe air conditioning refrigerant system. Opening the air conditioning refrigerant system can cause personal injury.
CapacityItem
6.0 qt (5.7 L)Engine oil.
13.7 qt (13 L)Engine coolant.
Between MIN/MAX on brake fluid reservoirBrake fluid.
2.4 pt (1.15)Rear differential fluid (All Wheel Drive).
10.9 qt (10.3 L)1Automatic transmission fluid (6F50).
11.6 qt (11 L)1Automatic transmission fluid (6F55).
17.9 fl oz (0.53 L)Power Transfer Unit (PTU) fluid (All Wheel Drive).
Fill as requiredWindshield washer fluid.
18.6 gal (70.4 L)Fuel tank.
349
MKT (TP4) , enUSA, Edition date: 201803, Second-Printing
Capacities and Specifications

SpecificationName
WSS-M6C65-A2Brake fluid:Motorcraft® DOT 4 Low Viscosity (LV) High Performance Motor Vehicle Brake FluidPM-20
WSP-M2C197-ARear differential fluid (U.S.):Motorcraft® SAE 80W-90 Premium Rear Axle LubricantXY-80W90-QL
WSP-M2C197-ARear differential fluid (Canada):Motorcraft® SAE 80W-90 Premium Rear Axle LubricantCXY-80W90-1L
WSS-M2C938-AAutomatic transmission fluid (U.S.):MERCON® LVMotorcraft® MERCON® LV Automatic Transmission FluidXT-10-QLVC
WSS-M2C938-AAutomatic transmission fluid (Canada):MERCON® LVMotorcraft® MERCON® LV Automatic Transmission FluidCXT-10-LV12
WSL-M2C192-APower Transfer Unit (PTU) fluid (All Wheel Drive) (U.S.):Motorcraft® SAE 75W-140 Synthetic Rear Axle LubricantXY-75W140-QL
WSL-M2C192-APower Transfer Unit (PTU) fluid (All Wheel Drive) (Canada):Motorcraft® SAE 75W-140 Synthetic Rear Axle LubricantCXY-75W140-1L
351
MKT (TP4) , enUSA, Edition date: 201803, Second-Printing
Capacities and Specifications

CapacityItem
6.0 qt (5.7 L)Engine oil
13.2 qt (12.5 L)Engine coolant
Between MIN/MAX on brake fluid reservoirBrake fluid
2.4 pt (1.15)Rear differential fluid (All Wheel Drive)
10.9 qt (10.3 L)1Automatic transmission fluid (6F50)
11.6 qt (11 L)1Automatic transmission fluid (6F55)
17.9 fl oz (0.53 L)Power Transfer Unit (PTU) fluid (All Wheel Drive)
Fill as requiredWindshield washer fluid8.9 fl oz (265 ml)
18.6 gal (70.4 L)Fuel tank
2.31 lb (1.05 kg)A/C refrigerant
8.96 fl oz (265 ml)A/C refrigerant compressor oil
1 Approximate dry fill capacity. Actual amount may vary during fluid changes.
356
MKT (TP4) , enUSA, Edition date: 201803, Second-Printing
Capacities and Specifications